PEI-10G/X710-2T 10 Gigabit/s Ethernet Dual Port User Guide
E20771 First Edition October 2022 Copyright © 2022 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Contents....................................................................................................................... iii About this guide.......................................................................................................... iv How this guide is organized.............................................................................iv Where to find more information........................................................................iv Conventions used in this guide...
About this guide This user guide contains the information you need when installing and configuring the Ethernet card. How this guide is organized This guide contains the following parts: • Chapter 1: Product Introduction This chapter describes the features of the Ethernet card and the new technologies it supports. • Chapter 2: Boot Agent Configuration This chapter provides instructions for configuring iSCSI.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
Specifications PEI-10G/X710-2T Form Factor Controller Host Interface Ports Power Consumption Dimensions Half-height, half-length Intel® X710-AT2 Ethernet controller PCIe 3.0x4 2 x 10Gb Base-T with RJ45 connectors Up to 9.5W PCB: 68.9 x 121 mm Pre-eXecution Environment (PXE) Management Features ACPI Energy Efficient Ethernet (IEEE 802.3az) vi • Please refer to www.asus.com for the latest AVL update. • Specifications are subject to change without notice.
Product Introduction This chapter describes the features of the Ethernet card and the new technologies it supports.
1.1 Welcome! Thank you for buying an ASUS® PEI-10G/X710-2T 10Gb/s Ethernet card! Before you start installing the Ethernet card, check the items in your package with the list below. 1.2 Package contents Check your package for the following items. Standard Gift Box Pack 1 Support DVD Standard Bulk Pack 1 (per carton) Low-Profile Bracket 1 1 Screws 2 2 1 (per carton) 5 (per carton) Packing Quantity If any of the above items is damaged or missing, contact your retailer. 1.
1.4 Card layout 1. RJ45 LAN Port 1 (LAN1) 2. RJ45 LAN Port 2 (LAN2) 3.
1.5 Replacing the card bracket The Ethernet card is bundled with a full-length bracket and a low-profile bracket. By default, the card is pre-installed with a full-length bracket. To replace the card bracket: 1. Place the Ethernet card on a flat and stable surface with the heatsink facing upwards. 2. Remove the two screws that secure the Ethernet card to the card bracket, then remove the card bracket. Default card bracket 1-4 3.
iSCSI Configuration This chapter provides instructions for configuring iSCSI 2
2.1 2-2 iSCSI Configuration 1. Turn on the system and enter BIOS Setup during POST. 2. Go to the Advanced menu > iSCSI Configuration, then press to display the iSCSI configuration menu. 3. Select iSCSI Initiator Name and press , then enter the iSCSI Initiator Name.
4. Select Add an Attempt and press , then select the MAC address that corresponds to the Ethernet card. 5. Fill in the configuration fields, then press to save changes and restart the system.
2-4 Chapter 2: iSCSI Configuration
Driver Installation This chapter provides instructions for installing the Ethernet card drivers on different operating systems.
3.1 Windows® Server OS Driver Installation To update the Ethernet card driver for Windows® Server OS: 3-2 1. Restart the system, then log on with Administrator privileges. 2. Insert the Support CD into the optical drive. The Support CD automatically displays the Drivers menu if Autorun is enabled. • If Windows® automatically detects the LAN controllers and displays a New Hardware Found window, click Cancel to close this window.
3.2 Linux OS Driver Installation To install the Ethernet card driver for Linux OS: 1. Navigate to the location of the driver in a terminal window, then unzip the driver: tar -xvf .tar.gz p12rm@p12rm-P12R:~/Desktop/Temp$ ls i40e-2.20.12.tar.gz license_gpl.txt readmefirst.txt p12rm@p12rm-P12R:~/Desktop/Temp$ tar -xvf i40e-2.20.12.tar.gz 2. Navigate to the folder containing the unzipped driver, then install the driver: make install p12rm@p12rm-P12R:~/Desktop/Temp$ cd i40e-2.20.
Simplified EU Declaration of Conformity English ASUSTeK Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of related Directives. Full text of EU declaration of conformity is available at: www.asus.com/support Français AsusTek Computer Inc. déclare par la présente que cet appareil est conforme aux critères essentiels et autres clauses pertinentes des directives concernées.
FCC COMPLIANCE INFORMATION Per FCC Part 2 Section 2.1077(a) Responsible Party: Address: Phone/Fax No: Asus Computer International 800 Corporate Way, Fremont, CA 94539 (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Model Number : 10G LAN Card PEI-10G/X710-2T compliance statement: This device complies with part 15 of the FCC Rules.
3-6 Chapter 3: Driver Installation
