PE1000S Series Embedded Computer User Manual
E22802 First Edition January 2024 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual..............................................................................................................5 Conventions used in this manual.......................................................................................... 6 Package contents...............................................................................................................7 Chapter 1: Getting to know your Embedded Computer 1.1 Features.......................................................
3.9 Installing wall mount brackets (optional).......................................................61 3.10 Mounting to a surface (optional).......................................................................62 Chapter 4: Watchdog Timer 4.1 Watchdog Timer implementation......................................................................64 4.2 Watchdog Timer programming..........................................................................65 Appendix Safety information............................
About this manual This manual provides information about the hardware and software features of your Embedded Computer, organized through the following chapters: Chapter 1: Getting to know your Embedded Computer This chapter details the hardware components of your Embedded Computer. Chapter 2: Using your Embedded Computer This chapter provides you with information on using your Embedded Computer.
Conventions used in this manual To highlight key information in this manual, some text are presented as follows: IMPORTANT! This message contains vital information that must be followed to complete a task. NOTE: This message contains additional information and tips that can help complete tasks. WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Embedded Computer's data and components.
Package contents Your Embedded Computer package contains the following items: PE1000S PE1000S-POE Power terminal block 1-to-3 COM port cable DIN rail clip PE Series 7
Optional item(s) Cellular network antenna Wi-Fi antenna Wall mount kit with two (2) brackets Power adapter and cord NOTE: • Some bundled accessories may vary depending on the model. For details on these accessories, refer to their respective user manuals. • Illustrations of the device and accessories are for reference only. Actual product specifications may vary depending on the model.
Getting to know your Embedded Computer 1
1.1 Features 1.1.
USB 2.0 port The USB (Universal Serial Bus) port is compatible with USB 2.0 or USB 1.1 devices, such as keyboards, pointing devices, flash disk drives, external HDDs, speakers, cameras, and printers. Power LED The power LED lights up when your Embedded Computer is turned on and blinks slowly when in sleep mode. Drive activity LED The drive activity LED lights up when your Embedded Computer is accessing the internal storage drive. Watchdog LED The watchdog LED lights up when a watchdog time out event occurs.
System reset pinhole The hard reset pinhole allows you to reboot your Embedded Computer. Serial (COM) connector The 9-pin DB9 connector allows you to connect one (1) RS422/485 device or three (3) RS-232 devices in conjunction with the bundled 1-to-3 COM port cable. Serial (COM) devices include bar code scanners, modems, and printers. Please refer to the table below for the pin definitions of the different COM connectors. NOTE: Default set to RS-232. Setting can be changed through the BIOS.
HDMI™ 1.4 port The integrated HDMI (High Definition Multimedia Interface) port with a receptacle connector can support resolutions up to 4096 x 2160 @ 30 Hz on external display devices. DisplayPort The DisplayPort 1.2a port can support resolutions up to 4096 x 2160 @ 60 Hz on external display devices. LAN port with cable lock The Intel i226 (2.5 GbE) Gigabit Ethernet controller with 8-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network and PXE boot.
1.1.2 Rear view PE1000S PE1000S-POE DIN rail clip mounting hole The DIN rail clip mounting hole allows you to secure a DIN rail clip to your Embedded Computer, so you can attach it to a DIN rail system.
1.1.
Power input The power input jack allows you to connect the bundled power terminal block. Serial (COM) connector The 9-pin DB9 connector allows you to connect RS232/422/485 serial (COM) devices, such as bar code scanners, modems, and printers. Please refer to the table below for the pin definitions of the different COM connectors. NOTE: Default set to RS-232. Setting can be changed through the BIOS.
Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled. Functional earth ground The functional earth ground provides you with a grounding point. Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled.
1.1.
Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled. Wireless antenna jack The wireless antenna jack allows you to connect a wireless antenna. NOTE: Wireless antennas are optional and may not come bundled. Serial (COM) connector (on selected PE1000S models) The 9-pin DB9 connector allows you to connect RS-232 serial (COM) devices that have serial ports, such as bar code scanners, modems, and printers.
GPIO connector (on selected PE1000S models) The 9-pin GPIO (General-purpose Input/Output) connector allows you to program it for input or output use, such as lighting control, door control, or alarm control. Please refer to the table below for the pin definitions of the connector.
1.2 Motherboard Overview Refer to the table on the next page for the page numbers of the numbered items. 1.2.1 Motherboard layout U2_1_2 LAN1 LAN2 U32G1_1_2 U32G2_1_2 COM2_3_4 HDMI_DP PWRBTN M2_M BATT_CON 2280 M2_B 10 9 8 COM5_6 COM1 SATA6G M2_E 7 DC_PWR DIO SODIMM_A1 3042 3052 CLRTC SIM IO_BTB_01 1 1.2.
Jumpers/switches Page Motherboard 1. Clear RTC RAM jumper 23 PoE LAN module 2. Boot switch Connectors/slots 24 Page Motherboard 1. SATA connector 25 2. M.2 E-key (Wi-Fi) slot 26 3. M.2 B-key slot 26 4. Nano SIM Card slot 27 5. DIMM slot 27 6. PoE LAN BTB connector 28 7. GPIO connector 29 8. Serial Port connector 30 9. Battery connector 30 10. M.2 M-key slot 31 PoE LAN module (available as an option on PE1000S-POE) 11.
1.2.3 1. Onboard jumpers & switches Clear RTC RAM jumper The Clear RTC RAM jumper allows you to clear the Real Time Clock (RTC) RAM in the CMOS, which contains the date, time, system passwords, and system setup parameters. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds. 3. Plug the power cord and turn ON the computer. 4.
2. Boot Mode switch (available as an option on PE1000S-POE) The Boot Mode switch allows you to enable your Embedded Computer to power on when the ignition is turned on. NOTE: To enable ignition control, you need to first set Restore Power Loss to S0 in the BIOS setup (refer to the APM Configuration section for details on this BIOS item), power off your Embedded Computer, and then set this switch to Enabled.
1.2.4 1. Internal connectors SATA 6Gb/s connector The SATA 6Gb/s allows you to connect SATA devices, such as optical disc drives and hard disk drives via a SATA cable. SATA6G Gold fingers Connector type Wafer HD 7p, 1.27mm pitch IMPORTANT! Ensure the SATA cable is inserted in the correct orientation with the gold fingers facing the left panel where the power button is located. NOTE: Ensure to use the bundled cable when connecting a storage device to this connector.
2. M.2 E-key (Wi-Fi) slot The M.2 E-key (Wi-Fi) slot allows you to install an E-key (PCIe, USB 2.0, I2C and PCM), type 2230 M.2 Wi-Fi module. NOTE: The M.2 Wi-Fi module is purchased separately. 3. M.2 B-key slot The M.2 B-key slot allows you to install a B-key (USB2.0) type 3042/3052 M.2 device, such as a 4G LTE or 5G NR module. NOTE: The M.2 4G LTE or 5G NR module is purchased separately.
4. Nano SIM Card slot The Nano SIM Card slot allows you to install a Nano SIM card. NOTE: The Nano SIM card is purchased separately. 5. DIMM slot The motherboard comes with a Small Outline Dual Inline Memory Module (SODIMM) slot designed for DDR4 (Double Data Rate 4) memory modules.
6. PoE LAN BTB connector (available only on PE1000S-POE) The PoE LAN BTB connector allows you to install a PoE LAN module. PoE LAN module IO_BTB_01 IO_BTB_02 7. GPIO connector The GPIO connector allows you to connect a general purpose input/ output module to customize digital signal input/output. Connector type 28 PE Series BOX header 2x5p, K9, 2.
8. Serial Port connector The Serial (COM) Port connector allows you to connect a serial port module. Connect the serial port module cable to this connector, then install the module to a slot opening on the system chassis. COM5_DCD# COM5_RXD COM5_TXD COM5_DTR# GND COM5_DSR# COM5_RTS# COM5_CTS# COM5_RI# NC COM6_DCD# COM6_RXD COM6_TXD COM6_DTR# GND COM6_DSR# COM6_RTS# COM6_CTS# COM6_RI# NC COM5_6 Connector type BOX header 2x10p, K10, 2.0mm pitch NOTE: • The serial port module is purchased separately.
9. RTC Battery connector The RTC Battery connector allows you to connect a lithium CMOS battery. 10. M.2 M-key slot The M.2 M-key slot allows you to install an M-key (PCIe and SATA), type 2280 M.2 device, such as an M.2 SSD module. NOTE: The M.2 SSD module is purchased separately.
11. Motherboard BTB connector (available only on PE1000S-POE) The motherboard BTB connector allows you to install the PoE LAN module to a motherboard that supports PoE LAN.
PE Series
Using your Embedded Computer 2
2.1 Getting started 2.1.1 Connect the AC power adapter to your Embedded Computer To connect the AC power adapter to your Embedded Computer: A. Connect the power cord to the AC power adapter. B. Connect the 3-pin terminal block DC power connector into your Embedded Computer’s power (DC) input. C. Plug the AC power adapter into a 100 V~240 V power source. NOTE: The power adapter is purchased separately and may vary in appearance, depending on model and your region.
IMPORTANT! • We strongly recommend that you use only UL-certified power adapters and cables that meet the following requirements or ones that you purchased as an option with your Embedded Computer. 160 W Power adapter Input voltage: 100 - 240 Vac Input frequency: 50 - 60 Hz Output current: 8 A (160 W) Output voltage: 20 Vdc System (operating temperature -25 to 60˚C) Rated voltage: 9 - 36 Vdc Rated current: 17.77 A - 4.
2.1.2 Connect a display panel to your Embedded Computer You can connect a display panel or projector to your Embedded Computer that has the following connector(s): • HDMI™ connector • DisplayPort To connect a display panel to your Embedded Computer: Connect one end of an HDMI™ or a DisplayPort cable to an external display, and the other end of the cable to your Embedded Computer’s HDMI™ port or DisplayPort.
Connect display via DisplayPort PE Series 37
2.1.3 Connect the USB cable from keyboard or mouse You can connect generally any USB keyboard and mouse to your Embedded Computer. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your Embedded Computer: Connect the USB cable from your keyboard and mouse to any of the USB ports of your Embedded Computer. NOTE: • The keyboard varies with country and/or region. • The keyboard and mouse are purchased separately.
2.1.4 Turn on your Embedded Computer Press the power button to turn on your Embedded Computer if it does not power on automatically when you connect it to a power source.
2.2 Turning off your Embedded Computer If your Embedded Computer is unresponsive, press and hold the power button for at least four (4) seconds until your Embedded Computer turns off.
3 Upgrading your Embedded Computer
3.1 Removing the bottom cover IMPORTANT! • Ensure that your hands are dry before proceeding with the rest of the installation process. Before installing any of the features in this guide, use a grounded wrist strap or touch a safely grounded object or metal object to avoid damaging them due to static electricity. • Turn off the power of your Embedded Computer and allow it to cool for at least 10 minutes before performing any installation/ uninstallation process.
3.2 Replacing the bottom cover Align the screw holes on the bottom cover with those on your Embedded Computer’s chassis. Secure the bottom cover using the screws removed previously.
3.3 Installing memory modules Your Embedded Computer comes with an SO-DIMM slot that allows you to install DDR4 SO-DIMMs. 1. Remove the bottom cover. Refer to the Removing the bottom cover section for instructions. 2. Remove the screws located on all four sides of your Embedded Computer as shown in the illustration (A). For PE1000S-POE, you will need to also remove the screws securing the PoE LAN module (B).
PE1000S-POE PoE LAN module PE Series 45
3. Remove the two (2) L-shaped metal frames, and then remove the three (3) screws securing the heat spreader to the motherboard and heatsink assembly. 4. Align and insert the memory module into the slot (A) and press it down (B) until it is securely seated in place.
3.4 Installing an M.2 SSD module to the M.2 M-key slot Your Embedded Computer comes with an M.2 M-key slot that allows you to install an M.2 (M-key, supports 2280 PCIe x2) SSD module. To install an M.2 SSD module: 1. Follow steps 1-2 in the Installing memory modules section to access the M.2 M-key slot. 2. Remove the screw securing the wireless module (A), and replace it with a standoff (B).
3. Align and insert the M.2 SSD into its slot inside the Embedded Computer. 4. Gently push down the M.2 SSD on top of the standoff and fasten it using a screw.
3.5 Installing a wireless card to the M.2 E-key slot Your Embedded Computer comes with an M.2 E-key slot that allow you to install an M.2 wireless (Wi-Fi / Bluetooth) module. To install an wireless module: 1. Follow steps 1-3 in the Installing memory modules section to access the M.2 E-key slot. 2. Remove the screw from the M.2 standoff. 3. Align and insert the wireless card into its slot inside the Embedded Computer. 4.
WARNING! RF modules are intended for OEM or host integrators only. For availability of system level RF certification, check with your OEM integrator. NOTE: • Please refer to the Installing antennas section for more information on installing the antennas. • Connecting antennas to your wireless card may strengthen the wireless signal. • A soft clicking sound indicates that the antenna has been securely attached on the wireless card.
3.6 Installing a cellular network module to the M.2 B-key slot Your Embedded Computer comes with an M.2 B-key slot that allows you to install a B-key (USB2.0, type 3042/3052) M.2 device, such as a 4G LTE or 5G NR module. To install a 4G LTE module: 1. Follow steps 1-2 in the Installing memory modules section to access the M.2 B-key slot. 2. Remove the screw from the M.2 standoff. 3. If the standoff is already seated in the right mounting hole to fit your module, skip to step 5. 4.
4G LTE module without wireless card LTE_AUX(D/G) LTE_MAIN LTE_MAIN LTE_AUX(D/G) 4G LTE module with wireless card WLAN_AUX(DIV) WLAN_MAIN WLAN_AUX(DIV) WLAN_MAIN LTE_AUX(D/G) LTE_MAIN LTE_AUX(D/G) LTE_MAIN 52 PE Series
NOTE: • To enable the hot-plug function of your 4G LTE module, click the weston-terminal icon in the upper left corner of your screen, and type the first command below when prompted: mm_cli sim-detect 1 mm_cli sim-detect 0 mm_cli sim-detect (enable hot-plug function) (disable hot-plug function) (display current setting) • Refer to Installing antennas for more information on installing the antennas. • Connecting antennas to your module may strengthen the signal.
To install a 5G NR module: 1. Follow steps 1-2 in the Installing memory modules section to access the M.2 B-key slot. 2. Remove the screw from the M.2 standoff. 3. If the standoff is already seated in the right mounting hole to fit your module, skip to step 5. 4. Unscrew the standoff, and install it to a mounting hole that matches the length of your module. 5. Align and insert the module into the slot. 6. Press down, and then secure it in place using the screw previously removed. 7.
5G_ANT1 (M1) 5G_ANT2 (M2) 5G_ANT0 (M) 5G_ANT3 (D/G) 5G_ANT3 (D/G) 5G_ANT2 (M2) 5G_ANT1 (M1) 5G_ANT0 (M) PE Series 55
3.7 Installing antennas (optional) You may install antennas to the four (4) antenna jacks located on the two sides of your Embedded Computer. The installed antennas can be connected to the 4G LTE or 5G NR module installed in the M.2 B-key slot and to the wireless card installed in the M.2 E-key Wi-Fi slot. NOTE: It is recommended that you refer to the illustration that corresponds to the module(s) you have installed in your Embedded Computer.
For 5G NR module For 5G NR For 5G NR For 4G LTE module with wireless card For Wi-Fi For 4G LTE PE Series 57
To install an antenna: NOTE: If your Embedded Computer came pre-installed with antenna jacks, skip to step 8. 1. Remove the bottom cover. Refer to Removing the bottom cover for details. 2. Follow steps 1-2 in the Installing memory modules section to access the antenna holes. 3. Prepare the RF connector and cable. 4. Remove the rubber caps from the antenna holes. 5. Insert the antenna jack end of the RF connector and cable into the antenna jack from within the chassis outwards. 6.
PE Series 59
3.8 Installing a DIN rail clip 1. Align the screw holes on the DIN rail clip to the ones on your Embedded Computer’s (refer to the Rear view section for the location of the DIN rail clip mounting holes). 2. Secure the DIN rail clip to your Embedded Computer using the screws bundled with the DIN rail clip. 3. Clip the final assembly to a DIN rail by hooking the DIN rail clip to the top of the DIN rail and then pressing down until you hear the clip snap into place.
3.9 Installing wall mount brackets (optional) 1. Remove the four (4) rubber feet screws (A), and then remove the rubber feet from them (B). 2. Align the wall mount brackets to the rubber feet screw holes, and then secure the wall mount brackets to your Embedded Computer using the rubber feet screws.
NOTE: • The wall mount brackets are compatible with most DIN rail clips available on the market. • The rubber feet screws and wall mount bracket screws are the same screws. 3.10 Mounting to a surface (optional) You can install your Embedded Computer to a suitable surface using wall mount brackets. 1. Make sure that the wall mount brackets are already installed. Refer to the section Installing wall mount brackets for installation instructions. 2.
Watchdog Timer 4
4.1 Watchdog Timer implementation The Watchdog Timer used in this Embedded Computer is the POST Watchdog Timer. The Watchdog Timer circuit is in SuperIO and can be controlled by the BIOS setup menu through the system BIOS for different boot phases. Please refer to the table below for more details on the implementation of the Watchdog Timer. Watchdog timer POST Watchdog Timer Implementation This Watchdog Timer is for recovering the system from crashes during BIOS takeover to OS.
4.2 Watchdog Timer programming Please refer to the pseudo code for the NCT6116D watchdog timer programming below: SIO_INDEX_PORT is 0x2E SIO_DATA_PORT is 0x2F 1.
2. Set WDT Time Outportb(SIO_INDEX_PORT, 0x87); // Unlock SIO Outportb(SIO_INDEX_PORT, 0x87); // Unlock SIO Outportb(SIO_INDEX_PORT, 0x07); Outportb(SIO_DATA_PORT, 0x08); Outportb(SIO_INDEX_PORT, 0xF1); Outportb(SIO_DATA_PORT, Time); // Write WDT time, value 1 to 255 Outportb(SIO_INDEX_PORT, 0xAA); // Lock SIO 3.
4.
PE Series
Appendix
Safety information Your Embedded Computer is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • • • 70 Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface.
Care during use • • • • • Do not walk on the power cord or allow anything to rest on it. Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still flows. Always unplug the power cord from the power outlets before cleaning the system. Use this product with care when operating at full load, as the product, especially the outer casing, may reach elevated temperatures.
Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users DO NOT throw the Embedded Computer in municipal waste. This product has been designed to enable proper reuse of parts and recycling.
Regulatory notices FCC Compliance Information Responsible Party: Asus Computer International Address: Phone / Fax No: 48720 Kato Rd., Fremont, CA 94538, USA (510)739-3777 / (510)608-4555 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Safety Precautions Accessories that came with this product have been designed and verified for the use in connection with this product. Never use accessories for other products to prevent the risk of electric shock or fire.
Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements. Please refer to https://csr.asus.com/Compliance.
Türkiye RoHS AEEE Yönetmeliğine Uygundur ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to https:// csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
甲類警語 警告：為避免電磁干擾，本產品不應安裝或使用於住宅環境。 China Compulsory Certification 警告：在居住環境中，運行此設備可能會造成無線電干扰。 「產品之限用物質含有情況」之相關資訊，請參考下表： Taiwan Declaration of Restricted Substances Marking 限用物質及其化學符號 (Restricted substances and its chemical symbols) 單元 (Unit) 印刷電路板 及電子組件 鉛 汞 鎘 Lead (Pb) Mercury (Hg) Cadium (Cd) － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ － ○ ○ ○ ○ ○ 六價鉻 多溴聯苯 多溴二苯醚 Hexavalent Polybrominated Polybrominated chromium biphenyls diphenyls ethers (Cr+6) (PBB) (PBDE) PCB
UK: The Radio Equipment Regulations 2017 (S.I. 2017/1206) Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
Опростена декларация за съответствие на ЕС С настоящото ASUSTek Computer Inc. декларира, че това устройство е в съответствие със съществените изисквания и другите приложими постановления на свързаната Директива 2014/53/EC. Пълният текст на ЕС декларация за съвместимост е достъпен на адрес https://www.asus.
הצהרת תאימות רגולטורית מקוצרת עבור האיחוד אירופי 2014/53/ מצהירה בזאת כי מכשיר זה תואם לדרישות החיוניות ולשאר הסעיפים הרלוונטיים של תקנהASUSTek Computer Inc. : ניתן לקרוא את הנוסח המלא של הצהרת התאימות הרגולטורית עבור האיחוד האירופי בכתובת.EU https://www.asus.com/support/ לשימוש בתוך מבנים סגורים בארצות המפורטות ברשימה5150-5350MHz הפועלות ברצועת התדריםWi-Fi יש להגביל רשתות :הבאה Egyszerűsített EU megfelelőségi nyilatkozat Az ASUSTek Computer Inc.
Zjednodušené vyhlásenie o zhode platné pre EÚ Spoločnosť ASUSTek Computer Inc. týmto vyhlasuje, že toto zariadenie je v súlade so základnými požiadavkami a ďalšími príslušnými ustanoveniami smernice č. 2014/53/EÚ. Plné znenie vyhlásenia o zhode pre EÚ je k dispozícii na lokalite https://www.asus.com/support/ Činnosť WiFi v pásme 5150 - 5350 MHz bude obmedzená na použitie vo vnútornom prostredí pre krajiny uvedené v tabuľke nižšie: nostavljena izjava EU o skladnosti ASUSTek Computer Inc.
Service and Support Visit our multi-language website at https://www.asus.com/support/.
PE Series
