User Manual

ManualsBrandsAt Road ManualsElectronicsMobile Internet Location MGR

Confidential Information 1 PN: 900-003x-000

@Road iLM 3100-W Series Installation Guide

Important – Please Read!

FCC RF Exposure Information

Warning: The antenna supplied with this device must be used for installation and operation.

Substitution of other antennas must be approved by the manufacturer for compliance to

radiation safety limits. The mounting of this device and antenna must be done by professional

installers to ensure that the user or nearby persons will maintain at least 20 cm from the

antenna in normal use.

Cautions: All persons must maintain a separation distance at least 20 cm from modem

antenna when transmitter is operating to meet FCC RF exposure requirements.

BEFORE THE INSTALLATION

¾ Gather Components

Please ensure you have the following items are together before beginning the installation.

There should be one complete set for each vehicle being installed. If any items are

missing, contact a local Agent or @Road immediately.

1. iLM 31XX-W Unit

2. Power Cable

3. iLM Back-Up Power Module

4. Installation Parts Kit

5. One of following Antenna options,

o Option F: Multi-band combo antenna, @Road P/N: 950-0114-000

o Option A: Dual PCS/CELL , @Road P/N: 950-0114-000

Following the simple steps below will ensure

optimum performance of your iLM unit.

Should you have questions, please contact

@Road Customer Service toll-free at

1-877-4-AtRoad (1-877-428-7623).

Summary of content (11 pages)

PAGE 1
@Road iLM 3100-W Series Installation Guide Important – Please Read! Following the simple steps below will ensure optimum performance of your iLM unit. Should you have questions, please contact @Road Customer Service toll-free at 1-877-4-AtRoad (1-877-428-7623). FCC RF Exposure Information Warning: The antenna supplied with this device must be used for installation and operation. Substitution of other antennas must be approved by the manufacturer for compliance to radiation safety limits.
PAGE 2
5. Installation Information Sheet, 4 part carbon (packaged with iLM Unit) ¾ BEFORE YOU CONTINUE Verify/Match Unit to Correct Vehicle NOTE: Some iLM’s are pre-matched to vehicle by number. This must be known before beginning the installation. 1) Check with the customer to see if vehicles were pre-matched by name/VIN/Serial Number. 2) Fill out the Installation Information Sheet noting iLM ID’s to Vehicles by VIN, License or Car Number. This information is required for the customer to track their vehicles.
PAGE 3
BEGINNING THE INSTALLATION 1) Choose a Location Determine the best location to install the iLM unit.
PAGE 4
on both the RED and WHITE power connections with the 10 amp fuses and fuse holders, included in the installation kit. Additionally, remember to place the tamper resistant sticker and a tie wrap over the cover of the fuse holder, as shown in the following picture, so that any tampering with power source wires can be easily detected. Use a voltmeter to verify voltage and hook wires as indicated below.
PAGE 5
Special Power Requirement For European Vehicle Installation: There is a back-up power source to be installed for European Vehicle. With this it allows @Road device, iLM 3150-W, to remain in operation during voltage dip due to engine cranks. The back-up power module can be installed as shown in diagram below. Power iLM POWER CONNECTION WITH BACK-UP POWER MODULE INSTRUCTIONS: Step 1: Connect 4-Pin connector of back-up power module to EUT (iLM-W 3150) first.
PAGE 6
4) Position GPS Antenna for Optimum Performance To ensure best reception, install the GPS antenna in a location that provides a clear sky view (greater than a 90 degree angle view of the sky). Note: Mount antenna as far as possible (at least 2 feet) away from other antennas to minimize the possibility of interference.
PAGE 7
5) Connect GSM and WLAN Antenna (if separate GSM antenna or noncombo antenna) The GSM antenna should be installed in an optimum location, to intercept the cellular signals, arriving at slightly above zero degrees from the horizon. Signals will typically penetrate through non-metal material such as glass, fiberglass, and aluminum. Please refer to the illustrations below. Note: Mount antenna as far as possible (at least 2 feet) away from other antennas to minimize the possibility of interference.
PAGE 8
STEP 3: Once the unit is ON, within 15 minutes all four lights should be lit in the following: (1) Status LED: Steady GREEN. (2) WAN LED: Steady GREEN. (3) WLAN LED: - OFF: No WiFi 802.11b device is connected to it. - ON Steady: Some WiFi 802.11b device is connected to it. (4) GPS LED: Steady GREEN IMPORTANT Please allow 15 minutes for complete initialization.
PAGE 9
WAN Modem status values • • • • Registered : this is a normal operating mode. The modem has a good radio signal and is registered. Reg-wk-sig : The GSM modem is registered, and the iLM will operate normally, but the radio signal strength is marginal. This is most likely due to poor GSM coverage but could also indicate a bad/damaged GSM antenna. Good signal : The modem is not registered. The iLM will not transmit or receive data.
PAGE 10
temperature of the sensor in degrees Celsius. (To perform a rough conversion from Celsius to Fahrenheit multiply by 2 and add 32. E.g. 25 C is approximately 82 F). How to Contact @Road US Support and Service Voice: 1-877-428-7623 Fax: 1-510-353-1442 Email: support@road-inc.com Web site: http://www.road.com At Road, Inc. Headquarters 47200 Bayside Parkway Fremont, CA 94538 Tel: 510.668.1638 Fax: 510.353.6021 Toll Free: 1.877.4AtRoad Find @Road on the World Wide Web at: http://www.road.
PAGE 11
The @Road devices, products and services and any modifications, alterations, additions or changes to the devices, products or services, are not fault tolerant and are not designed, manufactured or intended for use in life support, emergency, mission critical or other ultra-hazardous activities (“High Risk Activities”). @Road specifically disclaims any express or implied warranty of fitness for such High Risk Activities.