802.11b Guide FCC RF EXPOSURE INFORMATION ( 802.11b Wireless LAN) In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
Copyright© 2002 Intel Corporation. Back to Contents Installation under Windows XP Preliminary Notes The installation instructions in this section are based on the following assumptions: • • • The Intel(R) PRO/Wireless LAN Mini PCI Adapter hardware has already been installed in the computer in accordance with the computer manufacturer's instructions. The computer has not been powered on since the hardware installation was completed. No other wireless LAN card is installed in this computer.
6. On the Data Encryption screen, click Next to accept the default encryption setting None, or enter specific encryption settings for your network, then click Next. 7. On the Found New Hardware Wizard screen, click Finish. Proceed to disable the Windows XP wireless configuration feature.
Continue with the following steps to install the Intel(R) Wireless Administration Tools Site Survey and AP Discovery (optional): Some versions of this product do not support the Intel(R) PRO Network Connections menu screen for installation of the Administration Tools. If the Intel(R) PRO Network Connections menu screen does not appear, or if it does not have a menu item for Wireless LAN Adapters, you can start the Administration Tools installer manually using Start > Run and browsing to the file APAdmin.
After loading the Windows 2000 operating system, be sure to log in with administrative rights. If you log in to Windows 2000 without administrative rights, you may run into problems during the installation. During initial adapter installation and configuration, it may take up to two minutes for adapter settings to be confirmed. Driver Installation To install driver software in Windows* 2000, follow these steps: 1.
14. On the License Agreement screen, after reading the license agreement, select I accept the terms in the license agreement and click Next. 15. On the Setup Type screen, verify that Typical is selected, then click Next. This is the recommended setting for a first-time installation. 16. On the Ready to Install the Program screen click Install. 17. After the software is installed on your computer, click Finish.
Installation under Windows Me Preliminary Notes The installation instructions in this section are based on the following assumptions: • • • The Intel(R) PRO/Wireless LAN Mini PCI Adapter hardware has already been installed in the computer in accordance with the computer manufacturer's instructions. The computer has not been powered on since the hardware installation was completed. No other wireless LAN card is installed in this computer.
. Display the Intel(R) PRO Network Connections screen by removing and re-inserting the Intel CD, or by running autorun.exe from the CD. Click Wireless Adapters. 9. On the Intel PRO/Wireless LAN Adapters menu screen, click Install Software. 10. On the Welcome to the InstallShield Wizard for Intel(R) PROSet II screen, click Next. 11. On the License Agreement screen, after reading the license agreement, select I accept the terms in the license agreement and click Next. 12.
Preliminary Notes The installation instructions in this section are based on the following assumptions: • • • The Intel(R) PRO/Wireless LAN Mini PCI Adapter hardware has already been installed in the computer in accordance with the computer manufacturer's instructions. The computer has not been powered on since the hardware installation was completed. No other wireless LAN card is installed in the computer. To install the driver before installing hardware, use Start > Run and browse to the file SetupWLD.
13. On the Setup Type screen, select Typical and then click Next. This is the recommended setting for a first-time installation. 14. On the Ready to Install the Program screen click Install. 15. After the software is installed on your computer, click Finish. 16. When prompted to restart the computer, click Yes. 17. To launch Intel PROSet, double-click the PROSet icon in the system tray or follow the path Start > Programs > Intel Network Adapters > Intel(R) PROSet.
• • • • Deleting a Profile Connecting to a Network without a Profile Profile Connection Preferences Loading a Profile from the Task Tray A profile is a saved group of network settings. Profiles are displayed in the Profile List in the PROSet General page. Profiles can be arranged in order of network connection priority. You can connect to one network using the first profile in the Profile List, then automatically connect to another network using the next profile.
11. Use these options to configure TCP/IP and VPN settings for a VPN profile. Click Next when finished. Step 3 of 4: Security Settings 12. Select Open or Shared in the Network Authentication drop-down menu. Open, does not use any authentication method. Shared uses the WEP key as the authentication method. 13. Click the Enable data encryption (WEP) checkbox to configure WEP encryption settings. 14. Click the Password protect this profile checkbox to assign a password to the profile. 15. Click Next.
Important: Only password protected profiles can be imported and exported. Refer to Setting a Profile Password for more information. To import profiles: 1. 2. 3. 4. 5. From the General page, click the Networks tab. Click the Advanced button. Click the Import/Export button. Click the Import button. Locate the profile to import on your hard disk or enter the profile name in the File name field. The profile extension is .profile. 6. Click the Import to import the profile into the Profile List. 7.
Editing an Existing Profile To edit an existing profile: 1. 2. 3. 4. 5. 6. 7. 8. 9. Select the wireless adapter in the left-side pane. From the General page, click the Networks tab. Click the Edit button. The General page displays. Click on the General, Security, Network and Password tabs to make the necessary changes for the network profile settings: Click OK on any of the pages to save all the settings and return to the Networks page. Click the new profile name shown in the Profile List.
4. Click OK to save the setting and return to the previous dialog. Loading a Profile from the Task Tray To load a profile from the Task Tray: 1. Right-click PROSet icon in the task tray. 2. Select the Intel PRO/Wireless LAN 7100 3B Mini PCI Adapter. 3. Click Select Profile and select the profile to be launched. Back to Contents Page Copyright© 2002 Intel Corporation.
The Configuration Service can be used in two ways: • • To connect using preferred profiles only. In this mode the Configuration Service will attempt to connect to a network access point using the Profile List only. If a matching profile is not found, a dialog appears that lists available networks. From this dialog you can connect to any available network. You can also close this dialog without connecting by clicking the Cancel button.
• The buttons described above will not be disabled if you click the message: Another wireless LAN utility is communicating with the Intel PRO/Wireless LAN Adapter. To avoid conflicts, PROSet has temporarily disabled its Profile Management features. Scanning for Available Networks A fast way to connect to a network is to use the Scan button to search for a network access point in range of your wireless adapter. When a network is found, you can instantly connect without a profile or create a new profile.
8. Click the Configure TCP/IP and VPN settings check box and click the Next button to access the TCP/IP and VPN settings. If these settings are not required, leave the box unchecked and proceed to step 11. 9. Click the Next button to select the WEP security settings. 10. Click the Password protect this profile checkbox and click Next button to access the Password Protection settings. Click Finish after the password information has been entered.
Creating an Ad Hoc Profile Using the Profile Wizard The following describes how to create a new ad hoc profile using the Profile Wizard and connect to an ad hoc network. You can also connect to a network, by using the Scan button. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. From the General page, select the wireless adapter on the left side pane. Click the Networks tab. Click the Add button. Enter the profile name in the text box. Enter a network name (SSID) in the text box.
9. Under Send Files, files can be sent to another computer in the ad hoc network. To send a file, click the Send File button. Locate the file you want to sent, and click Send. 10. Click the Close button to end the ad hoc session. Disconnecting from a Network To disconnect from a network, turn the radio to OFF from the General page in PROSet. Switching the Adapter Off and On When your laptop is switched on, the adapter radio is constantly transmitting signals.
