Quick Installation Guide Applicable Models: AS1002T/AS1002Tv2/AS1004T/AS1004T v2 Ver.2.3.0903 (2015-3-2) Ver.3.2.
Table of Contents Notices .................................................................................................................................... 3 Safety Precautions .................................................................................................................. 4 1. Package Contents .............................................................................................................. 5 2. Optional Accessories ..........................................................
Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Safety Precautions The following safety precautions will increase the life of the NAS. Follow all precautions and instructions. Electrical Safety Unplug this product from the power source before cleaning. Use only the bundled power adapter. Using other power adapters may damage your device. Ensure that you plug the power adapter to the correct power input rating. Check the label on the power adapter for the power rating. Operation Safety DO NOT place this product in a location where it may get wet.
1.
x8 x16 x1 x1 Screws for use with 3.
2. Optional Accessories The items below may be purchased from the ASUSTOR Accessories Store http://shop.asustor.com.
3. Hardware Installation Guide All data stored on the hard disk(s) will be erased and CANNOT be recovered. Please back up all important data before initializing the system. Tools Needed for Hard Disk Installation At least one 3.5 inch SATA hard disk. (For a list of compatible hard disks, please see http://www.asustor.com/service/hd?id=hd) Hard Disk Installation 1. Remove the screws from the rear of the NAS as shown in the graphic below. AS1002T / AS1002T v2 AS1004T / AS1004T v2 2.
AS1002T / AS1002T v2 AS1004T / AS1004T v2 3. Installing 3.5 inch hard disks: Slide the hard disks all the way into the disk bay until they are firmly seated and connected with the SATA connector. For 3.5” drives with 3 screw holes on each side.
AS1004T / AS1004T v2 Note: Please insert the hard disk into the HDD 1 slot shown in the graphic in order to have it initialized. For 3.5” drives with 2 screw holes on each side.
Note: Please insert the hard disk into the HDD 1 slot shown in the graphic in order to have it initialized. 4. Secure each hard disk with the screws provided as shown in the graphic below. For 3.5” drives with 3 screw holes on each side. AS1002T / AS1002T v2 Note: If you wish to utilize the RAID function, it is recommended that you use hard disks of the same capacity in order to fully utilize the capacity of all hard disks.
Note: If you wish to utilize the RAID function, it is recommended that you use hard disks of the same capacity in order to fully utilize the capacity of all hard disks. AS1004T / AS1004T v2 Note: If you wish to utilize the RAID function, it is recommended that you use hard disks of the same capacity in order to fully utilize the capacity of all hard disks. 5. Replace the cover and tighten the screws that were removed previously.
Securing the Power Cord Note: You can use the provided cord bracket to secure the power cord in place, if you are concerned about the NAS power cord becoming detached when the NAS is moved. 1. Take the cord bracket out of the accessories box. 2. Attach the bracket to the power cord as shown in the graphic below. 3. Remove the fan screw by unscrewing it counter-clockwise. AS1002T / AS1002T v2 AS1004T / AS1004T v2 4. Position the bracket over the hole for the removed fan screw.
AS1004T / AS1004T v2 Connecting and Powering on the NAS 1. Connect the NAS to its power supply. 2. Connect the NAS to your router, switch or hub using an Ethernet cable. 3. Press and hold down the power button located on the back of the device for 1 – 2 seconds until the yellow power LED indicator is lit. This indicates that the NAS is now powered on. While the NAS is being powered on, the yellow system status LED indicator will flash and the yellow network LED indicator will be lit as well. 4.
4. Software Installation Guide There are 4 different installation methods that you can choose from. Please select the method most suitable for you. You can go to the download section of the ASUSTOR website (http://www.asustor.com/service/downloads) to download the latest software. Download Center Installation Windows Users 1. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for ASUSTOR NAS devices. 2.
Mac Users 1. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for ASUSTOR NAS devices. 2. Select your NAS from the list and follow the installation wizard’s instructions to complete the configuration process.
Web Installation 1. If you already know your NAS’s current IP address, you can open up a web browser and enter in your NAS’s IP address (for example: http://192.168.1.168:8000) to begin initialization. 2. Please follow the instructions from the installation wizard to complete the configuration process.
Installation Using a Mobile Device 1. Search for “AiMaster” in Google Play or the Apple App Store. You can also scan the QR codes provided below. Download and install the AiMaster mobile app to your mobile device. AiMaster for Android AiMaster for iOS 2. Make sure that your mobile device is connected to the same local network that your NAS is connected to. 3. Next, open AiMaster and then select the [ + ] icon from the toolbar at the top of the screen. 4. Select [Auto Discovery].
5. Select your NAS from the list that appears. 6. Select [Start Initialization] to begin installation. Follow the prompts and instructions to complete the configuration process.
Installation Using a Direct Connection Please see section Troubleshooting for installation instructions. Shutting Down Your NAS Hold down the power button for 1.5 seconds. You should be able to hear a “beep” from the system buzzer. Let go of the power button and the NAS will either shut down or enter sleep mode depending on your configuration.
5.Appendix LED Indicators AS1002T/AS1002T v2/AS1004T/AS1004T v2 1. 2. 3. 4. Power LED Indicator System Status LED Indicator Network LED Indicator Hard Disk LED Indicator LED Indicator Color Description State Power Yellow Steadily lit Power on Orange Flashes every 10 seconds LED night mode Flashing Powering on Steadily lit System ready System Status Yellow 1. System or hard disk abnormality Red Steadily lit 2.
Rear Panel 1. Power Button 2. Reset Button 3. USB 3.0 Port 4. 5. 6. 7. Network Port DC Input K-Lock System Fan Troubleshooting Q: Why can’t I detect my ASUSTOR NAS using ASUSTOR Control Center? A: If you are having trouble detecting your NAS using ASUSTOR Control Center, please do the following: 1. Please check your network connection: Make sure that your computer and your NAS are part of the same local area network. Check to see if the network LED indicator is lit.
Click on [Change adapter settings] in the left hand panel.
Right-click on [Local Area Connection] and select [Properties]. Under the [Networking] tab select [Internet Protocol Version 4 (TCP/IPv4)] and click on [Properties].
Under the [General] tab select the [Use the following IP address] radio button. Set the [IP address] to 169.254.1.1 and the [Subnet mask] to 255.255.0.0 and then click on [OK]. Open up ASUSTOR Control Center to scan for your NAS. s 4. If the above mentioned procedures have not managed to solve your problem, please contact your local ASUSTOR dealer or ASUSTOR Customer Service http://support.asustor.com.You are also encouraged to browse through the ASUSTOR Knowledgebase.
