PE5100D Series Embedded Computer User Manual
E22859 First Edition February 2024 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual..............................................................................................................5 Conventions used in this manual.......................................................................................... 6 Package contents...............................................................................................................7 Chapter 1: Getting to know your Embedded Computer 1.1 Features.......................................................
3.9 Installing an mPCIe module.................................................................................60 3.10 Installing a nano SIM card.....................................................................................61 3.11 Installing antennas (optional)..............................................................................63 Chapter 4: Watchdog Timer 4.1 Watchdog Timer implementation......................................................................68 4.
About this manual This manual provides information about the hardware and software features of your Embedded Computer, organized through the following chapters: Chapter 1: Getting to know your Embedded Computer This chapter details the hardware components of your Embedded Computer. Chapter 2: Using your Embedded Computer This chapter provides you with information on using your Embedded Computer.
Conventions used in this manual To highlight key information in this manual, some text are presented as follows: IMPORTANT! This message contains vital information that must be followed to complete a task. NOTE: This message contains additional information and tips that can help complete tasks. WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Embedded Computer's data and components.
Package contents Your Embedded Computer package contains the following items: PE5100D Power terminal block Wall mount kit with dampers Remote power terminal block PE Series 7
Optional item(s)* Terminal block power adapter Power adapter and cord Cellular network antenna Wi-Fi antenna NOTE: • *These accessories are not bundled and need to be purchased separately. • Some bundled accessories may vary depending on the model. For details on these accessories, refer to their respective user manuals. • Illustrations of the device and accessories are for reference only. Actual product specifications may vary depending on the model.
Getting to know your Embedded Computer 1
1.1 Features 1.1.1 Front view HDMI™ port with cable lock The integrated HDMI (High Definition Multimedia Interface) port with a receptacle connector can support resolutions up to 4096 x 2160 @ 30 Hz on external display devices. NOTE: The cable lock helps to prevent disconnection caused by tension or vibration.
Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled. Dual-mode DisplayPort The DisplayPort 1.2 port can support resolutions up to 4096 x 2160 @ 60 Hz on external display devices. 2.5G LAN port The 8-pin RJ-45 LAN port for 10/100/1000/2500 Mbps connection to a Local Area Network (LAN).
Serial (COM) connector The 9-pin DB9 connector allows you to connect RS232/422/485 serial (COM) devices, such as bar code scanners, modems, and printers. Please refer to the table below for the pin definitions of the different COM connectors. NOTE: Default set to RS-232. Setting can be changed through the BIOS.
Serial (COM) connector The 9-pin DB9 connector allows you to connect RS-232 serial (COM) devices, such as bar code scanners, modems, and printers. Please refer to the table below for the pin definitions of the different COM connectors. 1 2 3 4 5 6 7 8 9 Pin RS-232 1 DCD# 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI Drive activity LED The drive activity LED lights up when your Embedded Computer is accessing the internal storage drive.
Power button The power button allows you to turn the Embedded Computer on or off. You can use the power button to put your Embedded Computer to sleep mode or press it for four (4) seconds to force shutdown your Embedded Computer. 2.5-inch hot-swap storage bay The 2.5-inch hot-swap storage bay allows you to install a 2.5-inch HDD/SSD and supports RAID 0/1. USB 10Gbps port The USB (Universal Serial Bus) 10Gbps port provides a transfer rate up to 10 Gbit/s.
1.1.2 Rear view Power input The power input jack allows you to connect the bundled power terminal block. Remote power connector The remote power connector allows you to connect an external power button or switch.
Serial (COM) connector The 9-pin DB9 connector allows you to connect RS-232 serial (COM) devices, such as bar code scanners, modems, and printers. Please refer to the table below for the pin definitions of the different COM connectors. 1 2 3 4 5 6 7 8 9 Pin RS-232 1 DCD# 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI USB 5Gbps port The USB (Universal Serial Bus) 5Gbps port provides a transfer rate up to 5 Gbit/s. USB 2.
Isolated DIO connector (optional) The Isolated Digital Input/Output (DIO) connector provides electrical isolation of digital input and output signals, which allow micro controllers to detect and output logic states. The high voltage protection can be used in industrial level uses. Please refer to the illustration below for the specification and pin definitions of the Isolated DIO connector.
1.1.3 Left view 1.1.4 Right view Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled.
1.2 Motherboard Overview Refer to the table on the next page for the page numbers of the numbered items. 1.2.
Jumpers COM +5V/+12V Selection jumper 21 2. Clear RTC RAM jumper 22 Connectors/slots 20 Page 1. Page 1. Mini PCIe slot 23 2. Battery connector 23 3. M.2 M-key slot 24 4. SATA 6Gb/s connector 25 5. SPI TPM connector 26 6. M.2 B-key slot 26 7. Nano SIM Card slot 27 8. M.2 E-key (Wi-Fi) slot 27 9. COM Debug connector 28 10. DC-in Power connector 29 11. DIMM slot 30 12. GPIO connector 30 13.
1.2.2 1. Onboard jumpers COM +5V/+12V Selection jumper The COM +5V/+12V Selection jumper allows you to select the voltage for the COM1 and COM2 ports.
2. Clear RTC RAM jumper The Clear RTC RAM jumper allows you to clear the Real Time Clock (RTC) RAM in the CMOS, which contains the date, time, system passwords, and system setup parameters. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds. 3. Plug the power cord and turn ON the computer. 4. Hold down the key during the boot process and enter BIOS setup to re-enter data.
1.2.3 1. Internal connectors Mini PCIe slot The Mini PCIe slot allows you to install a Mini PCIe peripheral device. NOTE: The Mini PCIe peripheral device is purchased separately. 2. RTC Battery connector The RTC Battery connector allows you to connect a lithium CMOS battery.
3. M.2 M-key slot The M.2 M-key slot allows you to install an M-key (PCIe Gen4 x4), type 2280 M.2 device, such as an M.2 SSD module. NOTE: The M.2 SSD module is purchased separately.
4. SATA 6Gb/s connector The SATA 6Gb/s allows you to connect SATA devices, such as optical disc drives and hard disk drives via a SATA cable. Connector type Wafer HD 7p, 1.27mm pitch NOTE: Ensure to use the bundled cable when connecting a storage device to this connector.
5. SPI TPM connector The SPI TPM connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. Connector type 6. Header 2x7p, K14, 2.0mm pitch M.2 B-key slot The M.2 B-key slot allows you to install a B-key (PCIe x1, USB 3.2 Gen 1, USB 2.0) type 3042/3052 M.2 device, such as a 4G LTE or 5G NR module. NOTE: The M.
7. Nano SIM Card slot The Nano SIM Card slot allows you to install a Nano SIM card. NOTE: Nano SIM cards are purchased separately. 8. M.2 E-key (Wi-Fi) slot The M.2 E-key (Wi-Fi) slot allows you to install an E-key (PCIe, USB 2.0) type 2230 M.2 Wi-Fi module. NOTE: The M.2 Wi-Fi module is purchased separately.
9. COM Debug connector The COM Debug connector allows you to connect a COM debug card. Connector type 28 PE Series Header 2x3p, 2.
10. DC-in 4-Pin Power connector The DC-in 4-pin Power connector is for DC power input. Using a compatible power cable and power board, you may connect a suitable power supply with DC-in jacks. Connector type POWER CON 4P W/P WARNING! Only connect a single power connector (EX_DCIN or DCIN power input) at a time, connecting both power connectors at the same time may cause damage to your Embedded Computer.
11. DIMM slot The motherboard comes with a Small Outline Dual Inline Memory Module (SODIMM) slot designed for DDR5 (Double Data Rate 5) memory modules. 12. GPIO connector The GPIO connector allows you to connect a general purpose input/ output module to customize digital signal input/output. Connector type 30 PE Series BOX header 2x5p, K9, 2.
13. I2C connector The I2C (Inter-Integrated Circuit) connector allows you to connect an I2C-compatible IoT security module. Connector type Header 1x3p, K6, 2.
PE Series
Using your Embedded Computer 2
2.1 Getting started 2.1.1 Connect the AC power adapter to your Embedded Computer To connect the AC power adapter to your Embedded Computer: A. Connect the power cord to the AC power adapter. B. Connect the AC power adapter to the terminal block power adapter. C. Connect the 3-pin terminal block DC power connector into your Embedded Computer’s power (DC) input. D. Plug the AC power adapter into a 100 V~240 V power source.
IMPORTANT! • We strongly recommend that you use only UL-certified power adapters and cables that meet the following requirements or ones that you purchased as an option with your Embedded Computer. 330 W Power adapter (operating temperature 0˚C to 40˚C) Input voltage: 100-240 Vac Input frequency: 50-60 Hz Output current: 13.75 A (330 W) Output voltage: 24 Vdc System (operating temperature -25˚C to 70˚C) Rated voltage: 8-48 Vdc Rated current: 41.25 A - 6.
2.1.2 Connect a display panel to your Embedded Computer You can connect a display panel or projector to your Embedded Computer that has the following connector(s): • HDMI™ connector • DisplayPort To connect a display panel to your Embedded Computer: Connect one end of an HDMI™ or a DisplayPort cable to an external display, and the other end of the cable to your Embedded Computer’s HDMI™ port or DisplayPort.
Connect display via DisplayPort PE Series 37
2.1.3 Connect the USB cable from keyboard or mouse You can connect generally any USB keyboard and mouse to your Embedded Computer. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your Embedded Computer: Connect the USB cable from your keyboard and mouse to any of the USB ports of your Embedded Computer. NOTE: • The keyboard varies with country and/or region. • The keyboard and mouse are purchased separately.
2.1.4 Turn on your Embedded Computer Press the power button to turn on your Embedded Computer if it does not power on automatically when you connect it to a power source.
2.2 Turning off your Embedded Computer If your Embedded Computer is unresponsive, press and hold the power button for at least four (4) seconds until your Embedded Computer turns off.
2.3 Installing wall mount brackets 1. Insert the eight (8) dampers bundled with the wall mount kit into the keyhole slots on the wall mount brackets and slide them into the narrower channel of each hole for secure placement. 2. Align the wall mount brackets to the screw holes on the bottom of your Embedded Computer, and then secure the wall mount brackets using the six (6) bundled screws.
PE Series
3 Upgrading your Embedded Computer
3.1 Installing a storage device Your may install up to two (2) 2.5-inch storage devices (hot-swappable, 7~7.5mm) to your Embedded Computer. 1. Loosen the two (2) screws securing each of the storage device trays to the right panel. 2. Pull the storage device tray out of the chassis. 3. Install your storage device to the storage device tray (A), then secure it with four (4) screws (B).
3.2 Removing the bottom cover IMPORTANT! • Ensure that your hands are dry before proceeding with the rest of the installation process. Before installing any of the features in this guide, use a grounded wrist strap or touch a safely grounded object or metal object to avoid damaging them due to static electricity. • Turn off the power of your Embedded Computer and allow it to cool for at least 10 minutes before performing any installation/ uninstallation process.
1. Turn off your Embedded Computer, and then disconnect all cables and peripherals. 2. Place the Embedded Computer on a flat stable surface with its top side facing down. 3. Remove the screws from the bottom cover, and then remove the bottom cover.
3.3 Replacing the bottom cover Align the screw holes on the bottom cover with those on your Embedded Computer’s chassis. Secure the bottom cover using the screws removed previously.
3.4 Removing the heat spreader 1. Follow the instructions in the Removing the bottom cover section to remove the bottom cover. 2. Follow steps 1-2 in the Installing a storage device section to remove the storage device trays.
3. Remove the eight (8) screws securing the two (2) storage connector brackets, and set the brackets aside without disconnecting the SATA cables.
4. Remove the six (6) screws securing the heat spreader. 5. Carefully remove and set aside the heat spreader, making sure that the thermal pads on it do not come in contact with any surfaces.
3.5 Installing memory modules Your Embedded Computer comes with two (2) SO-DIMM memory slots that allow you to install DDR5 SO-DIMMs, ECC*, with a maximum of 64 GB. To install a memory module: 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. Align and insert a memory module into one of the two SO-DIMM memory slots in the chassis. 3. Press down until the memory module is securely seated in place. 4.
3.6 Installing an M.2 SSD module to the M.2 M-key slot Your Embedded Computer comes with an M.2 M-key slot that allows you to install an M.2 (M-key, supports 2280 PCIe Gen4 x4) SSD module. To install an M.2 SSD module: 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. Align and insert the M.2 SSD module into its slot inside the Embedded Computer. 3. Gently push down the module on top of the standoff and fasten it using a screw.
3.7 Installing a wireless card to the M.2 E-key slot Your Embedded Computer comes with an M.2 E-key slot that allow you to install an M.2 (E-key, Wi-Fi / Bluetooth) wireless module. WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. To install an M.2 wireless module: 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. Remove the screw from the M.
WIFI 2 WIFI 1 WIFI 2 WIFI 1 54 PE Series
3.8 Installing a cellular network module to the M.2 B-key slot Your Embedded Computer comes with an M.2 B-key slot that allows you to install a B-key (PCIe x1/USB 3.2 Gen 1/USB2.0, type 3042/3052) M.2 device, such as a 4G LTE or 5G NR module. WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. To install a 4G LTE module: 1.
AUX MAIN AUX MAIN 56 PE Series
NOTE: • Refer to Installing antennas for more information on installing the antennas. • Connecting antennas to your module may strengthen the signal. • A soft clicking sound indicates that the antenna has been securely attached on the module.
To install a 5G NR module: WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. Remove the screw from the M.2 standoff. 3. If the standoff is already seated in the right mounting hole to fit your module, skip to step 5. 4.
AUX 0 MAIN 3 AUX 2 MAIN 1 AUX 0 MAIN 1 AUX 2 MAIN 3 PE Series 59
3.9 Installing an mPCIe module Your Embedded Computer comes with an mPCIe slot that allows you to install an mPCIe add-on module, such as a CANbus module. To install an mPCIe module: 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. Remove the two (2) screws from the standoffs. 3. Align and insert the module into the slot. 4. Press down, and then secure it in place using the two (2) screws previously removed. 5.
3.10 Installing a nano SIM card Your Embedded Computer comes with two (2) nano SIM card slots. NOTE: Nano SIM cards are purchased separately. To install a nano SIM card: 1. Follow the steps in the Removing the heat spreader section to remove the bottom cover and heat spreader. 2. (Optional) Remove the M.2 module from the M.2 B-key slot, if one is installed, by first removing the screw securing the module, and then removing the module. 3. Push the nano SIM cover in the direction towards the M.
PE Series
3.11 Installing antennas (optional) You may install antennas to the six (6) antenna jacks located on the front and right sides of your Embedded Computer. The installed antennas can be connected to the 4G LTE or 5G NR module installed in the M.2 B-key slot and to the wireless card installed in the M.2 E-key Wi-Fi slot. NOTE: It is recommended that you refer to the illustration that corresponds to the module(s) you have installed in your Embedded Computer.
For 5G NR module For 5G NR For wireless card For Wi-Fi 64 PE Series
To install an antenna: NOTE: If your Embedded Computer came pre-installed with antenna jacks, skip to step 9. 1. Remove the bottom cover. Refer to Removing the bottom cover for details. 2. (Optional) To install the antennas on the front panel for 5G NR modules, you will also need to remove the front panel by removing the two (2) screws securing it to the chassis. 3. Prepare the RF connector and cable. 4. Remove the rubber caps from the antenna holes. 5.
8. (Optional) For RF cables that need to connected to the front panel, route them to the 5G NR module through the two cutouts on the motherboard. 9. Connect the other end of the RF connector and cable to your wireless card (refer to Installing a wireless card to the M.2 E-key slot for details) or to your cellular network module (refer to Installing a cellular network module to the M.2 B-key slot for details). 10. Replace the bottom cover. Refer to Replacing the bottom cover for details. 11.
Watchdog Timer 4
4.1 Watchdog Timer implementation The Watchdog Timer used in this Embedded Computer is the POST Watchdog Timer. The Watchdog Timer circuit is in SuperIO and can be controlled by the BIOS setup menu through the system BIOS for different boot phases. Please refer to the table below for more details on the implementation of the Watchdog Timer. Watchdog timer POST Watchdog Timer Implementation This Watchdog Timer is for recovering the system from crashes during BIOS takeover to OS.
4.2 Watchdog Timer programming Please refer to the pseudo code for the NCT6116D watchdog timer programming below: SIO_INDEX_PORT is 0x2E SIO_DATA_PORT is 0x2F 1.
2. Set WDT Time Outportb(SIO_INDEX_PORT, 0x87); // Unlock SIO Outportb(SIO_INDEX_PORT, 0x87); // Unlock SIO Outportb(SIO_INDEX_PORT, 0x07); Outportb(SIO_DATA_PORT, 0x08); Outportb(SIO_INDEX_PORT, 0xF1); Outportb(SIO_DATA_PORT, Time); // Write WDT time, value 1 to 255 Outportb(SIO_INDEX_PORT, 0xAA); // Lock SIO 3.
4.
PE Series
Appendix
Safety information Your Embedded Computer is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • • • 74 Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface.
Care during use • • • • • Do not walk on the power cord or allow anything to rest on it. Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still flows. Always unplug the power cord from the power outlets before cleaning the system. Use this product with care when operating at full load, as the product, especially the outer casing, may reach elevated temperatures.
Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users DO NOT throw the Embedded Computer in municipal waste. This product has been designed to enable proper reuse of parts and recycling.
Regulatory notices FCC Compliance Information Responsible Party: Asus Computer International Address: Phone / Fax No: 48720 Kato Rd., Fremont, CA 94538, USA (510)739-3777 / (510)608-4555 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Safety Precautions Accessories that came with this product have been designed and verified for the use in connection with this product. Never use accessories for other products to prevent the risk of electric shock or fire.
Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements. Please refer to https://csr.asus.com/Compliance.
Türkiye RoHS AEEE Yönetmeliğine Uygundur ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to https:// csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
甲類警語 警告：為避免電磁干擾，本產品不應安裝或使用於住宅環境。 China Compulsory Certification 警告：在居住環境中，運行此設備可能會造成無線電干扰。 「產品之限用物質含有情況」之相關資訊，請參考下表： Taiwan Declaration of Restricted Substances Marking 限用物質及其化學符號 (Restricted substances and its chemical symbols) 單元 (Unit) 印刷電路板 及電子組件 鉛 汞 鎘 Lead (Pb) Mercury (Hg) Cadium (Cd) 六價鉻 多溴聯苯 多溴二苯醚 － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ Hexavalent Polybrominated Polybrominated chromium biphenyls diphenyls ethers (Cr+6) (PBB) (PBDE) PCB
UK: The Radio Equipment Regulations 2017 (S.I. 2017/1206) Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
Опростена декларация за съответствие на ЕС С настоящото ASUSTek Computer Inc. декларира, че това устройство е в съответствие със съществените изисквания и другите приложими постановления на свързаната Директива 2014/53/EC. Пълният текст на ЕС декларация за съвместимост е достъпен на адрес https://www.asus.
הצהרת תאימות רגולטורית מקוצרת עבור האיחוד אירופי 2014/53/ מצהירה בזאת כי מכשיר זה תואם לדרישות החיוניות ולשאר הסעיפים הרלוונטיים של תקנהASUSTek Computer Inc. : ניתן לקרוא את הנוסח המלא של הצהרת התאימות הרגולטורית עבור האיחוד האירופי בכתובת.EU https://www.asus.com/support/ לשימוש בתוך מבנים סגורים בארצות המפורטות ברשימה5150-5350MHz הפועלות ברצועת התדריםWi-Fi יש להגביל רשתות :הבאה Egyszerűsített EU megfelelőségi nyilatkozat Az ASUSTek Computer Inc.
Zjednodušené vyhlásenie o zhode platné pre EÚ Spoločnosť ASUSTek Computer Inc. týmto vyhlasuje, že toto zariadenie je v súlade so základnými požiadavkami a ďalšími príslušnými ustanoveniami smernice č. 2014/53/EÚ. Plné znenie vyhlásenia o zhode pre EÚ je k dispozícii na lokalite https://www.asus.com/support/ Činnosť WiFi v pásme 5150 - 5350 MHz bude obmedzená na použitie vo vnútornom prostredí pre krajiny uvedené v tabuľke nižšie: nostavljena izjava EU o skladnosti ASUSTek Computer Inc.
Service and Support Visit our multi-language website at https://www.asus.com/support/.
PE Series
