Motherboard P5CR-L(S)
E1778 First Edition V1 March 2005 Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Contents ............................................................................................. iii Notices ................................................................................................ vi Safety information ............................................................................. vii About this guide ............................................................................... viii P5CR-L(S) specifications summary ....................................................
Contents Chapter 3: Powering up 3.1 3.2 Starting up for the first time ................................................ 3-1 Powering off the computer .................................................. 3-2 3.2.1 Using the OS shut down function ........................... 3-2 3.2.2 Using the dual function power switch .................... 3-2 Chapter 4: BIOS setup 4.1 4.2 4.3 4.4 iv Managing and updating your BIOS ........................................ 4-1 4.1.1 Creating a bootable floppy disk ......
Contents 4.5 4.6 4.7 Power menu ........................................................................ 4-29 4.5.1 ACPI APIC Support ................................................ 4-29 4.5.2 APM Configuration ................................................ 4-30 4.5.3 Hardware Monitor ................................................. 4-31 Boot menu .......................................................................... 4-33 4.6.1 Boot Device Priority ..............................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
P5CR-L(S) specifications summary CPU LGA775 socket for Intel® Pentium® 4 processor with Extended Memory 64-bit Technology (EM64T) Supports Intel® Hyper-Threading Technology Chipset Northbridge: Intel® E7221 Memory Controller Hub (MCH) Southbridge: Intel® ICH6R PCI/PCI-X bridge: Intel® 6702 PXH Front Side Bus 800/533 MHz Memory Dual-channel memory architecture 4 x 240-pin DIMM sockets support unbuffered ECC/ non-ECC 533/400 MHz DDR2 memory modules Supports 256 MB up to 4 GB of system memory Expansion
P5CR-L(S) specifications summary Special features ASUS Smart Fan ASUS CrashFree BIOS 2 ASUS Multi-Language BIOS ASUS MyLogo2™ ASUS EZ FLash BIOS features AMI BIOS, 8 MB FWH, Green, PnP, DMI2.0a, WfM2.0., ACPI 2.0A, SMBIOS 2.3 Rear panel 1 x PS/2 keyboard port 1 x PS/2 mouse port 2 x USB 2.
xii
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® P 5 C R - L ( S ) m o t h e r b o a r d ! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel® Pentium® 4 processor in the 775-land package. The motherboard supports the Intel® Pentium® 4 processor with 800/533 MHz Front Side Bus (FSB). The motherboard also supports the Intel® Hyper-Threading technology, is fully compatible with Intel® 04B and 04A processors, and incorporates the Extended Memory 64-bit Technology (EM64T).
PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to-point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI or PCI-X specifications. See page 2-18 for details.
1.3.2 Innovative ASUS features ASUS Smart Fan technology The ASUS Smart Fan technology smartly adjusts the fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See page 4-32 for details. CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted. This protection eliminates the need to buy a replacement ROM chip. See page 4-6 for details.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-6 2.4 System memory ................................................................. 2-13 2.5 Expansion slots ................................................................... 2-16 2.6 Jumpers ........................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Refer to the chassis documentation before installing the motherboard. Make sure to unplug the chassis power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.
2.2.3 Motherboard layout 25cm (9.8in) REAR_FAN1 PS/2KBMS T: Mouse B: Keyboard PSUSMB1 KBPWR1 ATXPWR1 FM_CPU2 CPU_FAN2 DDR2 DIMM_B2 (64 bit,240-pin module) ATX12V1 USBPW12 DDR2 DIMM_B1 (64 bit,240-pin module) USB12 FRNT_FAN1 REAR_FAN2 COM1 DDR2 DIMM_A2 (64 bit,240-pin module) LGA775 VGA1 P5CR-LS ® PARALLEL PORT DDR2 DIMM_A1 (64 bit,240-pin module) ® Intel E7221 30.
2.2.4 2-4 Layout contents Slots Page 1. CPU sockets 2-6 2. DDR2 DIMM sockets 2-13 3. PCI/PCI-X/PCI Express slots 2-18 Jumpers Page 1. Clear RTC RAM (CLRTC1) 2-19 2. CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) 2-20 3. USB device wake-up (3-pin USBPW12, USBPW34) 2-20 4. Keyboard power (3-pin KBPWR1) 2-21 5. Gigabit LAN controller setting (3-pin LAN_EN1) 2-21 6. Gigabit LAN controller setting (3-pin LAN_EN2) 2-22 7.
Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY1) 2-26 2. IDE connector (40-1 pin PRI_IDE1)) 2-27 3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) 2-28 4. Ultra320 SCSI connector (68-pin SCSIA1)[for P5CR-LS only] 2-29 5. CPU fan connectors (4-pin CPU_FAN1/CPU_FAN2)) 2-30 6. System fan connectors (3-pin REAR_FAN1/REAR_FAN2, FRNT_FAN1/FRNT_FAN2) 2-30 7. Hard disk activity LED connector (4-pin HDLED1) 2-31 8. USB connector (10-1 pin USB34) 2-31 9.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package. 2.3.1 • Your boxed Intel® Pentium® 4 LGA775 processor package should come with installation instructions for the CPU and heatsink. If the instructions in this section do not match the CPU documentation, follow the latter. • Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab A PnP cap Load lever B This side of the socket box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4.
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! Notes on Intel® Hyper-Threading Technology • This motherboard supports Intel® Pentium® 4 CPUs in the 775-land package with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® XP/2003 Server and Linux 2.4.
2.3.2 Installing the CPU heatsink and fan The Intel® Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel® Pentium® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®-certified multi-directional heatsink and fan.
2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. B A A B 3. A B B A Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1/CPU_FAN2. CPU_FAN2 CPU_FAN2 CPU_FAN1 GND FANPWR2 CPU_FAN1 FANOUT4 ® P5CR-LS FANOUT4 FANPWR2 GND P5CR-L(S) CPU fan connectors 2-10 • Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
4. Carefully remove the heatsink and fan assembly from the motherboard. 5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched to match the break on the socket and ensure correct installation.
Recommended memory configurations Sockets Mode Single-channel Dual-channel* DIMM_A1 (black) DIMM_A2 (blue) DIMM_B1 (black) DIMM_B2 (blue) — — — (1) Installed (2) — Installed — — (3) — — Installed — (4) — — — Installed — Installed — Installed — Installed Installed Installed Installed (1) Installed (2) — (3) Installed * Use only identical DDR2 DIMM pairs.
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards, and other cards that comply with PCI Express 1.0 specifications. The figure shows a network card installed on the PCI Express x1 slot. 2.5.5 PCI/PCI-X slots The PCI/PCI-X slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI 2.3 and PCI-X 1.0 specifications. The figure shows a LAN card installed on a PCI slot.
2.6 1. Jumpers Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) These jumpers allow you to connect either a 3-pin or a 4-pin fan cable plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set these jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to pins 2-3 if you are using a 4-pin plug. ® P5CR-LS FM_CPU2 2 1 3-pin fan 3 2 4-pin fan (Default) FM_CPU1 1 2 2 3 3-pin fan 4-pin fan (Default) P5CR-L(S) FM CPU Setting 3.
4. Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS.
6. Gigabit LAN controller setting (3-pin LAN_EN2) ® P5CR-LS These jumpers allow you to enable or disable the onboard Broadcom BCM5705E Gigabit LAN controller. Set to pins 1-2 to activate the Gigabit LAN feature. LAN_EN2 P5CR-L(S) LAN_EN2 setting 3 2 Disable ® SCSI controller setting (3-pin SCSI_EN1) [for P5CR-LS only] These jumpers allow you to enable or disable the onboard Adaptec AIC-7901 PCI-X U320 SCSI controller. Set to pins 1-2 to activate the SCSI feature, and support RAID configurations.
8. VGA graphics controller setting (3-pin VGA_EN1) ® P5CR-LS These jumpers allow you to enable or disable the onboard ATI Rage XL video graphics controller. Set to pins 1-2 to enable the video graphics controller.
9. BIOS recovery (3-pin RECOVERY1) This jumper allows you to recover your original BIOS from a floppy disk in case the BIOS codes and data are corrupted. To recover the BIOS: Turn OFF your computer and unplug the power cord. 2. Move the jumper cap from pins 1-2 (default) to pins 2-3. 3. Insert a floppy disk with the original or updated BIOS file. 4. Plug the power cord and turn ON the computer. 5. The system searches for the BIOS file in the floppy then reflashes the BIOS. 6.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 4 3 1. 2. 5 6 7 8 P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse. P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. P S / 2 k e y b o a r d p o r t ( p u r p l e ) . This port is for a PS/2 keyboard. 3. 4. U S B 2 . 0 p o r t s 1 a n d 2 . These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. S e r i a l ( C O M 1 ) p o r tt.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. ® P5CR-LS Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. FLOPPY1 PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
2. IDE connector (40-1 pin PRI_IDE1) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive).
3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0 or RAID 1 configuration with the onboard Intel® ICH6R RAID controller. These connectors are set to S t a n d a r d I D E mode by default. In S t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk drives to these connectors.
4. Ultra320 SCSI connector (68-pin SCSIA1) [for P5CR-LS only] This motherboard comes with the Adaptec® AIC7901 SCSI U320 controller that supports a 68-pin Ultra320 SCSI connector, which can support a maximum of 15 devices as specified by Ultra320 standards. SCSIA1 ® 1 35 P5CR-LS 68-Pin Ultra320/ Ultra2-Wide SCSI Connector 34 68 P5CR-L(S) Onboard SCSI connectors SCSI Connection Notes This motherboard has one optional 68-pin Ultra320 SCSI connector.
5. CPU and system fan connectors (4-pin CPU_FAN1/2, 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W max.) or a total of 2.1 A ~ 4.44 A (53.28 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
7. USB connector (10-1 pin USB34) USB+5V USB_P3USB_P3+ GND NC ® P5CR-LS This connector is for USB 2.0 ports. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. The USB connector complies with USB 2.0 specification that supports up to 480 Mbps connection speed. USB+5V USB_P2USB_P2+ GND USB34 P5CR-L(S) USB 2.0 connector Never connect a 1 3 9 4 c a b l e to the USB connectors.
9. S S I power connectors (24-pin ATXPWR1, 4 12V1) 4-- p i n A T X X1 These connectors are for SSI power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Use of an SSI 12 V Specification 2.0-compliant power supply unit (PSU) that provides a minimum power of 450 W is recommended for a fully-configured system.
1 0 . Backplane SMBus connector (6-1 pin BPSMB1) I2C_6_CLK# NC +5V I2C_6_DATA# GND ® P5CR-LS This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. 1 BPSMB1 P5CR-L(S) SMBus connector PSU_I2CCLK PSU_I2CDATA NC GND +3.3V Remote Sense ® P5CR-LS 1 1 . Power supply SMBus connector (6-1 pin PSUSMB1) This connector allows you to connect SMBus (System Management Bus) devices.
+5VSB +5VSB BMC SMBCLK 12CCLK1 PSON# BMC_RST# PWROK PSONEN# P5CR-LS ® 1 2 . BMC connector (16-pin BMCCONN1) This connector is for an ASUS server management card. +5VSB +5VSB BMC SMBDATA 12CDATA1 FP_PWRBTN# BMC_PRESENT# BMC_SMI# GND BMCCONN1 P5CR-L(S) BMC connector ® P5CR-LS 1 3 . Ambient thermal sensor connector (2-pin TRPWR1) If you want additional thermal monitoring, connect the thermal sensor cable with a thermistor (of 1ºK or at 25ºC, B=3435) to this connector.
1 4 . Auxiliary panel connector (20-pin AUX_PANEL1) GND I2C_4_DATA# +5VSB LAN1_LINKACTLED+ LAN1_LINKACTLEDLAN2_LINKACTLEDLAN2_LINKACTLED+ NC I2C_4_CLK# ® P5CR-LS This connector supports several server system functions. P5CR-L(S) Auxiliary panel connector • • • • • • • CASEOPEN GND LOCATORLED1+ LOCATORLED1LOCATORBTN# GND LOCATORLED2LOCATORLED2+ PIN1 +5VSB AUX_PANEL1 Chassis Intrusion connector (3-pin CASEOPEN) This lead is for a chassis with an intrusion detection feature.
1 5 . System panel connector (20-pin PANEL1) POWERLED+ GND POWERLEDMLED+ MLEDNC +5V GND GND SPKROUT ® P5CR-LS This connector supports several chassis-mounted functions. P5CR-L(S) System panel connector NMIBTN# GND POWERBTN# GND NC RESETBTN# GND HDLED+ HDLED- PANEL1 The sytem panel connector is color-coded for easy connection. • System power LED (Green 3-pin POWERLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer ..................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® Server 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® Server 2003: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS ........................................ 4-1 4.2 BIOS setup program ........................................................... 4-11 4.3 Main menu .......................................................................... 4-14 4.4 Advanced menu .................................................................. 4-19 4.5 Power menu ........................................................................ 4-29 4.6 Boot menu .....................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. 2. ASUS floppy ASUS A F U D O S (Updates the BIOS in DOS mode using a bootable disk.) E Z F l a s h (Updates the BIOS using a floppy disk during POST.) 3. A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) 4.
Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive. b. Insert the Windows® 2000 CD to the optical drive. c. Click S t a r tt, then select R u n n. d. In the O p e n field, type D:\bootdisk\makeboot a: assuming that D is your optical drive letter. e. Press , then follow screen instructions to continue. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 4.1.
EZFlash starting BIOS update Checking for floppy... Floppy found! Reading file “P5CRLS.ROM”. Completed. Start erasing.......| Start programming...| Flashed successfully. Rebooting. 4.1.3 • Do not shut down or reset the system while updating the BIOS to prevent system boot failure! • A “Floppy not found!” error message appears if there is no floppy disk in the drive. A “P5CRLS.ROM not found!” error message appears if the correct BIOS file is not found in the floppy disk.
3. Press . The utility copies the current BIOS file to the floppy disk. A:\>afudos /oOLDBIOS1.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done Write to file...... ok A:\> The utility returns to the DOS prompt after copying the current BIOS file. Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.
4. The utility verifies the file and starts updating the BIOS. A:\>afudos /iP5CRLS.ROM /pbnc AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... 0x0008CC00 (9%) Do not shut down or reset the system while updating the BIOS to prevent system boot failure! 5.
4.1.4 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 2. Insert the support CD to the optical drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
4.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Download the latest BIOS file from the Internet • Update the BIOS from an updated BIOS file • Update the BIOS directly from the Internet, and • View the BIOS version information. This utility is available in the support CD that comes with the motherboard package.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate e. The ASUS Update main window appears. 2. Select U p d a t e B I O S f r o m t h e I n t e r n e t option from the drop-down menu, then click N e x tt. ASUS P5CR-L(S) 3. Select the ASUS FTP site nearest you to avoid network traffic, or click A u t o S e l e c tt. Click N e x tt.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail of all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2.
4.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Menu bar Configuration fields System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration : : : : : General help [16:37:21] [Mon,10/02/2004] [1.44M, 3.5 in.] [English] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting M a i n shows the Main menu items. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [16:37:21] [Mon, 10/02/2004] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration : : : : : : [16:37:21] [Mon,10/02/2004] [1.44M, 3.5 in.
4.3.4 Primary, Third, and Fourth IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information. Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA SMART Monitoring : : : : : : : : : Hard Disk ST320410A 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
Enhanced Mode Support On [S-ATA] The default setting SATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports o n l y i f you did not install any Serial ATA device. The S-ATA+P-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting S A T A A.
4.3.6 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version : 08.00.10 Build Date : 01/17/05 Processor Type Speed Count : Genuine Intel(R) CPU 3.20 GHz : 3200 MHz : 1 System Memory Size : 512 MB AMI BIOS Displays the auto-detected BIOS information. Processor Displays the auto-detected CPU specification. System Memory Displays the auto-detected system memory.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Adjust system frequency/voltage USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP Remote Access Configuration 4.4.1 USB Configuration The items in this menu allow you to change the USB-related features.
USB Function [Enabled] Allows you to enable or disable the USB function. Configuration options: [Disabled] [Enabled] Legacy USB Support [Auto] Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] USB 2.
4.4.2 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure advanced CPU Settings Manufacturer : Intel Brand String : Genuine Intel (R) CPU 3.
Max CPUID Value Limit [Disabled] Enable this item to boot legacy operating systems that cannot support CPUs with extended CPUID functions. Configuration options: [Disabled] [Enabled] Execute Disable Bit [Disabled] When this item is set to [Disabled], the BIOS forces the XD feature flag to always return to (0). Configuration options: [Disabled] [Enabled] Enhanced C1 Control [Auto] When set to [Auto], the BIOS will automatically check the CPU’s capability to enable the C1E support.
4.4.3 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu. Advanced Chipset Settings Configure DRAM Timing by SPD DRAM ECC Mode Hyper Path 2 [Enabled] [Auto] [Auto] Onboard SCSI Boot ROM Onboard LAN Boot ROM [Enabled] [Enabled] Enable or disable DRAM timing.
DRAM ECC Mode [Auto] Allows you to enable or disable DRAM timing. Configuration options: [Auto] [Disabled] Hyper Path 2 [Auto] Allows you to enable or disable the ASUS Hyper Path 2 feature. Configuration options: [Disabled] [Enabled] [Auto] Onboard SCSI Boot ROM [Enabled] (This item is for model P5CR-LS only) Allows you to enable or disable the onboard SCSI boot ROM. Configuration options: [Disabled] [Enabled] Onboard LAN Boot ROM [Enabled] Allows you to enable or disable the onboard LAN boot ROM.
4.4.4 Onboard Devices Configuration Configure Win627EHF Super IO Chipset Serial Port1 Address Serial Port2 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ [3F8/IRQ4] [2F8/IRQ3] [378] [ECP] [DMA3] [IRQ7] Enable or disable the Azalia controller. Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address.
4.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested. Configuration options: [Yes] [No] Palette Snooping [Disabled] When set to [Enabled], the palette snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly.
Remote Access [Disabled] Enables or disables the remote access feature. Configuration options: [Disabled] [Enabled] The succeeding items appear when the item R e m o t e A c c e s s is set to [Enabled]. Serial port number [COM1] Sets the serial port for console redirection. Make sure the selected port is enabled. Configuration options: [COM1] [COM2] Serial Port Mode [115200, 8,n,1] Allows you to select the serial port mode settings.
4.5 Power menu The Power menu items allow you to change the settings for the ACPI and Advanced Power Management (APM). Select an item then press to display the configuration options. ACPI APIC Support [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 4.5.1 ACPI APIC Support [Enabled] Allows you to enable or disable the Advanced Configuration and Power Interface (ACPI) support in the Application-Specific Integrated Circuit (ASIC).
4.5.2 APM Configuration APM Configuration Power Button Mode Go into On/Off or Suspend when Power button is pressed. [On/Off] Restore on AC Power Loss [Power Off] Power On By RTC Alarm [Disabled] Power On By External Modems [Disabled] Power On By PCI Devices [Disabled] Power On By PS/2 Keyboard [Disabled] Keyboard Wakeup Password : Not Installed Power On By PS/2 Mouse [Disabled] Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed.
Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] Keyboard Wakeup Password This item appears only when the Power On By PS/2 Keyboard is set to Enabled. Select this item to set or change the keyboard wakeup password.
CPU Fan 1/2 Speed [xxxxRPM] or [N/A] Front1/Front2 Fan Speed [xxxxRPM] or [N/A] Rear1/Rear2 Fan Speed [xxxxRPM] or [N/A] The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Smart Fan Control [Enabled] Allows you to enable or disable the ASUS Smart Fan feature that smartly adjusts the fan speeds for more efficient system operation.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Boot Settings Specifies the Boot Device Boot Priority sequence. Boot Device Priority Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.6.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [On] [Auto] [Enabled] [Enabled] [Enabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Hit ‘DEL’ Message Display [Enabled] When set to Enabled, the system displays the message “Press DEL to run Setup” during POST. Configuration options: [Disabled] [Enabled] Interrupt 19 Capture [Enabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options.
If you forget your BIOS password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section “2.6 Jumpers” for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check to change password.
The message “Password Installed” appears after you set your password successfully. To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] 4.
Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select Y e s to save changes and exit.
This chapter provides information on RAID configurations, RAID driver installation, and LAN driver installation for this motherboard.
Chapter summary 5 5.1 RAID configurations .............................................................. 5-1 5.2 RAID driver installation ......................................................... 5-8 5.3. LAN driver installation ........................................................ 5-14 5.4 VGA driver installation ........................................................
5.1 RAID configurations The server system/motherboard comes with the I n t e l® I C H 6 R Southbridge chip that supports up to four Serial ATA hard disk drives with RAID 0, RAID 1, or Intel ® Matrix Storage configuration. Refer to the RAID definitions below. 5.1.1 RAID definitions R A I D 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
5.1.2 Installing hard disk drives The motherboard supports Serial ATA hard disk drives for RAID set configuration. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for RAID configuration: 1. Install the SATA hard disks into the drive bays following the instructions in the system user guide. 2. Connect a SATA signal cable to the signal connector at the back of each drive and to the SATA connector on the motherboard.
5.1.5 Intel® Application Accelerator RAID Option ROM Utility The Intel® Application Accelerator RAID Option ROM utility allows you to create RAID 0 and RAID 1 set(s) from SATA hard disk drives that are connected to the SATA connectors supported by the motherboard Southbridge chip. To enter the Intel® Application Accelerator RAID Option ROM utility: 1. Turn on the system after installing all the SATA hard disk drives. 2. During POST, press to display the utility main menu.
Creating a RAID 0 set (striped) To create a RAID 0 set: 1. From the utility main menu, select [ 1 . C r e a t e R A I D V o l u m e ]], then press . The following screen appears. Intel(R) Application Accelerator RAID Option ROM v4.0.0.6211 Copyright(C) 2003-04 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: RAID_Volume1 RAID0(Stripe) Select Disk 128KB 149.
Creating a RAID 1 set (mirrored) To create a RAID 1 set: 1. From the utility main menu, select [ 1 . C r e a t e R A I D V o l u m e ]], then press . The following screen appears. Intel(R) Application Accelerator RAID Option ROM v4.0.0.6211 Copyright(C) 2003-04 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: RAID_Volume1 RAID1(Mirror) Select Disk 128KB 149.
Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select [ 2 . D e l e t e R A I D V o l u m e ]], then press to display the following screen. Intel(R) Application Accelerator RAID Option ROM v4.0.0.6211 Copyright(C) 2003-04 Intel Corporation. All Rights Reserved. [ DELETE ARRAY MENU ] Name RAID_Volume1 Level Drives RAID0(Stripe) 2 Capacity Status 149.
Resetting a RAID set hard disks drive Take caution before you reset a RAID volume HDD to non-RAID. Resetting a RAID volume HDD deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select [ 3 . R e s e t D i s k s t o N o n - R A I D ]], then press to display the following screen. [ RESET RAID DATA ] Resetting RAID data will remove the internal RAID structures from the selected RAID disks.
5.2 RAID driver installation 5.2.1 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. You can create a RAID driver disk in DOS (using FreeDOS from the support CD) or in Windows® environment. DOS To create a RAID driver disk in DOS environment: 1. Place the motherboard support CD in the optical drive. 2. Restart the computer, then enter the BIOS Setup. 3.
Windows® 2000/2003 Server To create a RAID driver disk in Windows® 2000/2003 Server environment: 1. Restart the system from the hard disk drive, then place the system/ motherboard support CD in the optical drive. 2. Browse the contents of the support CD to locate the driver disk utility. The RAID driver disk for the Intel® ICH6R is located in: \Drivers\Chipset\Intel\IAA\F6 Install Floppy\F6flpy32 3. Insert a formatted high-density floppy disk to the floppy disk drive. 4.
5 ..2.2 2.2 Installing the Intel® ICH6R RAID controller driver Windows® 2000/2003 Server OS During Windows® 2000/2003 Server OS installation To install the Intel® ICH6R RAID controller driver when installing Windows® 2000/2003 Server OS: 1. Boot the computer using the Windows® 2000/2003 Server installation CD. The W i n d o w s® 2 0 0 0 / 2 0 0 3 S e t u p starts. 2. Press F6 if you need to install Press when the message “P a t h i r d p a r t y S C S I o r R A I D d r i v e r . . ..
4. Insert the Intel® ICH6R RAID driver disk you created earlier to the floppy disk drive, then press . 5. Select the I n t e l ( R ) 8 2 8 0 1 F R S A T A R A I D C o n t r o l l e r ( D e s k t o p I C H 6 R ) from the options, then press to select. 6. The Windows® 2000/2003 Setup loads the RAID controller drivers from the RAID driver disk. When prompted, press to continue installation. 7. Setup then proceeds with the OS installation. Follow screen instructions to continue.
To an existing Windows® 2000/2003 Server OS To install the Intel® ICH6R RAID controller driver on an existing Windows® 2000/2003 Server OS: 1. Restart the computer, then log on with A d m i n i s t r a t o r privileges. 2. Windows® automatically detects the RAID controller and displays a N e w H a r d w a r e F o u n d window. Click C a n c e ll. Right-click the M y C o m p u t e r icon on the Windows® desktop , then select P r o p e r t i e s from the menu. 3. 4.
11. Click F i n i s h after the driver installation is done. To verify the Intel® ICH6R RAID controller driver installation: 1. 2. 3. Right-click the M y C o m p u t e r icon on the Windows® desktop , then select P r o p e r t i e s from the menu. Click the H a r d w a r e tab, then click the D e v i c e M a n a g e r button. Click the “+” sign before the item I D E A T A / A T A P I c o n t r o l l e r ss.
5.3. LAN driver installation This section provides instructions on how to install the Broadcom® Gigabit LAN controller drivers. 5.3.1 Windows® 2000/2003 Server To install the Broadcom® Gigabit LAN controller driver on a Windows® 2000/2003 Server OS: 1. Restart the computer, then log on with A d m i n i s t r a t o r privileges. 2. Insert the motherboard/system support CD to the optical drive. The CD automatically displays the D r i v e r s menu if Autorun is enabled in your computer. 3.
4. Click N e x t when the InstallShield Wizard window appears. Follow screen instructions to continue installation.
5.3.2 Windows® N T • You must install a network device driver before you can use the LAN adapter on a Windows® NT system. • You must upgrade the system to Windows® NT Service Pack 4 or later before you install the LAN adapter drivers. • BACS2 Help files require Internet Explorer 4.0 or later to work properly. We recommend using Internet Explorer 5.0 to view help files. To install the Broadcom® Gigabit LAN controller driver on a Windows® NT OS: 1. 2. 3. 4. 5. 6. 7. 8.
5.3.3 Red Hat® Linux 9.0 Follow these instructions when installing the Broadcom® Gigabit LAN controller base driver for the Red Hat® Linux version 5.2.x operating system. The following procedures were tested for 2.4.x kernels through 2.4.20. Installing the source RPM package To install the source RPM package: 1. Install the source RPM package: rpm -ivh bcm5700-.src.rpm 2.
Building the driver from the TAR file To build the driver from the TAR file: 1. Create a directory and extract the TAR files: tar xvzf bcm5700-.tar.gz 2. Build the driver bcm5700.o as a loadable module for the running kernel: cd bcm5700-/src make 3. Test the driver by loading it: insmod bcm5700.o 4. Install the driver and man page: make install See the RPM instructions on the previous page for the location of the installed driver. 5.
5.4 VGA driver installation This section provides instructions on how to install the Intel® E7221 Super Video Graphics Adapter (SVGA) driver. 5.4.1 Windows® 2000 Server You need to manually install the Intel® E7221 SVGA driver on a Windows® 2000 Server operating system. To install the Intel® E7221 SVGA driver: 1. Restart the computer, then log on with A d m i n i s t r a t o r privileges. 2. Insert the motherboard/system support CD to the optical drive.
5.4.2 Windows® 2003 Server The Windows® 2003 Server operating system automatically recognizes the Intel® E7221 SVGA driver during system installation. There is no need to install an additional driver(s) to support the onboard VGA. Verifying the VGA driver installation To verify if the Intel® E7221 SVGA driver is properly installed in a Windows® 2000/2003 Server operating system: 1. 2. 3. Right-click the M y C o m p u t e r icon on the Windows® desktop, then select P r o p e r t i e s from the menu.
5.4.3 Red Hat® Linux 9.0 The Red Hat® Linux 9.0 (2.4.x kernels) operating system automatically recognizes the Intel® E7221 SVGA driver during system installation. There is no need to install an additional driver(s) to support the onboard VGA.
5-22 Chapter 5: D Drr i v e r i n s t a l l a t i o n
The appendix includes additional information that you may refer to when configuring the motherboard.
Appendix summary A.1 A P5CR-L(S) block diagram .....................................................
A.1 P5CR-L(S) block diagram ® ® Intel Pentium 4 Processor in the 775-land package with 800 MHz system bus System Bus 64bit, 800 MHz 4xDDR2 400/533 DIMM slots (max. 4 GB) PCI Slot 1 PCI-E interfaces PCI-X 133 MHz bus* X8 PCI-E Adaptec AIC-7901 U320 SCSI (optional) Intel 6702PXH PCI Slot 2 Four DDR2 400/533 DIMM Sockets Northbridge Intel® E7221 Southbridge Intel ® ICH6R ATI Rage XL 8 Mbyte PCI Slot 3 PCI 33 bus PCI Slot 4 DMI interface PCI Slot 5 VGA-Conn.
A-2 Appendix A: Reference information
