PV100A Series Embedded Computer User Manual
E22768 Revised Edition V2 December 2023 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual..............................................................................................................5 Conventions used in this manual.......................................................................................... 6 Package contents...............................................................................................................7 Chapter 1: Getting to know your Embedded Computer 1.1 Features.......................................................
Appendix Safety information..............................................................................................................38 Setting up your system............................................................................................................. 38 Care during use............................................................................................................................ 39 Regulatory notices...........................................................................
About this manual This manual provides information about the hardware and software features of your Embedded Computer, organized through the following chapters: Chapter 1: Getting to know your Embedded Computer This chapter details the hardware components of your Embedded Computer. Chapter 2: Using your Embedded Computer This chapter provides you with information on using your Embedded Computer.
Conventions used in this manual To highlight key information in this manual, some text are presented as follows: IMPORTANT! This message contains vital information that must be followed to complete a task. NOTE: This message contains additional information and tips that can help complete tasks. WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Embedded Computer's data and components.
Package contents Your Embedded Computer package contains the following items: PV100A Series Adapter cable with switch Cable mount and tie IO port dust covers Additional rubber shock absorbers 7
Optional items High Density cable NOTE: • Some bundled accessories may vary with different models. • The device illustration is for reference only. Actual product specifications may vary with models. • If the device or its components fail or malfunction during normal and proper use within the warranty period, bring the warranty card to the ASUS Service Center for replacement of the defective components.
Getting to know your Embedded Computer 1
1.1 Features 1.1.1 Front view eMMC access LED Power LED Wi-Fi LED LTE LED GPS LED 1.1.2 Reset button Rear view Top: Nano SIM card slot (hot swappable) Bottom: Micro SD card slot USB 3.2 Gen 1 Type-C® OTG port HDMI™ port USB 3.
1.1.3 I/O ports and LEDs GPS LED This LED is used to indicate GPS activity. LED color Status Description Red User defined User defined Green Blink Off Module is transmitting/receiving data Module is not transmitting/receiving data LTE LED This LED is used to indicate LTE activity.
eMMC access LED This indicator lights up when your Embedded Computer is accessing the internal storage drives. LED color Status Description Green Blink eMMC is reading/writing data Power LED This LED lights up depending on the current power status of your Embedded Computer. LED color Status Description Red On Embedded Computer is connected to a power source Green On SOC Power on Reset button The reset button allows you to reset the Embedded Computer.
HDMI™ port The integrated 19-pin HDMI™ (High Definition Multimedia Interface) port with a receptacle connector can support resolutions up to 3840 x 2160 @ 60 Hz on external display devices. LAN port The 8-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network. USB 3.2 Gen 1 port The USB 3.2 Gen 1 (Universal Serial Bus) port provides a transfer rate up to 5 Gbit/s, and provides a maximum of 5V/0.9A output. USB 3.
High Density Cable (HDC) port The HDC port allows you to connect a high density cable that supports various high density interfaces. This port supports 4 x isolated DI, 4 x isolated DO, 2 x RS-232/422/485, 1 x Mic-in, 1 x Line-out, 2 x CANbus (CAN2.0 A/B, CANOpen, J1939, OBDII). NOTE: The HDC port must be used in conjunction with an HDC cable, which is optional and may not come bundled. To purchase an HDC cable, contact your ASUS IOT sales representative.
Serial (COM) connector The 9-pin RS232/422/485 serial (COM) connector allows you to connect devices that have serial ports such as bar code scanner, modem, or printers. Please refer to the table below for the pin definitions of the different COM connectors.
Functional Earth Ground The Functional Earth Ground provides you with a grounding point. GPS Wireless antenna jack The GPS wireless antenna jack allows you to connect a wireless antenna for GPS signals. NOTE: The GPS wireless antenna is optional and may not come bundled. LTE Wireless antenna jack The LTE wireless antenna jack allows you to connect a wireless antenna for LTE signals. NOTE: The LTE wireless antenna is optional and may not come bundled.
Using your Embedded Computer 2
2.1 Getting started 2.1.1 (optional) Connect the AC power adapter If your Embedded Computer package comes bundled with a power adapter, you may follow the steps below to set up your Embedded Computer using the power adapter. NOTE: • This section depends on the availability of the power adapter. The power adapter is optional and may not come bundled. • Recommended wire diameter: 12-24AWG A. Connect the power cord to the AC power adapter. B.
IMPORTANT! • We strongly recommend that you use only the AC power adapter and cable that came with your Embedded Computer. • We strongly recommend that you use a grounded wall socket while using your Embedded Computer. • The socket outlet must be easily accessible and near your Embedded Computer. • To disconnect your Embedded Computer from its main power supply, unplug your Embedded Computer from the power socket.
2.1.2 Connect a display panel to your Embedded Computer You can connect a display panel or projector to your Embedded Computer that has the following connectors: • HDMI connector To connect a display panel to your Embedded Computer: Connect one end of an HDMI cable to an external display, and the other end of the cable to your Embedded Computer’s HDMI port.
2.1.3 Connect the USB cable from keyboard or mouse You can connect generally any USB keyboard and mouse to your Embedded Computer. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your Embedded Computer: Connect the USB cable from your keyboard and mouse to any of the USB ports of your Embedded Computer. NOTE: • The keyboard varies with country or region. • The keyboard and mouse are purchased separately.
2.1.4 Install the cable tie and mount You can install the bundled cable tie and mount which may be used to organize your cables. To install the cable tie and mount to your Embedded Computer: 1. Remove the two (2) rubber plugs from the holes reserved for the cable tie and mount from your Embedded Computer. 2. Insert the cable tie into the cable mount, then install the cable tie and mount to your Embedded Computer. 3. You can organize the cables using the cable mount. 4.
2.2 Installing your Embedded Computer with the wall mount You can install your Embedded Computer to a suitable surface using the wall mounts. Insert four (4) screws into the rubber shock absorbers on the Embedded Computer, then securing the Embedded Computer onto your selected surface using the four (4) screws.
2.3 Configuring the Boot mode You may configure the boot mode of your Embedded Computer using the boot mode switch. The Boot Mode switch allows you to configure between different boot modes and the location to boot from. To configure the boot mode switch: 1. Remove the bottom cover. NOTE: For more information on removing the cover, please refer to the Removing the bottom cover section in this manual. 2.
2.4 Turning your Embedded Computer off If your Embedded Computer is unresponsive, disconnect the power from the Embedded Computer to turn it off.
3 Upgrading your Embedded Computer
IMPORTANT! • Ensure that your hands are dry before proceeding with the rest of the installation process. Before installing any of the features in this guide, use a grounded wrist strap or touch a safely grounded object or metal object to avoid damaging them due to static electricity. • Turn off the power of your Embedded Computer, and allow it to cool for at least 10 minutes before performing any installation/ uninstallation process. NOTE: The illustrations in this section are for reference only.
3.2 Replacing the bottom cover 1. Align the bottom cover with the screw holes and two notch holes, then replace the bottom cover onto the Embedded Computer. 2. Secure the bottom cover using the four (4) screws removed previously.
3.3 Installing an LTE Mini PCIe card Your Embedded Computer comes with a Mini PCIe slot that allow you to install an LTE Mini PCIe card. WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. 1. (optional) If a thermal pad is present on your LTE Mini PCIe card, ensure to remove the plastic film before installing the LTE Mini PCIe card if it is not already removed. 2.
3.4 Installing an M.2 GPS module Your Embedded Computer comes with a M.2 (B-key) slot that allow you to install an M.2 GPS module. WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. 1. (optional) If a thermal pad is present on your M.2 GPS module, ensure to remove the plastic film before installing the M.2 GPS module if it is not already removed. 2. Align and insert the M.
3.5 Installing a Wi-Fi module Your Embedded Computer comes with an M.2 (E-key) slot that allows you to install an M.2 Wi-Fi module. WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. 1. (optional) If a thermal pad is present on your M.2 Wi-Fi module, ensure to remove the plastic film before installing the M.2 Wi-Fi module if it is not already removed. 2. Align and insert the M.
3.6 Installing a nano SIM card Your Embedded Computer comes with two (2) nano SIM card slots, one inside the chassis, and one located in the rear of the Embedded Computer. 3.6.1 Installing a nano SIM card inside the chassis 1. Place the Embedded Computer so that the rear of the Embedded Computer faces away from you. 2. Push the nano SIM cover towards the right of your Embedded Computer. 3. Lift the nano SIM cover. 4. Place the nano SIM into the nano SIM slot. 5. Replace the nano SIM cover. 6.
3.6.2 Installing a nano SIM card to the rear of the Embedded Computer NOTE: This Nano SIM card slot is hot swappable. 1. Remove the two (2) screws securing the Nano SIM card / Micro SD card combo slot cover, then remove the cover. 2. Insert the nano SIM card to the top slot of the Nano SIM card / Micro SD card combo slot. 3. Replace the Nano SIM card / Micro SD card combo slot cover and secure it with the screws removed previously.
3.7 Installing an SD card 1. Remove the two (2) screws securing the Nano SIM card / Micro SD card combo slot cover, then remove the cover. 2. Insert the SD card to the bottom slot of the Nano SIM card / Micro SD card combo slot. 3. Replace the Nano SIM card / Micro SD card combo slot cover and secure it with the screws removed previously.
Appendix
Safety information Your Embedded Computer is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • • • • • 38 Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface.
Care during use • Do not walk on the power cord or allow anything to rest on it. • • Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still flows. Always unplug the power cord from the power outlets before cleaning the system.
DO NOT throw the Embedded Computer in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercurycontaining button cell battery) should not be placed in municipal waste. Check local technical support services for product recycling.
Regulatory notices COATING NOTICE IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located. Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules.
FCC RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
VCCI: Japan Compliance Statement Class A ITE Japan RF Equipment Statement 屋外での使用について 本製品は、5GHz帯域での通信に対応しています。電波法の定めにより 5.2GHz、5.
Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements. Please refer to https://csr.asus.com/Compliance.
Türkiye RoHS AEEE Yönetmeliğine Uygundur ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to https:// csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
UK: The Radio Equipment Regulations 2017 (S.I. 2017/1206) Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
EU: Radio Equipment Directive (Directive 2014/53/EU) Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available athttps://www.asus.
Zjednodušené prohlášení o shodě EU Společnost ASUSTek Computer Inc. tímto prohlašuje, že toto zařízení splňuje základní požadavky a další příslušná ustanovení směrnice 2014/53/ EU. Plné znění prohlášení o shodě EU je k dispozici na adrese https://www.asus.com/support/ V zemích uvedených v tabulce je provoz sítě Wi-Fi ve frekvenčním rozsahu 5 150 - 5 350 MHz povolen pouze ve vnitřních prostorech: Forenklet EU-overensstemmelseserklæring ASUSTeK Computer Inc.
Vienkāršota ES atbilstības paziņojums ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst Direktīvas 2014/53/ES būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem. Pilns ES atbilstības paziņojuma teksts pieejams šeit: https://www.asus.com/support/ Wi-Fi darbība 5150–5350 MHz ir jāierobežo lietošanai telpās valstīs, kuras norādītas tālāk. Supaprastinta ES atitikties deklaracija Šiame dokumente bendrovė „ASUSTek Computer Inc.
Förenklad EU-försäkran om överensstämmelse ASUSTek Computer Inc. deklarerar härmed att denna enhet överensstämmer med de grundläggande kraven och andra relevanta bestämmelser i direktiv 2014/53/EU. Fullständig text av EU-försäkran om överensstämmelse finns på https://www.asus.com/support/ WiFi som använder 5150-5350 MHz kommer att begränsas för användning inomhus i de länder som anges i tabellen: ประกาศเกี่ยวกับความสอดคล้องของสหภาพยุโรปแบบย่อ ASUSTek Computer Inc.
CE RED RF Output table (Directive 2014/53/EU) QUECTEL (Model: EC25-G) Radio Type WCDMA LTE Description Frequency Maximum Output Power (EIRP) 900 880 - 915 MHz 35.0 dBm 1800 1710 - 1785 MHz 32.0 dBm Band 1 1920 - 1980 MHz 25.0 dBm Band 5 824 - 849 MHz 25.0 dBm Band 8 880 - 915 MHz 25.0 dBm B1 1920 - 1980 MHz 25.0 dBm B3 1710 - 1785 MHz 25.0 dBm B5 824 - 849 MHz 25.0 dBm B7 2500 - 2570 MHz 25.0 dBm B8 880 - 915 MHz 25.0 dBm B20 832 - 862 MHz 25.
