User Manual

ManualsBrandsAsus ManualsMini PCsVivoMini UN62V

E9955

Revised Edition V2

December 2014

VivoMini memory, wireless card, and

solid state drive (SSD) installation guide

Your VivoMini comes with two SO-DIMM memory slots that allow you to install two 2GB, 4GB, or

8GB unbuered with non-ECC 1.35 V DDR3 204-pin SO-DIMMs for a maximum of 16GB memory.

IMPORTANT! Refer to http://www.asus.com for the list of compatible DIMMs. You can only

install 1.35 V DDR3 SO-DIMM to the VivoMini’s DIMM slots.

IMPORTANT!

• Itisrecommendedthatyouinstallorupgradethememorymodules,wirelesscard,and

solid state drive (SSD), under professional supervision. Visit an ASUS service center for

further assistance.

• Ensurethatyourhandsaredrybeforeproceedingwiththerestoftheinstallation

process.Beforeinstallinganyofthefeaturesinthisguide,useagroundedwriststrapor

touchasafelygroundedobjectormetalobjecttoavoiddamagingthemduetostatic

electricity.

Installing or upgrading memory modules

To install or upgrade the memory modules:

1. Turn o your VivoMini then disconnect all cables and peripherals.

2. PlacetheVivoMinionaatstablesurface,withitstopsidefacingdown.

YourVivoMinicomeswiththefollowingitems.PleasecontactASUSServiceCenterifyoucannot

ndthefollowingitems:

• 4pcsholedrubberfoot

• 3pcs3mmroundscrews,1hexagonscrew

15060-47900100

Summary of content (8 pages)

PAGE 1
Revised Edition V2 December 2014 E9955 VivoMini memory, wireless card, and solid state drive (SSD) installation guide Your VivoMini comes with the following items. Please contact ASUS Service Center if you cannot find the following items: • 4 pcs holed rubber foot • 3 pcs 3mm round screws, 1 hexagon screw IMPORTANT! • It is recommended that you install or upgrade the memory modules, wireless card, and solid state drive (SSD), under professional supervision.
PAGE 2
3. Remove the four screws securing the cover. 4. Get one screw from the ones you previously removed then place it into the hole. Leave a portion of the screw head that would be enough for you to hold. 5. Hold the screw then gently pull out the cover from the bottom side of the VivoMini. Use your other free hand to hold the VivoMini in place.
PAGE 3
6. Align and insert the memory module into the slot (A) and press it down (B) until it is securely seated in place. Repeat the same steps to install the other memory module. IMPORTANT! Always install into the lower slot first. 7. Remove the screw you previously attached on the bottom cover. 8. Place the cover back on the bottom side of your VivoMini. Note that the cover can only be inserted in one direction.
PAGE 4
9. 10. Reattach the screws to secure the cover back on the bottom side of the main box. Place the rubber foot on each screw hole. Refer to the illustration for more details. IMPORTANT! A number is printed under each rubber foot and this number corresponds to that rubber foot’s location on the cover. Follow the orientation of each rubber foot and the number sequence shown in the illustration below. The rubber foot fits in only one orientation.
PAGE 5
Installing or upgrading the wireless card Your VivoMini includes a mini-PCIe slot for half-size wireless and Bluetooth adapters. Refer to http://www.asus.com for the list of compatible wireless and Bluetooth adapters. To install or upgrade the wireless card: 1. Follow steps 1-5 on pages 1-2 under the Installing or upgrading memory modules section of this guide to remove the bottom cover of your VivoMini. 2. Align and insert the wireless card into the lower slot inside the VivoMini.
PAGE 6
4. Connect the black antenna to MAIN or and the white antenna to AUX or to the illustration for the right installation procedure. . Refer NOTE: A soft clicking sound indicates that the antenna has been securely attached on the wireless card. 5. Follow steps 7-9 on pages 3-4 under the Installing or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini.
PAGE 7
2. Align and insert the full-size mSATA SSD into its the upper slot inside the VivoMini. Refer to the illustration for its location. 3. Gently push down the mSATA SSD on top of the screw hole and fasten it using one of the 3mm round screw. Refer to the illustration for the location of the screw hole. 4. Follow steps 7-9 on pages 3-4 under the Installing or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini.
PAGE 8
2. Insert the hexagon screw into its corresponding hole, as illustrated. 3. Align and insert the half-size mSATA SSD into its upper slot inside the VivoMini. Refer to the illustration for its location. 4. Gently push down the mSATA SSD on top of the screw hole and fasten it using one of the 3mm round screw. Refer to the illustration for the location of the screw hole. 5.