User’s Manual

SL300C ROG CHARIOT Installation Guide
Package Contents
A
Installing the Lumbar cushion
C
Other features
E
Assembling your chair
B
Put on the gloves before installation.
One by one, insert and push the wheels into the
base.
Insert the hydraulic lift cylinder into the center
hole of the base. Remove the red protective cap
on top if there was any.
Place the telescoping cover on the top of the
hydraulic lift cylinder.
Armrests normally do not
distinguish sides unless labeled
otherwise.
For models with armrest pre-
assembled, please skip this step.
Remove the pre-assembled bolts and washers
(
1
&
3
). Place the 4 large washers (
1
)
between the armrest mounting bar (
2
) and the
seat base. Hold the armrest in place, then insert
and tighten all 4 bolts (
3
). Use the hex key to
tighten them all, and repeat on the other side.
Use the hex key to remove the pre-assembled
bolts and washers from the backrest.
Remove the protective foam covers from the
brackets of the seat base. Then position the
backrest carefully between the brackets. Insert
and attach the 4 bolts (2 on each side) you
removed in step 5 by hand rst. Then use the hex
key to tighten them. Start with the two bolts on
the top of each side, then the bottom two.
E15377 / First Edition / August 2019
Install the side covers and tighten the bolts. (The
covers are marked “L” for the left side and “R” for the
right on the inside.)
Now ip the chair over, facing down. Then remove
the 4 pre-mounted bolts from the underside with
washers.
Repeat the step above to install the control unit,
and then place the nut to mount the hydraulic
lift cylinder facing the back of the seat (where the
backrest is installed).
Insert top of the hydraulic lift cylinder into the
mounting hole on the control unit, and then turn
the chair over in upright position. (Two-person
handling required for your safety)
Hanger at the back of the
chair for hanging your bags,
clothes, cups and more.
Maximum load: 2kg
Please do not hang items
over 2kg.
Lighting up your chair
1. Place your power bank into the
packet at the back of the chair.
2. Connect the USB Type-A
connector to your power bank.
The packet is attached to your
chair with Velcro. You can easily
remove and take it away.
a
Using the RGB controller
1. Aura RGB Lighting: On / Eect / O
Press repeatedly to power the Aura RGB LEDs on or o,
or cycle through the current 7 eects: (1) rainbow (2)
breathing (3) color cycle (4) wave (5) glowing Yo-Yo (6)
strobing (7) static
Press the Aura RGB Lighting button for 3 seconds to
terminate the lighting.
Press it to wake up again or reconnect your powerbank
will keep its previous setting.
NOTE: Your powerbank may automatically adjust its
output when the lighting is terminated. Disconnect
and reconnect it if the Aura RGB Lighting cannot wake
up after toggling it back on.
2. Aura RGB color
Press repeatedly to cycle through the following 8
striking colors: (1) red (2) orange (3) yellow (4) green (5)
blue (6) indigo (7) purple (8) pink
NOTE: This feature is only available on the following
Aura RGB eects: (2) breathing (6) strobing (7) static
3. Aura RGB speed: Slow / Medium / Fast
Press repeatedly to cycle through the following 3 color
eect speeds: (1) Slow (2) Medium (3) Fast
NOTE: This feature is only available on the following
Aura RGB eects: (1) rainbow (2) breathing (3) color
cycle (4) wave (5) glowing Yo-Yo (6) strobing
4. Aura RGB brightness: 50% / 75% / 100%
Three brightness levels. The brightness can be switch
by simple tap to t the environment lighting and
preference.
5. Reset to factory mode
Press the button (2) and button (4) simultaneously to
reset your chair to its factory defaults.
b
1
2
3
4
NOTE: The illustrations are for reference only and may dier from your
actual chair in appearance and features.
1.
Backrest
5.
Wheels
9.
Hydraulic lift cylinder
2.
Seat base
6.
Side covers with bolts
10.
Telescoping cover
3.
Lumbar cushion
7.
Control unit
11.
Hex Key
4.
Wheel base
8.
Gloves
12.
Spare bolt
The chair and the Lumbar cushion are designed
with Velcro fasteners. Attach the Lumbar cushion
to the chair using the Velcro fasteners.
DO NOT remove the non-detachable controller as this
will void the warranty.
D
Rating: 5V 1A