User Guide

ManualsBrandsAsus ManualsServer AccessoriesPEB-10G/57811-1S

10 Gigabit/s Ethernet card

PEB-10G/57840-2S

PEB-10G Series

PEB-10G/57811-1S

User Guide

Summary of content (34 pages)

PAGE 1
PEB-10G Series PEB-10G/57840-2S PEB-10G/57811-1S 10 Gigabit/s Ethernet card User Guide
PAGE 2
E9427 First Edition June 2014 Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
PAGE 3
Contents Contents....................................................................................................................... iii About this guide.......................................................................................................... iv How this guide is organized.............................................................................iv Where to find more information........................................................................iv Conventions used in this guide...
PAGE 4
About this guide This user guide contains the information you need when installing and configuring the server management board. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the PEB-10G Series Ethernet card features and the new technologies it supports. • Chapter 2: Boot Agent configuration This chapter provides instructions on setting the Broadcom NetXtreme Ethernet Boot Agent.
PAGE 5
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
PAGE 6
PEB-10G Series specifications summary PEB-10G/57840-2S Speed & Ports Ethernet Controller PHY Connector & module type Host Interface Form factor PEB-10G/57811-1S 10 Gigabit/s Ethernet 10 Gigabit/s Ethernet Fiber; Dual Port Fiber; Single Port Broadcom 57840S Broadcom 57811S LC Fiber Optic Supports SFP+ SR Optical module, SFP+ LR Optical module, Direct Attached Copper* PCI-E Gen3 x8 PCI-E Gen2 x8 4.72 in. x 1.77 in. (lower than standard low profile) SMF up to 10km (LR) Support Cable Type MMF 62.
PAGE 7
Product introduction This chapter offers the PEB-10G Series Ethernet card features and the new technologies it supports.
PAGE 8
1.1 Welcome! Thank you for buying an ASUS® PEB-10G Series 10 Gigabit/s Ethernet card! Before you start installing the Ethernet card, check the items in your package with the list below. 1.2 Package contents Check your package for the following items.
PAGE 9
1.4 Card layout PEB-10G/57840-2S Front view Back view 1. LC Fiber Optic Connector 1 2. LC Fiber Optic Connector 2 3. PCI Express x8 interface 4. SFP2LED2 LED 5. SFP2LED1 LED 6.
PAGE 10
1.5 Replacing the card bracket The PEB-10G Series Ethernet card is bundled with a full-length bracket, a low-profile bracket, and an ASUS proprietary bracket. By default, the card is pre-installed with a full-length bracket. The proprietray bracket supports ASUS Z10PH-D16 series, ES4000 G3 series, and RS720Q-E8 series models, etc. The supported list of models are subject to change without prior notice. To replace the card bracket: 1.
PAGE 11
Boot Agent Configuration This chapter provides instructions on setting the Broadcom NetXtreme Ethernet Boot Agent.
PAGE 12
2.1 Broadcom NetXtreme Ethernet Boot Agent The Broadcom NetXtreme Ethernet Boot Agent provides hardware-based Ethernet card configurations. To start the Broadcom NetXtreme Ethernet Boot Agent and access the main screen: 1. Turn on the system. 2. During POST, press when the following screen appears. Broadcom NetXtreme Ethernet Boot Agent Copyright (C) 2000-2013 Broadcom Corporation All rights reserved. Press Ctrl-S to enter Configuration Menu 3.
PAGE 15
Boot Strap Type [Auto] Configuration options: [Auto] [BBS] [Int18h] [Int19h] Hide Setup Prompt [Disabled] Configuration options: [Disabled] [Enabled] Setup Key Stroke [Ctrl-S] Configuration options: [Ctrl-S] [Ctrl-B] Banner Message Timeout [10 Seconds] Configuration options: [1 Second] – [14 Seconds] Link Speed [10Gbps] Configuration options: [10Gbps] [1Gbps] Pre-boot Wake On LAN [Enabled] Configuration options: [Enabled] [Disabled] VLAN Mode [Disabled] Configuration options: [Disabled] [Enabled] VLA
PAGE 17
General Parameters TCP/IP Parameters via DHCP [Enabled] This option applies to IPv4. [Enabled] The iSCSI boot host software acquires the IP address from the DHCP server. [Disabled] The iSCSI boot host software acquires the static IP address. iSCSI Parameters via DHCP [Enabled] [Enabled] The iSCSI boot host software acquires its iSCSI target parameters from the DHCP server.
PAGE 18
[One Time D isabled] On the first system boot, the iSCSI boot host software does not attempt to boot from the iSCSI target. On subsequent system reboots, the iSCSI boot host software will attempt to boot from the iSCSI target. This option is useful when doing a remote install of the OS to an iSCSI target. • When using iSCSI boot, set Boot to iSCSI Target to [Disabled] or [One Time Disabled]. • When using iSCSI boot to install Windows Server 2008 OS, refer to http://support.microsoft.
PAGE 19
Initiator Parameters Key in the necessary parameters. CComprehensive Configuration Management v7.8.21 Copyright (C) 2000-2013 Broadcom Corporation All rights reserved. IP Address Subnet Mask Default Gateway Primary DNS Secondary DNS iSCSI Name CHAP ID CHAP Secret : : : : : : : : Initiator Parameters 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 iqn.1995-05.com.broadcom.
PAGE 21
Driver installation This chapter provides instructions for installing the Ethernet card drivers on different operating systems.
PAGE 22
3.1 Windows® Server OS Driver Installation To update the Ethernet card driver for Windows® Server OS: 3-2 1. Restart the computer, and then log on with Administrator privileges. 2. Insert the Support CD to the optical drive. The Support CD automatically displays the Drivers menu if Autorun is enabled in your computer. • If Windows® automatically detects the LAN controllers and displays a New Hardware Found window, click Cancel to close this window.
PAGE 23
5. Toggle I accept the terms in the license agreement and click Next to continue. 6. Follow the screen instructions to complete the installation. 7. If the Windows Security window appears during the driver installation, click Install this driver software anyway to continue.
PAGE 24
3-4 8. Click Finish to exit the installation wizard. 9. Restart the system.
PAGE 25
3.2 Linux OS Driver Installation To install the Ethernet card driver for Linux OS: 1. Within the Linux Terminal, install the source RPM package: rpm -ivh netxtreme2-.src.rpm For Red Hat Linux: For SuSE Linux: 2. CD to the RPM path and build the binary driver for your kernel: cd /usr/src/{redhat,OpenLinux,turbo,packages,rpm ..} (For RHEL 6.
PAGE 26
rpm -bb SPECS/netxtreme2.spec or (For RPM version 4.x.x) rpmbuild -bb SPECS/netxtreme2.spec Note that the RPM path is different for different Linux distributions. The driver will be compiled for the running kernel by default. To build the driver for a kernel different than the running one, specify the kernel by defining it in KVER: rpmbuild -bb SPECS/netxtreme2.spec --define “KVER ” in the form of 2.x.y-z is the version of another kernel that is installed on the system. 3.
PAGE 27
rpm -ivh RPMS//netxtreme2-..
PAGE 28
For SuSE Linux: 3-8 Chapter 3: Driver installation
PAGE 29
rpm -ivh RPMS/i386/netxtreme2-.i386.rpm Note that the --force option may be needed on some Linux distributions if conflicts are reported. The drivers will be installed in the following path: 2.4.x kernels: /lib/modules//kernel/drivers/net/bnx2.o /lib/modules//kernel/drivers/net/bnx2x.o 2.6.0 kernels: /lib/modules//kernel/drivers/net/bnx2.ko /lib/modules//kernel/drivers/net/bnx2x.ko 2.6.
PAGE 30
4. Unload existing driver if necessary: rmmod bnx2 rmmod bnx2x If the cnic driver is loaded, it should also be unloaded along with dependent drivers: rmmod bnx2fc rmmod bnx2i rmmod cnic 5. Load the bnx2 driver for the BCM5706/BCM5708/5709/5716 devices: insmod bnx2.o or insmod bnx2.ko (on 2.6.x kernels) or modprobe bnx2 To load the bnx2x driver for the BCM57710/BCM57711/BCM57711E/BCM57712 devices: insmod bnx2x.o or insmod bnx2x.ko (on 2.6.x kernels) or modprobe bnx2x To load the cnic driver: insmod cnic.
PAGE 31
insmod bnx2fc.ko or modprobe bnx2fc service bnx2fcd start Note that the inbox kernel may have an older version of bnx2, bnx2x and cnic driver. It is important for FCoE offload user to unload these inbox versions before attempting to load bnx2fc driver. You can do either of these two options: 6. a) Reboot the server.
PAGE 32
3-12 Chapter 3: Driver installation
PAGE 33
ASUS contact information ASUSTeK COMPUTER INC. Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 Telephone +886-2-2894-3447 Fax +886-2-2890-7798 E-mail info@asus.com.tw Web site http://www.asus.com Technical Support Telephone Fax Online Support +86-21-38429911 +86-21-58668722 ext: 9101 http://support.asus.com/techserv/techserv.aspx ASUSTeK COMPUTER INC.
PAGE 34
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Date : Signature : Representative Person’s Name : Jun. 20, 2014 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.