Quick Installation Guide Applicable Models AS3302T/AS3304T Ver.2.3.0903 (2015-3-2) Ver. 4.0.
Table of Contents Notices ..................................................................................................................................................... 3 Safety Precautions ................................................................................................................................... 4 1. Package Contents ................................................................................................................................ 5 2. Optional Accessories ......
Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Safety Precautions The following safety precautions will increase the life of the NAS. Follow all precautions and instructions. Electrical Safety Unplug this product from the power source before cleaning. Use only the bundled power adapter. Using other power adapters may damage your device. Ensure that you plug the power adapter to the correct power input rating. Check the label on the power adapter for the power rating. Operation Safety DO NOT place this product in a location where it may get wet.
1. Package Contents Applicable Models: AS3302T, AS3304T Model Name AS3302T AS3304T x1 x1 x1 x1 x1 x1 x8 x16 x1 x1 Power Cord Adapter RJ45 Network Cable Screws for use with 2.
2. Optional Accessories The items below may be purchased from the ASUSTOR Accessories Store http://shop.asustor.com.
3. Hardware Installation Guide All data stored on the hard disk(s) will be erased and CANNOT be recovered. Please back up all important data before initializing the system. Tools Needed for Hard Disk Installation Phillips head screwdriver At least one 2.5 or 3.5 inch SATA hard disk. (For a list of compatible hard disks, please see http://www.asustor.com/service/hd?id=hd) Hard Disk Installation 1. Remove the front panel as shown in the image below. AS3302T 2.
To install a 2½ " hard drive, please remove the two rails on both sides of the hard drive tray. Align the hard drive with the 4 holes labeled 2.5" with the SATA connector facing outward. While maintaining a grip on the hard drive and tray, turn the tray upside down and secure the drive with four included M3 screws as demonstrated below. 4. Slide the disk tray onto the rails of the disk bay. Using the latch, gently push the disk tray all the way into the disk bay.
AS3302T AS3304T Securing the Power Cord Note: You can use the provided cord bracket to secure the power cord in place, if you are concerned about the NAS power cord becoming detached when the NAS is moved. Attach the bracket to the power cord as shown in the graphic below. AS3302T AS3304T Connecting and Powering on the NAS 1. Connect the NAS to its power supply.
2. Connect the NAS to your router, switch or hub using an Ethernet cable. 3. Press and hold down the power button for 1 – 2 seconds until the blue power LED indicator is lit. This indicates that the NAS is now powered on. While the NAS is being powered on, the green system status LED indicator will flash and the blue network LED indicator will be lit as well. AS3302T 4. AS3304T The NAS is ready for operation once the green system status LED indicator has stopped flashing and remains steadily lit.
4. Software Installation Guide There are 4 different installation methods that you can choose from. Please select the method most suitable for you. You can go to the download section of the ASUSTOR website (http://www.asustor.com/service/downloads) to download the latest software. Download Center Installation Windows Users 1. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for ASUSTOR NAS devices. 2.
Mac Users 1. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for ASUSTOR NAS devices. 2. Select your NAS from the list and follow the installation wizard’s instructions to complete the configuration process.
Web Installation 1. If you already know your NAS’s current IP address, you can open up a web browser and enter in your NAS’s IP address (for example: http://192.168.1.168:8000) to begin initialization. 2. Please follow the instructions from the installation wizard to complete the configuration process.
Installation Using a Mobile Device 1. Search for “AiMaster” in Google Play or the Apple App Store. You can also scan the QR codes provided below. Download and install the AiMaster mobile app to your mobile device. AiMaster for Android AiMaster for iOS 2. Make sure that your mobile device is connected to the same local network that your NAS is connected to. 3. Next, open AiMaster and then select the [ + ] icon from the toolbar at the top of the screen. 4. Select [Auto Discovery].
5. Select your NAS from the list that appears.
6. Select [Start Initialization] to begin installation. Follow the prompts and instructions to complete the configuration process. Installation Using a Direct Connection Please see section Troubleshooting for installation instructions. Shutting Down Your NAS 1. Confirm the function settings for the power button as shown in the graphic below. When the power button is held down for 1.5 seconds you can decide whether to shut down the NAS or have it enter into sleep mode.
2. Hold down the power button for 1.5 seconds. You should be able to hear a “beep” from the system buzzer. Let go of the power button and the NAS will either shut down or enter sleep mode depending on your configuration.
5. Appendix LED Indicators AS3302T AS3304T Power LED Indicator USB LED Indicator System Status LED Indicator Hard Disk LED Indicator Network LED Indicator LED Indicator Color Description State Blue Steadily lit Power on Orange Flashes every 10 seconds LED night mode Flashing Powering on Steadily lit System ready Blue Steadily lit 1 Gigabit Network port connected Purple Steadily lit 2.
USB Steadily lit The USB device connected to the front of the NAS is ready for use Flashing Data access in progress Steadily lit Hard disk ready Flashing Data access in progress Steadily lit Hard disk abnormality Green Green Hard Disk Red Rear Panel AS3302T AS3304T USB 3.2 Gen 1 Port DC Input 2.
1. Please check your network connection: Make sure that your computer and your NAS are part of the same local area network. Check to see if the network LED indicator is lit. If you find that it is not lit, try connecting your Ethernet cable to the other network port or try using a different Ethernet cable. 2. Please first disable any firewalls that may be running on your computer. Then try scanning for your NAS again using ASUSTOR Control Center. 3.
Under the [Networking] tab select [Internet Protocol Version 4 (TCP/IPv4)] and click on [Properties]. Under the [General] tab select the [Use the following IP address] radio button. Set the [IP address] to 169.254.1.10 and the [Subnet mask] to 255.255.0.0 and then click on [OK].
Open up ASUSTOR Control Center to scan for your NAS.
4. If the above mentioned procedures have not managed to solve your problem, please contact your local ASUSTOR dealer or ASUSTOR Customer Service http://support.asustor.com.You are also encouraged to browse through the ASUSTOR Knowledgebase.
