Tinker Board 2 Series User Manual
E17169 First Edition March 2021 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Conventions used in this manual......................................................................................................................................................................4 Typography...............................................................................................................................................................................................................4 Chapter 1: 1.1 1.2 1.3 1.4 1.5 1.6 Specifications Summary Introduction............
Conventions used in this manual To highlight key information in this manual, some text are presented as follows: IMPORTANT! This message contains vital information that must be followed to complete a task. NOTE: This message contains additional information and tips that can help complete tasks. WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Single Board Computer's data and components.
Product Overview 1
1.1 Introduction Tinker Board 2 Series is more than a dream for the DIY-obsessed: it’s a gateway to new ideas and new relationships. Experienced makers will love Tinker Board’s performance-to-price ratio and strong brand heritage, while novices and younger users will appreciate its accessibility and ease of use. But all will come together to create — Together We Make! 1.
1.4 Product specification SoC CPU GPU Display Memory Size Storage Connectivity Audio USB Camera Interface Internal Headers Power Connector (up to 45W) Environment OS Support Dimension Tinker Board 2 Tinker Board 2S Rockchip RK3399 (64-bit) Dual-core Arm® Cortex®-A72 @ 2.0 GHz Quad-core Arm® Cortex®-A53 @ 1.5 GHz Arm® Mali™-T860 MP4 GPU @ 800 MHz 1 x HDMI™ with CEC hardware ready 1 x USB Type-C® (DP 1.
1.5 Dimensions (mm) Front Top Left Right Rear 1.
Product Introduction 2
2.1 Before you proceed Take note of the following precautions before you install your Single Board Computer components or change any single board computer settings. NOTE: The diagrams in this chapter are for reference only. The Single Board Computer layout may vary with models. IMPORTANT! Components shown in this section may be purchased separately. Refer to Package contents section for more information about the contents of your Single Board Computer package.
2.2 Single board Computer layout Top view Bottom view * eMMC is only available on selected models. Layout contents 1. GPIO header 2. SOC RK3399 3. Debug UART header 4. Reset header 5. MIPI DSI connector 6. DC Fan header 7. Power-on header and Maskrom jumper 8. Status LEDs 9. MIPI CSI-2 connector 10. RTC Battery header 11. M.2 Wi-Fi slot 12.
1. GPIO header This 40-pin GPIO (General-Purpose Input/Output) header can be designated (in software) as an input or output pin and is used for a wide range of purposes. Of the 40 pins, 28 are GPIO pins (shared with SPI/ UART/I2C pins). 40P_GPIO 2 1 4 3 6 5 8 7 12 16 20 24 28 32 36 40 10 14 18 22 26 30 34 38 9 13 17 21 25 29 33 37 11 15 19 23 27 31 35 39 Tinker Board 2 / 2S 40-pins GPIO header Pin definition VCC3.
2. SOC RK3399 This ARM® system on a chip (SoC) features the new 64-bit Armv8 architecture and Arm® big.LITTLE™ technology’s 6-core processor, provides improved performance and comes bundled with Arm® Mali®-T860 MP4 GPU. 3. Debug UART header This Debug UART header provides a separate UART port, allowing developers to use and develop with the serial console without occupying the 40-pin GPIO’s UART ports. Dimension 2.54 4. Reset header The Reset header allows you to connect an external reset button.
5. MIPI DSI connector The MIPI DSI connector is used to connect a MIPI display module via a 4 lane MIPI-DSI cable. This connector supports up to 6 Gbps connection speed. 6. DC Fan header The DC Fan header allows you to connect a fan to actively cool the system. Connector Type Reference PN: JST PH 2P 2.00mm JST, PHR-2 NOTE: The fan is purchased separately. WARNING! • These are not jumpers! Do not place jumper caps on the fan connectors. • Ensure the cable is fully inserted into the connector.
7. Power On header The Power On header allows you to connect an external power button. The Maskrom jumper allows you to mask the eMMC (rom) for recovery. This will allow you to enter developer mode due to the indetected storage and rewrite the eMMC. Dimension 2.54 8. Status LEDs The Status LEDs indicate the current status of the Single Board Computer.
9. MIPI CSI connector The MIPI CSI connector is used to connect a MIPI camera module via a 2 lane MIPI-CSI2 cable. This connector supports up to 3 Gbps connection speed. WARNING! Ensure the cable for MIPI CSI is connected in the correct orientation with the gold fingers facing towards the rear of the Single Board Computer. 10. RTC Battery header The RTC Battery header allows you to connect the lithium battery. Connector Type Reference PN 16 Single Board Computer WtoB 2P 1.
11. M.2 Wi-Fi Slot (E-Key) The M.2 Wi-Fi slot allows you to install an M.2 Wi-Fi module (E-key, type 2230). NOTE: The M.2 Wi-Fi module is purchased separately on selected models. 12. Micro SD Card slot The microSD card slot allows you to install a microSD memory card v2.00 (SDHC) / v3.00 (SDXC) for storage. WARNING! Disconnect all power (including redundant PSUs) from the existing system before you add or remove a memory card, then reboot the system to access the memory card.
2.3 I/O connectors 2.3.1 Left panel 1. DC Power Input Jack The supplied power adapter converts AC power to DC power for use with this jack (5.5mm/2.5mm). Power supplied through this jack supplies power to the Single Board Computer. To prevent damage to the Single Board Computer, always use the supplied power adapter. Please refer to the table below for the power consumption. Power Consumption Mode Suspend Idle Burn-in* Max. Load** Power (W) 0.44 3.65 8.18 29.18 * CPU, GPU, RAM, Storage, LAN, etc.
2.3.2 Rear panel 1. LAN (RJ-45) port The 8-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network. Please refer to the table below for the LED indications. 16.34±0.25 15.75±0.25 13.80±0.25 13.40±0.25 2.00±0.
2. USB 3.2 Gen 1 Type-A port The USB 3.2 Gen 1 (Universal Serial Bus) port provides a transfer rate up to 5 Gbit/s. 3. USB 3.2 Gen 1 Type-C® OTG port This USB Type-C™ (Universal Serial Bus) port provides a transfer rate of up to 5 Gbit/s 13.1 12.5±0.10 12.58 9 16.3 5 1 5.12±0.10 4 2.56±0.04 [ .101±0.02 ] 3.4 [ .134 ] 3.27 4. USB 3.2 Gen 1 Type-A port The USB 3.2 Gen 1 (Universal Serial Bus) port provides a transfer rate up to 5 Gbit/s. 13.5 12.5±0.10 12.63 18 16.34±0.25 14 10 4.
Software Installation 3
3.1 Booting from external Micro SD card Requirement: • 1 x Micro SD card with at least 8GB capacity • 1 x 12~19V, DC 5.5/2.5 power supply* • 1 x Monitor with HDMI™ cable or USB Type-C® (DP) cable • 1 x Keyboard and Mouse set * The Power Supply is purchased separately. Setting Up: 1. Insert the micro SD card into a Windows® PC. 2. Download the TinkerOS image from the Tinker Board website (https://tinker-board.asus.com/download.
Appendix
Notices Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
NCC: Taiwan Wireless Statement Contains module NCCAI18LP2010T7 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象 時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 VCCI: Japan Compliance Statement Contains module 201-180775 Class B ITE Contains module 00158-19-04076 00158-19-04076 限用物質及其化學符號: 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 印刷電路板及電子組件 - ○ ○ ○ ○ ○ 其他及其配件 - ○ ○ ○ ○ ○ 備考1.
Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/ Déclaration simplifiée de conformité de l’UE ASUSTek Computer Inc. déclare par la présente que cet appareil est conforme aux critères essentiels et autres clauses pertinentes de la directive 2014/53/EU.
تبعیت از نسخه ساده شده بیانیه اتحادیه اروپا متن کامل پیروی از. مطابقت دارد.2014/53/EU در اینجا اعالم می کند که این دستگاه با نیازهای اساسی و سایر مقررات مربوط به بیانیهASUSTek Computer Inc :این بیانیه اتحادیه اروپا در این آدرس موجود است .https://www.asus.com/support/ Απλοποιημένη Δήλωση Συμμόρφωσης ΕΕ Διά του παρόντος η ASUSTek Computer Inc. δηλώνει ότι αυτή η συσκευή είναι σύμμορφη με τις βασικές προϋποθέσεις και άλλες σχετικές διατάξεις της Οδηγίας 2014/53/ΕE.
ประกาศเกี่่ย � วกั ับความสอดคล้้องของสหภาพยุุโรปแบบย่่อ ASUSTek Computer Inc. ขอประกาศในที่่นี้้ � ว่� า่ อุุปกรณ์์นี้้มี � ค ี วามสอดคล้ ้องกัับความ ต้ ้องการที่่จำ� ำ�เป็็ นและเงื่่อ � นไขที่่เ� กี่่ย � วข้ ้องอื่่น � ๆ ของบทบััญญััติข้ ิ ้อกำำ�หนด 2014/53/EU เนื้้�อหาที่่ส � มบููรณ์์ของประกาศความสอดคล้ ้องกัับ EU มีีอยู่่�ที่ ่� https://www.asus.com/support/ Basitleştirilmiş AB Uyumluluk Bildirimi ASUSTek Computer Inc.
FCC COMPLIANCE INFORMATION Per FCC Part 2 Section 2.1077 Responsible Party: Address: Phone/Fax No: Asus Computer International 48720 Kato Rd, Fremont, CA 94538 (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Model Number : MOTHERBOARD TINKER BOARD 2, TINKER BOARD 2S compliance statement: This device complies with part 15 of the FCC Rules.