Quick start guide TL7800 DECT 6.
Quick reference guide - headset (On/off button and light) Press to make, answer or end a call. MUTE Press to mute the microphone during a call. Press to mute the ringer in the earpiece when there is an incoming call. VOL+/VOLSlide the volume switch to the right or left to adjust the headset ringer volume while in idle mode, or the listening volume while on a call.
Quick reference guide - headset charger Magnetic charging mount Place the headset here for charging. Power cord slot Route the power cord through the slot.
Battery installation The battery is permanently attached to the battery compartment cover. Do not try to separate them from each other. After installing the battery, charge it for at least 15 minutes. You may be able to make and receive short calls. For optimal performance, charge the headset battery for at least three hours before use. When fully charged, the headset battery provides approximately 12 hours of talk time or 5 days of standby time.
Headset charger installation and battery charging After installing the battery, charge the headset by placing it in the magnetic charging mount as shown below. The light turns on when the headset is charging. . Plug the small end of the headset charger power adapter into the power jack at the bottom of the headset charger. Route the power cord through the power cord slot. Plug the large end of the power adapter into an electrical outlet not controlled by a wall switch. .
Adding and registering headsets You must register your new TL7800 headset with one of the following devices before use: • AT&T TL7810/TL7812 cordless headset (see page 6). You can register a maximum of two headsets to each headset base. • Synapse SB67030/SB67031 deskset (see page 7). • SynJ SB67138/SB67158 base (see page 8). • A compatible AT&T DECT 6.0 cordless telephone (see pages 9-10). Visit www.smbtelephones.att.com/compatibility-finder for a list of compatible telephones.
Adding and registering headsets Register a headset to the TL7810/TL7812 headset base . Make sure the battery is properly installed in the headset (see page 3). The light flashes slowly in red and blue to indicate the headset is not registered. . Place the headset in the headset charger and allow it to charge for at least one hour before beginning registration. . Remove the headset from the headset charger. .
Adding and registering headsets Register a headset to the Synapse SB67030/SB67031 deskset Press MENU on the deskset. Scroll to User Settings, then press SELECT. Scroll to Cordless Settings, then press SELECT. Scroll to Headset, then press SELECT. Make sure the screen shows Cordless Headset is currently Not Registered before registration. 5. On the deskset, press Register. The screen displays Registration in Progress... while the deskset is searching for the headset. 6.
Adding and registering headsets Register a headset to the SynJ SB67138/SB67158 base . Place the headset in the headset charger and allow it to charge for at least five minutes before beginning registration. Make sure the headset is out of the headset charger before you begin registration. . On the telephone base, press MENU. . Scroll down to Registration and then press ENTER. . Press ENTER again to select Register HS. The telephone base shows Registering new device... 5.
Adding and registering headsets Register a headset to an AT&T DECT cordless telephone base . Make sure the battery is properly installed in the headset (see page 3). The light on the headset flashes slowly in red and blue to indicate the headset is not registered. . Place the headset in the headset charger and allow it to charge for at least one hour before beginning registration. . Remove the headset from the charger. .
Adding and registering headsets Register a headset to an AT&T DECT cordless telephone base (cont.) It takes about 60 seconds to complete the registration process. The light turns red when the headset is registered but not fully charged, or turns blue when it is registered and fully charged. To verify the registration, press the button on the headset and check for a dial tone. If the registration fails, you hear the voice prompt "Not registered" and the light on the headset flashes slowly in red and blue.
Headset attachments Earbud There are a total of six earbuds provided. One of them has been attached to the headset. They come in three sizes of which there are two types: one normal and one providing a deeper fit. Follow the steps below to change the earbud. To remove the earbud from the headset earpiece: Hold both sides of the earbud. Twist and pull the earbud until it separates from the earpiece. To attach the earbud to the headset earpiece: . Choose an appropriate earbud. .
Headset attachments Over the ear hook There are three ear hooks provided. Choose the size that best fits your need to attach to the headset. Follow the steps below to attach an ear hook to the headset. To position the headset to wear on the left or right ear: • To wear on the left ear: . Make sure the ear hook loop is positioned, as shown in Figure 1 on the right. . Attach the ear hook to the headset, as instructed on the next page. Ear hook loop Figure 1 • To wear on the right ear: .
Headset attachments To attach the ear hook to the headset: . Make sure there is no headset attachment, except the earbud, connected to the headset. . Insert the earpiece into the ear hook loop, as shown in Figure 3. . Press the edge of the ear hook loop towards the earpiece until it clicks into place, as shown in Figure 4. 4. Hook the headset onto the desired ear. Adjust the angle of the headset until the microphone is pointing towards your mouth, as shown in Figure 5.
Headset attachments Over the head band There are two over the head bands provided. Choose the one that best fits your need to attach to the headset. Follow the steps below to attach an over the head band to the headset. To attach the head band to the headset: . Make sure there is no headset attachment, except the earbud, connected to the headset. . Insert the earpiece into the loop of the ear pad, as shown in Figure 6. . Push the earpiece into the ear pad until it clicks into place, as shown in Figure 7.
Headset attachments Behind the neck band By default, the ear pad on the neck band is positioned to be worn on the right ear. To attach the headset to the neck band: . Make sure there is no headset attachment, except the earbud, connected to the headset. . Insert the earpiece into the loop of the ear pad, as shown in Figure 9. . Gently press the earpiece inward until it clicks into place, as shown in Figure 10. . Place the neck band around your neck and over your ears. 5.
Headset operation Power on/off the headset Power on the headset before use. To power on the headset: • Place the headset in the headset charger. -OR• Press and hold for two seconds. The light flashes blue three times. You hear three beeps when it is being powered on. Power off the headset if it will not be used for a long time. To power off the headset: • Press and hold for four seconds. The light flashes red three times. You hear three beeps when it is being powered off.
www.telephones.att.com/smb © 2012-2013 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Synapse and SynJ are registered trademarks of Advanced American Telephones. Printed in China. Issue 3 AT&T 01/13.