Installation Guide

2 3 4 5 6
E10670
Revised Edition V3
October 2015
VivoMini memory, wireless card, and
solid state drive (SSD) installation
guide
IMPORTANT!
• Itisrecommendedthatyouinstallorupgradethememorymodules,wireless
card,andsolidstatedrive(SSD),underprofessionalsupervision.VisitanASUS
servicecenterforfurtherassistance.
• Ensurethatyourhandsaredrybeforeproceedingwiththerestoftheinstallation
process.Beforeinstallinganyofthefeaturesinthisguide,useagroundedwrist
straportouchasafelygroundedobjectormetalobjecttoavoiddamagingthem
duetostaticelectricity.
YourVivoMinicomeswiththefollowingitems.PleasecontactASUSServiceCenterifyoucannot
ndthefollowingitems:
• 4pcsholedrubberfoot
• 2pcs2mmroundscrews,1hexagonscrew
• 4pcs3mmroundscrews,4pcs2mmroundscrews(onselectedmodels)
• 2pcsHDDbracket(onselectedmodels)
• 1pcHDDcable(onselectedmodels)
1
15060-64610000
3. Removethefourscrewssecuringthecover.
To install or upgrade the memory modules:
1. TurnoyourVivoMinithendisconnectallcablesandperipherals.
2. PlacetheVivoMinionaatstablesurface,withitstopsidefacingdown.
YourVivoMinicomeswithtwoSO-DIMMmemoryslotsthatallowyoutoinstalltwo2GB,4GB,
or8GBunbueredwithnon-ECC1.35VDDR3L204-pinSO-DIMMsforamaximumof16GB
memory.
Installing or upgrading memory modules
IMPORTANT! Refertohttp://www.asus.comforthelistofcompatibleDIMMs.Youcan
onlyinstall1.35VDDR3LSO-DIMMtotheVivoMini’sDIMMslots.
NOTE:
• TheCPUmodelN3000onlyhasoneDIMMslot.
• Somemodelsmayonlysupportuptoamaximumof8GBmemory
NOTE: Theillustrationsinthisguideareforreferenceonly.Theslotsmayvary
dependingonmodel.
4. Getonescrewfromtheonesyoupreviouslyremovedthenplaceitintothehole.Leave
aportionofthescrewheadthatwouldbeenoughforyoutohold.
5. HoldthescrewthengentlypulloutthecoverfromthebottomsideoftheVivoMini.Use
yourotherfreehandtoholdtheVivoMiniinplace.
7. Removethescrewyoupreviouslyattachedonthebottomcover.
6. Alignandinsertthememorymoduleintotheslot(A)andpressitdown(B)untilitis
securelyseatedinplace.Repeatthesamestepstoinstalltheothermemorymodule.
IMPORTANT!Alwaysinstallintotheupperslotrst.
NOTE: TheCPUmodelN3000onlyhasoneDIMMslot.
8. PlacethecoverbackonthebottomsideofyourVivoMini.Notethatthecovercanonly
beinsertedinonedirection.Refertothefollowingillustrationandnotetoensurethat
thecoverissecurelyttedonthebottomsideoftheVivoMini.
IMPORTANT!Theratinglabelarea(A)andthepowerbutton’slocation(B)mustbe
orientedasshown.
9. Reattachthescrewstosecurethecoverbackonthebottomsideofthemainbox.
10. Placetherubberfootoneachscrewhole.Refertotheillustrationformoredetails.
IMPORTANT! Anumberisprintedundereachrubberfootandthisnumber
correspondstothatrubberfoot’slocationonthecover.Followtheorientationofeach
rubberfootandthenumbersequenceshownintheillustrationbelow.Therubber
foottsinonlyoneorientation.Notethepositionoftheholeoneachrubberfoot,as
shownintheillustrationbelow
NOTE:Ifyouwanttoremovetherubberfoot,useaatheadscrewdriverora
straightenedpapercliptodoso.
E10670_VivoMini_Memory_SSD_WiFi_installation_V3_fold.indd 1-6 2015/10/21 �� 04:55:10