E18292 USER GUIDE
E18292 Revised Edition V4 April 2021 Copyright © 2021 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Safety information....................................................................................................... vi Electrical Safety...............................................................................................vi Operation Safety..............................................................................................vi About this guide.........................................................................................................
Contents Chapter 3: Motherboard Information 3.1 Motherboard layout.................................................................................... 3-2 3.2 Onboard buttons and switches................................................................. 3-4 3.3 Jumpers....................................................................................................... 3-5 3.4 Onboard LEDs............................................................................................. 3-7 3.
Contents 4.10 4.11 Exit menu................................................................................................... 4-61 Updating BIOS........................................................................................... 4-62 4.11.1 EZ Update.................................................................................. 4-62 4.11.2 ASUS EZ Flash 3....................................................................... 4-63 4.11.3 ASUS CrashFree BIOS 3................................
Safety information Electrical Safety • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing any additional devices to or from the system, contact a qualified service technician or your dealer.
About this guide Audience This user guide is intended for system integrators, and experienced users with at least basic knowledge of configuring a server. Contents This guide contains the following parts: 1. Chapter 1: Product Introduction This chapter describes the general features of the server, including sections on front panel and rear panel specifications. 2.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
Chapter 1: Product Introduction Product Introduction This chapter describes the general features of the server, including sections on front panel and rear panel specifications.
1.1 System package contents Check your system package for the following items. Model Name Pro E500 G6 Accessories 1 x Pro E500 G6 Support DVD 1 x AC Power Cable 1 x COM port Cable Optional Items Smart Card Reader Anti-Virus CD pack Print port cable DVD-RW Keyboard and mouse If any of the above items is damaged or missing, contact your retailer. 1.
1.3 Pro E500 G6 specifications summary The ASUS Pro E500 G6 is a workstation featuring the ASUS W480/SYS motherboard. 1 x Socket (LGA1200) Processor / System Bus Intel® Xeon® W-1200 Series Processors (up to 125W) Intel® 10th Generation Core™ i9/i7/i5/i3 processors * Refer to www.asus.com for Intel® CPU support list.
Pro E500 G6 specifications summary - Supports HDMI 1.4 with max. resolution 4096 x 2160@24 Hz - Supports DisplayPort 1.2 with max. resolution 4096 x 2304@60 Hz - Supports VGA with max. resolution 1920 x 1200@60 Hz VGA Graphic Audio Auxiliary Storage Device Bay (Floppy / Optical Drive) Up to 1 GPU Card Realtek® ALC887 7.1-Channel High Definition Audio CODEC 2 x 5.25” media bays (No ODD/DVD-RW) 2 x USB 3.2 Gen 1 ports 2 x USB 2.0 ports Front I/O 1 x Headphone port 1 x Microphone port 2 x USB 3.
1.4 Front panel features The Pro E500 G6 workstation features a simple yet stylish front panel design. The power and reset buttons, LED indicators, optical drive, and USB ports are all conveniently located at the front panel for easy access. Optical Drive (Optional) Empty 5.25-inch bay Empty 5.25-inch bay Card reader Smart Card SD/MMC/MS Reset button USB 3.2 Gen 1 ports Power button USB 2.
1.5 Rear panel features The rear panel includes a slot for the motherboard rear I/O ports, expansion slots, a vent for the system fan, and the power supply module. Single power supply Power connector VGA port DisplayPort HDMI Display/Port HDMI port DVI VGA OUT DVI port LAN port 2.5G 120 mm x 120 mm system fan vents USB 3.2 Gen 1 ports USB 3.2 Gen 2 ® Type-C port USB 3.
1.6 Internal features The ASUS Pro E500 G6 Pedestal server system includes the basic components as shown: 1. Power supply unit 2. 120 mm x 120 mm system fan 3. ASUS W480/SYS motherboard 4. Expansion card locks 5. Optical drive (Optional) 6. 1 x 5.25-inch drive bay 7. Front I/O board (hidden) 8. 3 x 3.5-inch Internal storage bays 9. 1 x 2.5-inch Internal storage bay Turn off the system power and detach the power supply before removing or replacing any system component.
1.7 LED information 1.7.
10 USB 3.1 1.7.2 Rear panel LEDs DVI VGA OUT USB 3.0 HDMI ACT/LINK LED DVI Display/Port VGA OUT 2.5G SPEED LED 10 TYPE C SPDIF OUT MIC IN REAR C/SUB LINE OUT LINE IN USB 3.
1-10 Chapter 1: Product Introduction
Chapter 2: Hardware Setup Hardware Setup This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
2.1 Chassis cover 2.1.1 Removing the side cover • Ensure that you unplug the power cord before removing the side cover. • Take extra care when removing the side cover. Keep your fingers from components inside the chassis that can cause injury, such as the CPU fan, rear fan, and other sharp-edged parts. • The images of the system shown in this section are for reference purposes only and may not exactly match the model you purchase. To remove the side cover: 1.
3. Slightly pull the side cover toward the rear just enough to detach it from the chassis. 4. Remove the cover and set it aside.
2.2 CPU installation The motherboard comes with a surface mount LGA1200 socket for Intel® Xeon® W-1200 Series processors and Intel® 10th Generation Core™ i9/i7/i5/i3 processors. Ensure that you install the correct CPU designed for LGA1200 socket only. DO NOT install a CPU designed for other sockets on the LGA1200 socket. 2-4 • Ensure that all power cables are unplugged before installing the CPU.
Load lever Retention tab CPU notches Gold triangle mark Alignment key Alignment key Load plate Load lever Load lever Retention tab Retention lock ASUS Pro E500 G6 2-5
2.3 Cooling system installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan, if necessary.
2.4 System memory The motherboard comes with four DDR 4 (Double Data Rate 4) Dual Inline Memory Modules (DIMM) slots. A DDR4 module is notched differently from a DDR, DDR2 or DDR3 module. DO NOT install a DDR, DDR2 or DDR3 memory module to the DDR4 slot.
Memory configurations You may install 4 GB, 8 GB 16 GB, and 32 GB unbuffered DDR4 DIMMs into the DIMM sockets. You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
2.4.1 Installing a DIMM on a single clip DIMM socket 1. Unlock a DIMM socket by pressing the retaining clip outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the DIMM slot key on the socket. DIMM notch DIMM slot key Unlocked retaining clip A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket in the wrong direction to avoid damaging the DIMM. 3.
2.5 Front panel cover Before you can install a 5.25-inch drive, you should first remove the front panel cover. Ensure to unplug the power cable before installing or removing any system components. Failure to do so may cause damage to the motherboard and other system components! 2.5.1 Removing the front panel cover To remove the front panel cover: 1. Locate the front panel assembly lock then slide it outward to unlock the latches that secure the front panel cover to the chassis. Assembly lock 2.
2.6 5.25-inch drives This system comes with three 5.25-inch drive bays located on the upper front section of the chassis. If your system came with an optical drive, the optical drive occupies the topmost bay (1). The lower bays (2 and 3) are available for additional 5.25-inch optical, zip, or floppy disk drives. Installing a 5.25-inch drive To install a 5.25-inch drive: 1. Remove the front panel cover. Refer to the Removing the front panel cover section for more information. 2.
4. Prepare the 5.25-inch drive. 5. Insert and carefully push the drive into the bay until its screw holes align with the holes on the bay. 6. Push the bay locks to secure the drive in place. Bay locks 7. Connect the SATA cable to the SATA connector of the drive. 8. Connect a SATA power cable from the power supply to the power connector of the drive. 9. Reinstall the front panel cover.
2.7 Hard disk drives (HDD) The server system supports three (3) 3.5-inch Serial ATA hard disk drives via the hard disk drive bays and one 2.5-inch HDD/SSD drive at the bottom of the HDD cage. Installing 3.5-inch HDDs To install 3.5-inch Serial ATA hard disk drives: 1. Remove the side cover of the chassis. Refer to the Removing the side cover section for more information. 2. Prepare the 3.5-inch HDD and the bundled set of screws. 3.
2-14 5. Secure the 3.5-inch HDD to the HDD cage using the bundled set of screws. 6. Swing the HDD cage inwards until it clicks back into place. 7. Connect the SATA cable and SATA power cable to the 3.5-inch HDD.
Installing 2.5-inch HDD/SSD To install a 2.5-inch HDD/SSD: 1. Remove the side cover of the chassis. Refer to the Removing the side cover section for more information. 2. Prepare the 2.5-inch HDD/SDD and the bundled set of screws. 3. Lay the system on its side on a flat and stable surface. 4. Locate the HDD cage lock, press it up (A), then swing the HDD cage outwards (B). 5. Align and insert the 2.5-inch HDD/SSD into the drive bay as shown.
2-16 6. Secure the 2.5-inch HDD/SSD to the HDD cage using the bundled set of screws. 7. Swing the HDD cage inwards until it clicks back into place. 8. Connect a SATA cable and a SATA power cable to the 2.5-inch HDD/SSD.
2.8 Expansion slots Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Slot No.
2.8.1 Installing an expansion card To install an expansion card: 1. Lay the system on its side on a flat, stable surface. 2. Press the PCIe latch (A), hold it by its edge then lift it towards the rear (B). Edge of the PCIe latch PCIe latch 3. Remove the screw (A) that secures the metal bracket to the chassis then remove the metal bracket (B).
4. Align and insert the expansion card into the PCIe slot. 5. Lift the PCIe latch inwards until it clicks into place securing the expansion card to the chassis. Expansion card PCIe slot PCIe latch 6. (Optional) Replace the screw of the metal bracket.
2.8.2 Configuring an expansion card VGA configuration 2-20 PCI Express operating mode PCIe 3.0 x16_1 (gray) PCIe 3.0 x16_2 PCIe 3.0 x16_3 Single VGA/PCIe card x16 (Recommended for single VGA card) N/A N/A Dual VGA/PCIe cards x8 x8 N/A Triple VGA/PCIe cards x8 x8 x4 • In single VGA card mode, use the PCIe 3.0 x16_1 slot (gray) for a PCI Express x16 graphics card to get better performance. • We recommend that you provide sufficient power when running CrossFireX™ mode.
2.8.3 Installing M.2 (NGFF) cards To install an M.2 card: 1. Locate the M.2 connector (M.2(SOCKET3)) on the motherboard. NGFF1 2. Remove the screw on the stand screw. Screw Screw hole Stand screw 3. Prepare the M.2 card. 4. Align and insert the M.2 card into the M.2 connector (M.2(SOCKET3)). 5. Secure the M.2 card with the screw you removed in step 2. • Please pay attention when removing the screw, the stand screw might be removed together with it. • Ensure that the M.
2.9 System fan This section describes how to remove the system fan in the event that you need to install or remove previously installed or new system components, or when the system fan needs to be replaced because it was damaged or became defective. To remove the system fan: 1. Disconnect the system fan cable from the CHA_FAN1 connector on the motherboard. 2. Remove the four system fan screws at the rear panel. Keep the screws for later use.
2.10 BIOS update utility USB BIOS FlashBack™ USB BIOS FlashBack™ allows you to easily update the BIOS without entering a bootable environment, ideal for BIOS recovery, rollback, or updates to support new CPUs. Simply insert a USB storage device to the USB port (the USB port is marked the I/O shield) then press the USB BIOS FlashBack™ button for three seconds to start the update process. To use USB BIOS FlashBack™: 1. Download the latest BIOS from the support site at www.asus.
Refer to section Onboard LEDs for more information of the FlashBack™ LED. 5. Wait until the light goes out, indicating that the BIOS updating process is completed. For more BIOS update utilities in BIOS setup, refer to the section Updating BIOS in Chapter 4. • Do not unplug portable disk, power system, or short the CLRTC header while BIOS update is ongoing, otherwise update will be interrupted.
2.11 Motherboard rear and audio connection 2.11.1 Rear I/O connection Rear panel connectors 1. DisplayPort 7. DVI-D port 2. VGA port 8. USB 3.2 Gen 1 ports 5 and 6 3. Intel® LAN I225 9. USB 3.2 Gen 1 ports 3 and 4 4. Intel® LAN I219 10. USB 3.2 Gen 2 Type-C® port EC1 5. USB 3.2 Gen 2 Type-A port E1 11. Optical S/PDIF Out port 6. HDMI 1.4b port 12. Audio I/O ports* * : Refer to the tables below for audio port definitions. * Audio 2, 4, 5.1 or 7.
2.11.
Connect to 4-channel Speakers Connect to 5.1-channel Speakers Connect to 7.
2-28 Chapter 2: Hardware Setup
Chapter 3: Motherboard Information Motherboard Information This chapter includes the motherboard layout and brief descriptions of the jumpers and internal connectors.
3.
Layout contents Connectors/Jumpers/Buttons and switches/Slots Page 1. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V; 6-pin EATX12V_1) 3-15 2. LGA1200 CPU socket 2-4 3. Fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-3) 3-13 4. DDR4 DIMM slots 2-7 5. USB 3.2 Gen 1 connector (20-1 pin U32G1_12) 3-11 6. M.2 sockets (M.2_1; M.2_2) 3-16 7. Intel® Serial ATA 6 Gb/s connectors (7-pin SATA6G_1-8) 3-9 8. Q-Code LED 3-8 9. BIOS FlashBack™ button 2-23 10.
3.2 Onboard buttons and switches Onboard buttons and switches allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1. Power-on button The motherboard comes with a power-on button that allows you to power up or wake up the system.
3.3 1. Jumpers Clear RTC RAM (2-pin CLRTC) This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Use a metal object such as a screwdriver to short the two pins. 3.
2. LPT and Q-Code switch (3-pin LPT_P80_SW) This header allows you to enable either LPT (Line Printing Thermal) connector or Q-Code at a time. To switch between LPT and Q-Code: 3-6 1. Turn OFF the computer and unplug the power cord. 2. Move the jumper cap to switch between LPT and Q-Code. 3. Plug the power cord and turn ON the computer.
3.4 1. Onboard LEDs Q LED (CPU, DRAM, VGA, BOOT) Q LED checks key components (CPU, DRAM, VGA card, and booting devices) in sequence during motherboard booting process. If an error is found, the corresponding LED remains lit until the problem is solved. This user-friendly design provides an intuitive way to locate the root problem within seconds. The Q LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case. 2.
3. Q-Code LED The Q-Code LED design provides you with a 2-digit error code that displays the system status. Refer to the Q-Code table on the next page for details. The Q-Code LED provides the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case.
3.5 Internal connectors 1. Intel Serial ATA 6 Gb/s connectors (7-pin SATA6G_1-8) ® These connectors connect to Serial ATA 6 Gb/s hard disk drives via Serial ATA 6 Gb/s signal cables. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology enterprise through the onboard Intel® W480 chipset. • These connectors are set to [AHCI Mode] by default.
2. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this connector. We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability. 3.
4. USB 3.2 Gen 1 connector (20-1 pin U32G1_12) This connector allows you to connect a USB 3.2 Gen 1 module for additional USB 3.2 Gen 1 front or rear panel ports. With an installed USB 3.2 Gen 1 module, you can enjoy all the benefits of USB 3.2 Gen 1 including faster data transfer speeds of up to 5 Gb/s, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. The USB 3.2 Gen 1 module is purchased separately. The plugged USB 3.
5. USB 2.0 connectors (10-1 pin USB1112, USB1314; 4-pin Type-A USB9) The 10-1 pin connector allows you to connect a USB 2.0 module for additional USB 2.0 front or rear panel ports. The 4-pin USB (Universal Serial Bus) Type-A port is available for connecting USB 2.0 devices. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. DO NOT connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! 6.
7. Fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-3) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. 8. • DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
9. System panel connector (20-3 pin PANEL) This connector supports several chassis-mounted functions. • System power LED (2-pin or 3-1 pin PLED) The 2-pin or 3-1 pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. • Hard disk drive activity LED (2-pin HDD_LED) This 2-pin connector is for the HDD Activity LED.
10. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V; 6-pin EATX12V_1) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. Ensure to connect the 8-pin power plug, or connect both the 8-pin and 6-pin power plugs.
11. M.2 sockets (M.2_1; M.2_2) These sockets allow you to install M.2 SSD modules. • M.2_1 socket supports PCIe 3.0 x4 and SATA mode M Key design and type 2242 / 2260 / 2280 PCIe and SATA storage devices. • M.2_2 socket supports PCIe 3.0 x4 M Key design and type 2242 / 2260 / 2280 / 22110 PCIe storage devices. • M.2_1 socket shares bandwidth with SATA6G_2 port. When M.2_1 slot runs in SATA mode, the SATA6G_2 port will be disabled. • These sockets support IRST (Intel® Rapid Storage Technology).
12. LPT connector (26-1 pin LPT) The LPT (Line Printing Terminal) connector supports devices such as a printer. LPT standardizes as IEEE 1284, which is the parallel port interface on IBM PC-compatible computers. 13. Thermal Sensor connector (2-pin T_SENSOR) The Thermal Sensor connector allows you to connect a sensor to monitor the temperature of the devices and the critical components inside the motherboard.
3-18 Chapter 3: Motherboard Information
Chapter 4: BIOS Setup BIOS Setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
4.1 Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
4.2 BIOS setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup, press or during the Power-On Self Test (POST). If you do not press or , POST continues with its routines. Entering BIOS Setup after POST To enter BIOS Setup after POST: • Press ++ simultaneously.
4.2.1 EZ Mode The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance, mode and boot device priority. To access the Advanced Mode, select Advanced Mode or press the hotkey for the advanced BIOS settings. The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section Boot menu for details.
4.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To switch from EZ Mode to Advanced Mode, click Advanced Mode(F7) or press the hotkey.
Menu bar The menu bar on top of the screen has the following main items: My Favorites For saving the frequently-used system settings and configuration. Main For changing the basic system configuration Ai Tweaker For changing the overclocking settings Advanced For changing the advanced system settings Monitor For displaying the system temperature, power status, and changing the fan settings.
Search (F9) This button allows you to search for BIOS items by entering its name, enter the item name to find the related item listing. Hot keys This button contains the navigation keys for the BIOS setup program. Use the navigation keys to select items in the menu and change the settings. Scroll bar A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen.
4.2.3 Q-Fan Control The QFan Control allows you to set a fan profile or manually configure the operating speed of your CPU and chassis fans.
Configuring fans manually Select Manual from the list of profiles to manually configure your fans’ operating speed. Speed points Select to manually configure your fans To configure your fans: 1. Select the fan that you want to configure and to view its current status. 2. Click and drag the speed points to adjust the fans’ operating speed. 3. Click Apply to save the changes then click Exit (ESC).
4.3 My Favorites My Favorites is your personal space where you can easily save and access your favorite BIOS items. My Favorites comes with several performance, power saving, and fast boot related items by default. You can personalize this screen by adding or removing items.
Adding items to My Favorites To add BIOS items: from the BIOS screen to open 1. Press on your keyboard or click Setup Tree Map screen. 2. On the Setup Tree Map screen, select the BIOS items that you want to save in My Favorites screen. Main menu panel Selected shortcut items Submenu panel Delete all favorite items Recover to default favorite items 3. Select an item from main menu panel, then click the submenu that you want to save as or press on your keyboard.
4.4 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security The Security menu items allow you to change the system security settings. 4-12 • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password.
Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the Administrator Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Re-type to confirm the password then select OK. To change an administrator password: 1.
4.5 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking-related items. Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction. The configuration options for this section vary depending on the motherboard model, as well as the CPU and DIMM model you installed on the motherboard. Scroll down to display other BIOS items.
The following item appears only when Ai Overclock Tuner is set to [XMP I] or [XMP II]. XMP This item allows you to select your eXtreme Memory Profile (XMP). Each profile has its own DRAM frequency, timing and voltage. The following items appear only when Ai Overclock Tuner is set to [XMP I], [XMP II], or [Manual]. BCLK Frequency This item allows you to set the BCLK (base clock) frequency to enhance the system performance. Use the <+> or <-> to adjust the value.
CPU Core Ratio This item allows you to set the CPU core ratios. Configuration options: [Auto] [Sync All Cores] [By Core Usage] [AI Optimized] The [AI Optimized] item appears only when you use an unlocked CPU. The following item appears only when CPU Core Ratio is set to [Sync All Cores]. ALL-Core Ratio Limit Enter [Auto] to apply the CPU default Turbo Ratio setting or manually assign a Core ratio limit to synchronize all cores. The following item appears only when CPU Core Ratio is set to [By Core Usage].
Primary Timings DRAM CAS# Latency Configuration options: [Auto] [1] - [31] DRAM RAS# to CAS# Delay Configuration options: [Auto] [1] - [63] DRAM RAS# ACT Time Configuration options: [Auto] [1] - [63] DRAM Command Rate Configuration options: [Auto] [1N] [2N] [3N] [N:1] The following item appears only when DRAM Command Rate is set to [N:1]. N to 1 ratio Number of bubbles between wach valid command cycle.
DRAM WRITE to READ Delay S Configuration options: [Auto] [1] - [15] DRAM CKE Minimum Pulse Width Configuration options: [Auto] [0] - [15] DRAM Write Latency Configuration options: [Auto] [1] - [31] Skew Control ODT RTT WR (CHA) Configuration options: [Auto] [0 DRAM CLOCK] [80 DRAM CLOCK] [120 DRAM CLOCK] [240 DRAM CLOCK] [255 DRAM CLOCK] ODT RTT PARK (CHA) Configuration options: [Auto] [0 DRAM CLOCK] [34 DRAM CLOCK] [40 DRAM CLOCK] [48 DRAM CLOCK] [60 DRAM CLOCK] [80 DRAM CLOCK] [120 DRAM CLOCK] [240 DRAM
Cmd Rising Slope Configuration options: [Auto] [0] - [15] Cmd Rising Slope Offset Configuration options: [Auto] [0] - [1] Ctl Rising Slope Configuration options: [Auto] [0] - [15] Ctl Rising Slope Offset Configuration options: [Auto] [0] - [1] Clk Rising Slope Configuration options: [Auto] [0] - [15] Clk Rising Slope Offset Configuration options: [Auto] [0] - [1] Data Falling Slope Configuration options: [Auto] [0] - [15] Data Falling Slope Offset Configuration options: [Auto] [0] - [1] Cmd Falling Slope Co
DRAM RTL (CHB DIMM0 Rank0) Configuration options: [Auto] [0] - [127] DRAM RTL (CHB DIMM0 Rank1) Configuration options: [Auto] [0] - [127] DRAM RTL (CHB DIMM1 Rank0) Configuration options: [Auto] [0] - [127] DRAM RTL (CHB DIMM1 Rank1) Configuration options: [Auto] [0] - [127] DRAM IOL (CHA DIMM0 Rank0) Configuration options: [Auto] [0] - [15] DRAM IOL (CHA DIMM0 Rank1) Configuration options: [Auto] [0] - [15] DRAM IOL (CHA DIMM1 Rank0) Configuration options: [Auto] [0] - [15] DRAM IOL (CHA DIMM1 Rank1) Confi
Early Command Training Configuration options: [Enabled] [Disabled] SenseAmp Offset Training Configuration options: [Enabled] [Disabled] Early ReadMPR Timing Centering 2D Configuration options: [Enabled] [Disabled] Read MPR Training Configuration options: [Enabled] [Disabled] Receive Enable Training Configuration options: [Enabled] [Disabled] Jedec Write Leveling Configuration options: [Enabled] [Disabled] LPDDR4 Write DQ DQS Retraining Configuration options: [Enabled] [Disabled] Early Write Time Centering 2
Read Timing Centering 2D Configuration options: [Enabled] [Disabled] Command Voltage Centering Configuration options: [Enabled] [Disabled] Write Voltage Centering 2D Configuration options: [Enabled] [Disabled] Read Voltage Centering 2D Configuration options: [Auto] [Enabled] [Disabled] Late Command Training Configuration options: [Auto] [Enabled] [Disabled] Round Trip Latency Configuration options: [Auto] [Enabled] [Disabled] Turn Around Timing Training Configuration options: [Enabled] [Disabled] Rank Margi
Third Timings tRDRD_sg_Training Configuration options: [Auto] [0] - [63] tRDRD_sg_Runtime Configuration options: [Auto] [0] - [63] tRDRD_dg Configuration options: [Auto] [0] - [63] tRDWR_sg Configuration options: [Auto] [0] - [63] tRDWR_dg Configuration options: [Auto] [0] - [63] tWRWR_sg Configuration options: [Auto] [0] - [63] tWRWR_dg Configuration options: [Auto] [0] - [63] tWRRD_sg Configuration options: [Auto] [0] - [127] tWRRD_dg Configuration options: [Auto] [0] - [63] tRDRD_dr Configuration options
TWRPRE Configuration options: [Auto] [0] - [127] TRDPRE Configuration options: [Auto] [0] - [15] tREFIX9 Configuration options: [Auto] [0] - [127] OREF_RI Configuration options: [Auto] [0] - [255] Misc. MRC Fast Boot Allows you to enable, disable or automatically set the MRC fast boot. Configuration options: [Auto] [Enabled] [Disabled] Delay after Train This item allows you to enable 10 second delay after training for DRAM to reach a certain temperature during extreme overclocking.
DLLBwEn Select values 2 to 4 for best memory overclocking. Configuration options: [Auto] [0] - [7] Legacy Mode This item allows you to enable or disable to work around issues in Legacy Mode. Configuration options: [Enabled] [Disabled] SPD Write Disable This item allows you to enable or disable setting the SPD Write Disable. For security recommendations, SPD write disable must be set.
The following item appears only when CPU VRM Switching Frequency is set to [Manual]. Fixed CPU VRM Switching Frequency (KHz) This item allows you to set a higher frequency for a quicker transient response speed. Use the <+> or <-> to adjust the value. The values range from 250 to 500 with an interval of 50. The following item appears only when CPU VRM Switching Frequency is set to [Auto]. VRM Spread Spectrum This item allows you to reduce the magnitude of peak noise from the VRM.
Boosted performance may vary depending on the CPU Graphics specification. DO NOT remove the thermal module. CPU Graphics Current Capability The CPU Graphics current capability adjusts the total power range for CPU Graphics overclocking. A higher value provides a wider total power range and extends the overclocking frequency range simultaneously. Configuration options: [Auto] [100%] - [140%] Configure higher values when overclocking or under a high CPU Graphics loading for extra support.
Internal CPU Power Management The items in this submenu allow you to set the CPU ratio and features. Maximum CPU Core Temperature This item allows you to set the allowable temperature for CPU cores. The CPU will throttle or shutdown when it reaches this temperature to prevent damaging the cores. Use the <+> and <-> keys to adjust the value. Configuration options: [Auto] [62] - [115] Turbo Mode Parameters CPU Core/Cache Current Limit Max.
TVB Voltage Optimizations This item controls thermal based voltage optimizations for processors that implement the Intel Thermal Velocity Boost (TVB) feature. Configuration options: [Auto] [Enabled] [Disabled] TVB Ratio Clipping This service controls Core frequency reduction caused by high package temperatures for processors that implement the Intel Thermal Velocity Boost (TVB) feature. It is required to be disabled for supporting overclocking at frequencies higher than the default max turbo frequency.
CPU Core/Cache Voltage Configures the mode of Voltage fed to the cores of the processor. Configuration options: [Auto] [Manual Mode] [Offset Mode] [Adaptive Mode] The following item appears only when CPU Core/Cache Voltage is set to [Manual Mode]. CPU Core Voltage Override Allows you to configure the CPU Core voltage. Configuration options: [Auto] [0.600] - [1.700] The following items appear only when CPU Core/Cache Voltage is set to [Offset Mode].
PLL Termination Voltage Configuration options: [Auto] [0.800] - [1.600] CPU Graphics Voltage Mode This item allows you to configure the mode of voltage fed to the CPU Graphics. Manual mode allows user-defined values. Offset mode modifies values by SVID. Configuration options: [Auto] [Manual Mode] [Offset Mode] The following item appears only when CPU Graphics Voltage Mode is set to [Manual Mode]. CPU Graphics Voltage Override Allows you to configure the CPU Core voltage. Configuration options: [Auto] [0.
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL0-7 Configures the DRAM Data REF Voltage. Configuration options: [Auto] [0] - [63] DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL0-7 Configures the DRAM Data REF Voltage. Configuration options: [Auto] [0] - [63] 4.6 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.
4.6.1 Platform Misc Configuration The items in this menu allow you to configure the platform-related features. PCI Express Native Power Management This item allows you to enhance the power saving feature of PCI Express and perform ASPM operations in the operating system. Configuration options: [Disabled] [Enabled] The following item appears only when PCI Express Native Power Management is set to [Enabled].
SA - PCI Express DMI Link ASPM Control This item allows you to enable or disable control of the Active State Power Management on SA side of the DMI Link. Configuration options: [Disabled] [L0s] [L1] [L0sL1] PEG - ASPM This item allows you to control the ASPM support for the PEG 0. This has no effect if PEG is not the currently active device. Configuration options: [Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1] 4.6.
Hardware Prefetcher This item allows you to enable or disable the MLC streamer prefetcher. Configuration options: [Disabled] [Enabled] Adjacent Cache Line Prefetch This item allows you to prefetch adjacent cache lines, reducing the DRAM loading time and improving the system performance. Configuration options: [Disabled] [Enabled] Intel (VMX) Virtualization Technology When set to [Enabled], VMX can utilize the additional hardware capabilities provided by Vanderpool Technology.
Intel(R) Speed Shift Technology This item allows you to disable or enable Intel(R) Speed Shift Technology support. When enabled, CPPC v2 interface allows hardware controlled P-states. Configuration options: [Auto] [Enabled] [Disabled] Intel(R) Turbo Boost Max Technology 3.0 This item allows you to disable or enable Intel(R) Turbo Boost Max Technology 3.0 support. When disabled, it will report the maximum ratio from CPPC v2 MSR 0x771.
CPU C7 Report This item allows you to disable or enable the CPU C7 report to the operating system. Configuration options: [CPU C7] [CPU C7s] [Disabled] CPU C8 Report This item allows you to disable or enable the CPU C8 report to the operating system. Configuration options: [Enabled] [Disabled] CPU C9 Report This item allows you to disable or enable the CPU C9 report to the operating system.
4.6.3 System Agent (SA) Configuration VT-d Allows you to enable virtualization technology function on memory control hub. Configuration options: [Enabled] [Disabled] Above 4G Decoding This item enables or disables 64-bit capable devices to be decoded in above 4G address space if your system supports 64-bit PCI Decoding. Configuration options: [Enabled] [Disabled] Memory Configuration This item allows you to set memory configuration parameters.
DVMT Pre-Allocated This item allows you to select the DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. Configuration options: [32M] - [1024M] RC6(Render Standby) This item allows you to enable render standby support. Configuration options: [Disabled] [Enabled] PEG Port Configuration This item allows you to configure the PEG Port settings. The items in this submenu may vary according to your motherboard.
4.6.5 PCH Storage Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Empty if no SATA device is installed to the corresponding SATA port. Scroll down to display the other BIOS items. SATA Controller(s) This item allows you to enable or disable the SATA Device. Configuration options: [Disabled] [Enabled] The following items appear only when SATA Controller(s) is set to [Enabled].
SMART Self Test S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system that shows a warning message during POST (Power-on Self Test) when an error occurs in the hard disks. Configuration options: [On] [Off] SATA6G_1(Gray) - SATA6G_6(Gray) The items in this submenu may vary according to your motherboard. SATA6G_1(Gray) - SATA6G_6(Gray) This item allows you to enable or disable the selected SATA port.
4.6.7 PCI Subsystem Settings SR-IOV Support This option enables or disables Single Root IO Virtualization Support if the system has SRIOV capable PCIe devices. Configuration options: [Disabled] [Enabled] 4.6.8 USB Configuration The items in this menu allow you to change the USB-related features. The items in this menu may vary according to your motherboard. The Mass Storage Devices item shows the auto-detected values. If no USB device is detected, the item shows None.
Legacy USB Support [Enabled] Your system supports the USB devices in legacy operating systems. [Disabled] Your USB devices can be used for BIOS setup only and cannot be recognized in the boot devices list. [Auto] Your system automatically detects the presence of USB devices at startup. If any USB devices are detected, the legacy USB support is enabled. XHCI Hand-off This item is set to [Disabled] by default for the EHCI (enhanced host controller interface) support by XHCI drivers in operating systems.
4.6.10 NVMe Configuration This menu displays the NVMe controller and Drive information of the connected devices. 4.6.11 Onboard Devices Configuration The items in this menu may vary according to your motherboard. Scroll down to view the other BIOS items. Hyper M.2X16 This item allows you to set different configurations for the Hyper M.2X16 card. The configurations may differ between motherboards. Please refer to your motherboard’s user manual for more information on the configurations.
Intel I219-LM LAN Controller This item allows you to enable or disable the onboard NIC. Configuration options: [Disabled] [Enabled] Intel I225-LM LAN Controller This item allows you to enable or disable the Intel LAN. Configuration options: [Disabled] [Enabled] Asmedia USB 3.2 Controller (Back 1A 1C) Configuration options: [Disabled] [Enabled] USB power delivery in Soft Off State (S5) This item allows you to enable or disable USB power when your PC is in the S5 state.
4.6.12 APM Configuration Restore AC Power Loss This item allows your system to go to ON state, OFF state, or both states after an AC power loss. When setting your system to [Last State], it goes to the previous state before the AC power loss. Configuration options: [Power Off] [Power On] [Last State] Energy Star Ready Configuration options: [Disabled] [Enabled] ErP Ready This item allows you to switch off some power at S4+S5 or S5 to get the system ready for ErP requirement.
4.6.13 HDD/SSD SMART Information This menu displays the SMART information of the connected devices. NVM Express devices do not support SMART information.
4.7 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. The items in this menu may vary according to your motherboard. Scroll down to display the other BIOS items. CPU Temperature, CPU Package Temperature, Motherboard Temperature, Chipset Temperature, T_Sensor Temperature [xxx°C/xxx°F] The onboard hardware monitor automatically detects and displays the CPU, CPU Package, and motherboard temperatures.
Q-Fan Configuration AI Cooling ASUS AI Cooling will automatically manage and control all motherboard fans, ensuring the most efficient settings are set depending on the current system load and temperature. When you enable this function, AI Cooling function will try to lower fan speed to decrease fan noise without compromising current performance. You can keep track of fan performance via the ASUS Fan Xpert software with a blue dot in the Fan curve chart.
The following items appear only when CPU Fan Profile is set to [Manual]. CPU Upper Temperature Use the <+> or <-> keys to adjust the upper limit of the CPU temperature. The CPU fan will operate at the maximum duty cycle when the temperature source is higher than the limit. CPU Max. Duty Cycle (%) Use the <+> or <-> keys to adjust the maximum CPU fan duty cycle. When the temperature source reaches the upper limit, the CPU fan will operate at the maximum duty cycle.
Chassis Fan 1-3 Step Up This item allows you to set the value of the chassis fan step up. Configuration options: [0 sec] [12 sec] [25 sec] [51 sec] [76 sec] [102 sec] [127 sec] [153 sec] [178 sec] [204 sec] Chassis Fan 1-3 Step Down This item allows you to set the value of the chassis fan step down.
Chassis Intrusion Detection Support Set this item to [Enabled] to enable the chassis intrusion detection function. Configuration options: [Enabled] [Disabled] CPU Temperature LED Switch This item allows you to turn the CPU Temperature LED on or off.
4.8 Boot menu The Boot menu items allow you to change the system boot options. CSM (Compatibility Support Module) This item allows you to configure the CSM (Compatibility Support Module) items to fully support the various VGA, bootable devices and add-on devices for better compatibility. Launch CSM [Enabled] For better compatibility, enable the CSM to fully support the non-UEFI driver add-on devices or the Windows® UEFI mode.
Secure Boot This item allows you to configure the Windows® Secure Boot settings and manage its keys to protect the system from unauthorized access and malwares during POST. OS Type [Windows UEFI Mode] [Other OS] This item allows you to select your installed operating system. Execute the Microsoft® Secure Boot check. Only select this option when booting on Windows® UEFI mode or other Microsoft® Secure Boot compliant OS. Get the optimized function when booting on Windows® nonUEFI mode.
KEK Management The KEK (Key-exchange Key or Key Enrollment Key) manages the Signature database (db) and Revoked Signature database (dbx). Key-exchange Key (KEK) refers to Microsoft® Secure Boot Key-Enrollment Key (KEK). Save to file This item allows you to save the KEK to a USB storage device. Set New key This item allows you to load the downloaded KEK from a USB storage device. Append Key This item allows you to load the additional KEK from a storage device for an additional db and dbx loaded management.
Set New Key This item allows you to load the downloaded dbx from a USB storage device. Append Key This item allows you to load the additional dbx from a storage device for an additional db and dbx loaded management. Delete Key This item allows you to delete the dbx file from your system. Configuration options: [Yes] [No] The dbx file must be formatted as a UEFI variable structure with time-based authenticated variable.
4.9 Tool menu The Tool menu items allow you to configure options for special functions. Select an item then press to display the submenu. Flexkey [Reset] Reboots the system. [DirectKey] Boot directly into the BIOS. Setup Animator This item allows you to enable or disable the Setup animator. Configuration options: [Disabled] [Enabled] 4.9.1 ASUS EZ Flash 3 Utility This item allows you to run ASUS EZ Flash 3. When you press , a confirmation message appears.
4.9.2 Secure Erase SSD speeds may lower over time as with any storage medium due to data processing. Secure Erase completely and safely cleans your SSD, restoring it to factory performance levels. To launch Secure Erase, click Tool > Secure Erase on the Advanced mode menu. • The time to erase the contents of your SSD may take a while depending on its size. Do not turn off the system during the process. • Secure Erase is only supported on Intel SATA port.
4.9.3 ASUS User Profile This item allows you to store or load multiple BIOS settings. Load from Profile This item allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your BIOS settings, press , and then select Yes. • DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure! • We recommend that you update the BIOS file only coming from the same memory/ CPU configuration and BIOS version.
4.9.4 ASUS SPD Information This item allows you to view the DRAM SPD information.
4.10 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select OK to load the default values.
4.11 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility,and performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result to system’s failure to boot. Carefully follow the instructions in this chapter to update your BIOS when necessary. Visit http://www.asus.
4.11.2 ASUS EZ Flash 3 ASUS EZ Flash 3 allows you to download and update to the latest BIOS using a USB drive. To update the BIOS: 1. Insert the USB flash drive that contains the latest BIOS file to the USB port. 2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash Utility and press . 3. Press to switch to the Drive field. 4. Press the Up/Down arrow keys to find the USB flash drive that contains the latest BIOS, and then press . 5.
4.11.3 ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the BIOS file. The BIOS file in the motherboard support DVD may be older than the BIOS file published on the ASUS official website. If you want to use the newer BIOS file, download the file at https://www.asus.
Chapter 5: RAID Configuration RAID Configuration This chapter provides instructions for setting up, creating, and configuring RAID sets using the available utilities.
5.1 RAID configurations The motherboard supports Intel® Rapid Storage Technology enterprise Option ROM Utility with RAID 0, RAID 1, RAID 10, and RAID 5 support. If you want to install a Windows® operating system to a hard disk drive included in a RAID set, you have to create a RAID driver disk and load the RAID driver during OS installation. Refer to section Creating a RAID driver disk for details. 5.1.
5.1.2 Installing storage devices The motherboard supports Serial ATA hard disk drives and PCIE SSD storage devices. For optimal performance, install identical drives of the same model and capacity when creating a disk array. Refer to Chapter 2 for details on installing storage devices to your motherboard. 5.1.3 Intel® Rapid Storage Technology in UEFI BIOS To enter the Intel® Rapid Storage Technology in UEFI BIOS: 1. Enter the BIOS Setup during POST. 2.
Creating a RAID set To create a RAID set: 5-4 1. From the Intel® Rapid Storage Technology menu, select Create RAID Volume and press . The following screen appears: 2. When the Name item is selected, enter a name for the RAID set and press . 3. When the RAID Level item is selected, press to select the RAID level to create, and then press . 4. Under Select Disks, press and select X for the disks you want to include in the RAID set.
5. When the Strip Size item is selected, press to select strip size for the RAID array (for RAID 0, 10 and 5 only), and then press . The available strip size values range from 4 KB to 128 KB. The following are typical values: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB We recommend a lower strip size for server systems, and a higher strip size for multimedia computer systems used mainly for audio and video editing. 6.
Deleting a RAID set Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 5-6 1. From the Intel® Rapid Storage Technology menu, select the RAID volume you want to delete and press . The following screen appears: 2. When the Delete item is selected, press , then select Yes to delete the RAID volume and return to the Intel® Rapid Storage Technology menu, or select No to cancel.
5.1.4 Intel® Rapid Storage Technology Option ROM utility To enter the Intel® Rapid Storage Technology Option ROM utility: 1. Enter the BIOS Setup during POST. 2. Go to the Boot menu > CSM (Compatibility Support Module) > Launch CSM, then set the item to [Enabled]. 3. Save your changes and exit the BIOS Setup, then during POST, press + to display the utility main menu. RAID Volumes: None defined.
Creating a RAID set To create a RAID set: 1. From the utility main menu, select 1. Create RAID Volume and press . The following screen appears: Name: Volume 0 RAID Level: aaaaaaaaaaaaaaa Disks: dssdsdsds Strip Size:aaaaaaaaaaaaaaaa Capacity:aaaaaaaaaaaaaa Sync:aaaaaaaaaa Create volume [HELP] Enter a unique volume name that has no special characters and is 16 characters or less. 2. Enter a name for the RAID set and press . 3.
5. Use the up/down arrow key to select a drive, and then press to select. A small triangle marks the selected drive. Press after completing your selection. 6. Use the up/down arrow key to select the strip size for the RAID array (for RAID 0, 10 and 5 only), and then press . The available strip size values range from 4 KB to 128 KB.
Deleting a RAID set Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2. Delete RAID Volume and press . The following screen appears: Name Volume0 [DELETE VOLUME MENU] Level Drives RAID0 (Stripe) 2 Capacity 298.0GB Status Normal Bootable Yes [HELP] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED.
Exiting the Intel® Rapid Storage Technology Option ROM utility To exit the utility: 1. From the utility main menu, select 6. Exit, then press . The following warning message appears: [CONFIRM EXIT] Are you sure you want to exit? (Y/N): 2. Press to exit or press to return to the utility main menu. 5.2 Creating a RAID driver disk 5.2.1 Creating a RAID driver disk in Windows® To install the RAID driver for Windows® OS: 1.
5-12 Chapter 5: RAID Configuration
Appendix Appendix A
W480/SYS block diagram A-2 Appendix
Q-Code table Code 00 02 03 04 06 10 11 – 14 15 – 18 19 – 1C 2B – 2F 30 31 32 – 36 37 – 3A 3B – 3E 4F 50 – 53 4F 54 55 56 57 58 59 5A 5B 5C – 5F E0 E1 E2 E3 E4 – E7 E8 E9 EA EB EC – EF F0 F1 F2 Description Not used microcode CACHE_ENABLED PCH initialization CPU_EARLY_INIT PEI Core is started Pre-memory CPU initialization is started Pre-memory System Agent initialization is started Pre-memory PCH initialization is started Memory initialization Reserved for ASL (see ASL Status Codes section below) Memory Inst
Code F4 Description Recovery firmware image is loaded F5 – F7 Reserved for future AMI progress codes F8 F9 Recovery PPI is not available Recovery capsule is not found FB – FF Reserved for future AMI error codes 60 DXE Core is started 61 NVRAM initialization 62 Installation of the PCH Runtime Services 63 – 67 CPU DXE initialization is started 68 PCI host bridge initialization 69 System Agent DXE initialization is started 6A System Agent DXE SMM initialization is started 6B – 6F System
Code A5 Description SCSI Reset A6 SCSI Detect A7 SCSI Enable A8 Setup Verifying Password A9 Start of Setup AA Reserved for ASL (see ASL Status Codes section below) AB Setup Input Wait AC Reserved for ASL (see ASL Status Codes section below) AD Ready To Boot event AE Legacy Boot event AF Exit Boot Services event B0 Runtime Set Virtual Address MAP Begin B1 Runtime Set Virtual Address MAP End B2 Legacy Option ROM Initialization B3 System Reset B4 USB hot plug B5 PCI bus hot plu
ACPI/ASL Checkpoints (under OS) A-6 Code Description 03 System is entering S3 sleep state 04 System is entering S4 sleep state 05 System is entering S5 sleep state 30 System is waking up from the S3 sleep state 40 System is waking up from the S4 sleep state AC System has transitioned into ACPI mode. Interrupt controller is in PIC mode. AA System has transitioned into ACPI mode. Interrupt controller is in APIC mode.
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Australia statement notice From 1 January 2012 updated warranties apply to all ASUS products, consistent with the Australian Consumer Law. For the latest product warranty details please visit https://www.asus.com/support/. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
India RoHS This product complies with the “India E-Waste (Management) Rules, 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01% by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax Web site Technical Support Telephone Online Support 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 https://www.asus.com +86-21-38429911 h ttps://www.asus.com/support/Product/ContactUs/Services/ questionform/?lang=en ASUSTeK COMPUTER INC. (Taiwan) Address Telephone Fax Web site 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 https://www.
ASUS contact information ASUS COMPUTER INTERNATIONAL (America) Address 48720 Kato Rd., Fremont, CA 94538, USA Fax +1-510-608-4555 Web site https://www.asus.com/us/ Technical Support Support fax General support Online support +1-812-284-0883 +1-812-282-2787 https://www.asus.com/support/Product/ContactUs/Services/ questionform/?lang=en-us ASUS COMPUTER GmbH (Germany and Austria) Address Web site Harkortstrasse 21-23, 40880 Ratingen, Germany https://www.asus.
ASUS contact information ASUS Holland BV (The Netherlands) Address Web site Marconistraat 2, 7825GD EMMEN, The Netherlands https://www.asus.com/nl/ Technical Support Telephone +31-(0)591-5-70292 Fax +31-(0)591-666853 E-mail advance.rma.eu@asus.com Online Support https://www.asus.com/support/Product/ContactUs/Services/ questionform/?lang=nl-nl ASUS Polska Sp. z o.o. (Poland) Address Web site Ul. Postępu 6, 02-676 Warszawa, Poland https://www.asus.
