REPUBLIC OF GAMERS ROG GR8 User Guide
E9561 First Edition August 2014 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual.............................................................................................. 5 Conventions used in this manual................................................................ 5 Typography.......................................................................................................... 5 Package contents................................................................................................ 6 Getting to know your ROG GR8 Features..................
Contents Upgrading your ROG GR8 Upgrading memory modules.......................................................................32 Installing a 2.5-inch storage drive...............................................................37 Appendix Safety information............................................................................................44 Setting up your system.................................................................................44 Care during use.....................................
About this manual This manual provides information about the hardware and software features of your PC, organized through the following chapters: Chapter 1: Getting to know your ROG GR8 This chapter details the hardware components of your ROG GR8. Chapter 2: Using your ROG GR8 This chapter provides you with information on using your ROG GR8. Chapter 3: Upgrading your ROG GR8 This chapter provides information on how to upgrade the memory modules and the storage drive of your ROG GR8.
Package contents Your ROG GR8 package contains the following items: Technical documentations ROG GR8 Power cable* AC power adapter* set of screws NOTE: Actual product specifications and package contents may vary depending on your country or region. IMPORTANT! Bring the warranty card to the ASUS Service Center for replacement of the defective components if the device or its components fail or malfunction during normal and proper use within the warranty period.
1 Getting to know your ROG GR8
Features Front panel 8 ROG GR8
Power button The power button allows you to turn the ROG GR8 on or off. Miracast Receiver button The Miracast Receiver button allows you to mirror the display from other Miracast-enabled devices. Headphone jack The stereo headphone jack is used to connect the system’s audio out signal to headphones. Microphone jack The microphone jack is designed to connect the microphone used for video conferencing, voice narrations, or simple audio recordings. USB 2.
Bottom view Top view Air vents The air vents allow cooler air to enter your ROG GR8 chassis and expel hot air out. IMPORTANT! For optimum heat dissipation and air ventilation, ensure that the air vents are free from obstructions. Rubber feet The rubber feet helps prevent the ROG GR8 from slipping thus providing more stability when the ROG GR8 is in a stand-up position.
Rear panel HDD/Drive LED indicator This indicator lights up when your ROG GR8 is accessing the internal storage drives. Audio Input Jack This 1/8-inch stereo input jack can be used to connect a stereo audio source to the ROG GR8. This feature is used mainly to add audio to multimedia applications. Audio Output Jack This stereo audio jack is used to connect the system’s audio out signal to amplified speakers.
Microphone jack The microphone jack allows you to connect an external microphone for video conferencing, voice narrations, or simple audio recordings. Digital audio out port (S/PDIF optical) The Sony/Philips Digital Interface (S/PDIF) optical out port allows you to transfer digital audio from your ROG GR8 into an amplifier or your TV. HDMI port The HDMI (High Definition Multimedia Interface) port supports a Full-HD device such as an LCD TV or monitor to allow viewing on a larger external display.
Power input (DC 19V) The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the PC. To prevent damage to the PC, always use the bundled power adapter. WARNING! The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body. Cover lock latch + Kensington security slot The cover lock latch fastens the side cover on your ROG GR8.
Using your ROG GR8 2
Getting started Positioning your ROG GR8 The ROG GR8 can be positioned standing up or lying down. When positioning your ROG GR8, ensure that the rubber studs or the rubber feet are in contact with the flat and stable surface of your table or desk.
Connecting the AC power adapter To connect the AC power adapter to your ROG GR8: A. Connect the AC power cord to the AC/DC adapter. B. Plug the AC power cord into a 100V~240V power source. C. Connect the DC power connector into your ROG GR8’s power (DC) input port. NOTE: The power adapter may vary in appearance, depending on your region.
IMPORTANT! 18 ROG GR8 • We strongly recommend that you use only the AC power adapter and cable that came with your ROG GR8. • Use a grounded wall socket while using your ROG GR8. • The socket outlet must be easily accessible and near your ROG GR8. • To disconnect your ROG GR8 from its main power supply, unplug your ROG GR8 from the power socket.
Connecting a display panel You can connect a display panel or projector to your ROG GR8 that has the following connectors: • HDMI connector • DisplayPort connector • VGA connector (use with a DisplayPort to VGA adapter or HDMI to VGA adapter) • DVI connector (use with an HDMI to DVI adapter) NOTE: The HDMI to DVI adapter, DisplayPort to VGA adapter, or HDMI to VGA adapter are each sold separately.
Connecting the keyboard or mouse You can connect generally any USB keyboard and mouse to your ROG GR8. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your ROG GR8: Connect the USB cable from your keyboard and mouse to any of the USB 2.0/3.0 ports of your ROG GR8.
Turning on your ROG GR8 Press the power button to turn on your ROG GR8.
Using the Miracast Receiver The ROG GR8 allows you to mirror the display from other Miracastenabled devices or PC via the Miracast Receiver function. NOTE: The Miracast display is supported only on the HDMI port. Connecting Miracast-enabled Android device 1. Connect the bundled power adapter to your ROG GR8. 2. Press the Miracast Receiver button. NOTE: The LED on the Miracast Receiver button lights up and turns to red to indicate that the Miracast Receiver function is enabled. 3.
Connecting Windows® 8.1 / Windows 8.1 PRO devices 1. Connect the bundled power adapter to your ROG GR8. 2. Press the Miracast Receiver button. NOTE: The LED on the Miracast Receiver button lights up and turns to red to indicate that the Miracast Receiver function is enabled. 3. On your device with Windows® 8.1 / Windows 8.1 PRO OS, call out the Charms bar then select Devices. 4. Under Devices, select Project then click the SSID of ROG GR8. For Windows 8.
Connecting Intel® WiDi-supported devices 1. Turn on your ROG GR8. 2. Press the Miracast Receiver button. NOTE: The LED on the Miracast Receiver button lights up and turns to red to indicate that the Miracast Receiver function is enabled. 24 3. Launch Intel WiDi from your device. 4. From the Detected Adapters window, select the ROG GR8’s SSID then click Connect. 5. Key-in the WPS PIN shown on your TV display then click Next. 6.
Recovering your system IMPORTANT! This section only applies for models with the bundled operating system installed in your ROG GR8. Resetting your PC The Reset your PC option restores your ROG GR8 to its factory default settings. IMPORTANT! Back up all your data before using this option. To reset your PC: 1. Press during bootup. IMPORTANT! To go through POST, follow any of the ways described in the Quickly enter the BIOS section. 2. From the screen, click Troubleshoot. 3. Select Reset your PC.
Recovering from a system image file IMPORTANT! This section only applies for models with the bundled operating system installed in your ROG GR8. You can create a USB recovery drive and use this to recover your PC’s settings. Creating a USB recovery drive WARNING! All files on your USB storage device will be permanently deleted during the process. Before you proceed, ensure that you back up all your important data. To create a USB recovery drive: 26 1. Launch the Control Panel from the All Apps screen.
Removing everything and reinstalling Windows IMPORTANT! This section only applies for models with the bundled operating system installed in your ROG GR8. Restoring your ROG GR8 to its original factory settings can be done using the Remove everything and reinstall option in PC Settings. Refer to the steps below to use this option. IMPORTANT! Back up all your data before using this option. NOTE: This process may take a while to complete. 1. Launch the Charms bar. 2.
Turning off your ROG GR8 If your ROG GR8 is unresponsive, press and hold the power button for at least four (4) seconds until your ROG GR8 turns off. Putting your ROG GR8 to sleep To put your ROG GR8 on Sleep mode, press the Power button once. Entering the BIOS Setup BIOS (Basic Input and Output System) stores system hardware settings that are needed for system startup in the ROG GR8. In normal circumstances, the default BIOS settings apply to most conditions to ensure optimal performance.
Quickly enter the BIOS To quickly enter the BIOS: • Turn off your ROG GR8, then press the power button to turn your ROG GR8 back on , and then press or during POST. • When your ROG GR8 is off, disconnect the power cord from your ROG GR8’s power connector. Reconnect the power cable and press the power button to turn on your ROG GR8. Press or during POST. NOTE: POST (Power-On Self Test) is a series of software controlled diagnostic tests that run when you turn on your PC.
ROG GR8
Upgrading your ROG GR8 3
Upgrading memory modules Your ROG GR8 comes with two SO-DIMM memory slots that allow you to install up to two 8 GB DDR3L 204-pin SO-DIMMs for a maximum of 16 GB memory. IMPORTANT! You can only install DDR3L (1.35V Low Voltage) 204-pin SO-DIMM to the ROG GR8’s DIMM slots. NOTE: Refer to http://www.asus.com for the list of compatible DIMMs. To install or upgrade the memory modules: 1. Turn off your ROG GR8. 2. Disconnect all cables and peripherals. 3.
5. Slide the side cover towards the rear to detach it from the chassis then gently lift to remove it from the chassis. 6. Pry open the SO-DIMM slot cover.
7. Remove the memory modules. To remove a memory module: A. Press the retaining clips on each side to release the memory module. B. Carefully remove the memory module. C. Repeat steps A and B to remove the other memory module. NOTES: 34 ROG GR8 • Use the same model and speed when replacing memory modules. • Remove the upper memory module first if you wish to replace the lower memory module.
8. Get the replacement memory modules. 9. Install the new memory modules into the slot. IMPORTANT! Always install on the lower slot first when installing one or two modules. To install a new memory module: Align and insert the memory module into the slot (A) then press it down (B) until it is securely seated in place. 10. Replace the SO-DIMM slot cover. Ensure that it is fitted firmly back into its place.
11. Replace the side cover then slide it towards the front of ROG GR8 to re-attach. 12. Press the latch upward to securely fasten the side cover to the chassis.
Installing a 2.5-inch storage drive The ROG GR8 supports one 2.5-inch HDD or one 2.5-inch SSD for additional storage capacity. To install a 2.5-inch HDD or SSD: 1. Turn off your ROG GR8. 2. Disconnect all cables and peripherals. 3. Place the ROG GR8 on its side on a stable and flat surface. 4. Press down the latch at the rear panel to unlock the side cover. NOTE: Before you remove the side cover, ensure that the UNLOCK label on the latch is visible.
5. Slide the side cover towards the rear to detach it from the chassis then gently lift to remove it from the chassis. 6. Remove the four screws that secures the 2.5-inch HDD/SSD extension bay. 7. Using the flap, pull the extension bay to remove it from the chassis.
8. Prepare the 2.5-inch HDD/SSD and the bundled set of four screws. 9. Turn the extension bay upside down and place the 2.5-inch HDD/SSD into the extension bay as shown. Ensure that screw holes on the 2.5-inch HDD/SSD matches the screw holes on the extension bay. 2.5-inch HDD/SSD HDD/SSD screw holes 2.5-inch extension bay extension bay screw holes 10. Secure the 2.5-inch HDD/SSD to the extension bay using the bundled set of screws.
11. Carefully place the 2.5-inch HDD/SSD and extension bay assembly into the drive bay then slide it towards the SATA connector. 2.5-inch HDD/SSD and extension bay assembly HDD/SSD SATA connector Drive bay SATA connector 12. Secure the 2.5-inch extension bay with four screws.
13. Replace the side cover then slide it towards the front of ROG GR8 to re-attach. 14. Move the latch upward to securely fasten the side cover to the chassis.
Appendix
Safety information Your ROG GR8 is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface. Openings on the chassis are for ventilation.
Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users DO NOT throw the ROG GR8 in municipal waste. This product has been designed to enable proper reuse of parts and recycling.
Regulatory notices REACH Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment.
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
France Restricted Wireless Frequency Bands Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are: • • 10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz) 100mW for frequencies between 2446.5 MHz and 2483.5 MHz NOTE: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz.
This requirement is likely to change over time, allowing you to use your wireless LAN card in more areas within France. Please check with ART for the latest information (www.art-telecom.fr) NOTE: Your WLAN Card transmits less than 100mW, but more than 10mW. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
CE Mark Warning CE marking for devices without wireless LAN/Bluetooth The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC “Electromagnetic compatibility” and 2006/95/EC “Low voltage directive”.
ENERGY STAR complied product ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices. All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor and computer are automatically set to sleep after 10 and 30 minutes of user inactivity.
ASUS contact information ASUSTeK COMPUTER INC. Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 Telephone +886-2-2894-3447 Fax +886-2-2890-7798 E-mail info@asus.com.tw Web site www.asus.com.com/ Technical Support Telephone Fax Online support +86-21-38429911 +86-21-5866-8722, ext. 9101# http://www.asus.com/tw/support/ ASUS COMPUTER INTERNATIONAL (America) Address 800 Corporate Way, Fremont, CA 94539, USA Telephone +1-510-739-3777 Fax +1-510-608-4555 Web site http://www.
EC Declaration of Conformity We, the undersigned, Manufacturer: ASUSTeK COMPUTER INC. Address: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN Authorized representative in Europe: ASUS COMPUTER GmbH Address, City: HARKORT STR.
DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Asus Computer International Responsible Party Name: 800 Corporate Way, Fremont, CA 94539. Address: Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Desktop PC Model Number : GR8 Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules.