Intel® NUC 12 Pro Kit NUC12WSHi3 Intel® NUC 12 Pro Kit NUC12WSHi30L Intel® NUC 12 Pro Kit NUC12WSHi30Z Intel® NUC 12 Pro Kit NUC12WSHi5 Intel® NUC 12 Pro Kit NUC12WSHi50Z Intel® NUC 12 Pro Kit NUC12WSHv5 Intel® NUC 12 Pro Kit NUC12WSHv50L Intel® NUC 12 Pro Kit NUC12WSHv50Z Intel® NUC 12 Pro Kit NUC12WSHi7 Intel® NUC 12 Pro Kit NUC12WSHi70Z Intel® NUC 12 Pro Kit NUC12WSHv7 Intel® NUC 12 Pro Kit NUC12WSHv70L Intel® NUC 12 Pro Kit NUC12WSHv70Z User Guide August 2022 1 NUC12WSH User Guide – August 2022
You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject matter disclosed herein. No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document. All information provided here is subject to change without notice.
Contents 1.0 Introduction ....................................................................................................................................................... 5 1.1 1.2 1.3 Before You Begin ........................................................................................................................................... 5 Installation Precautions .............................................................................................................................
Revision History Date Revision August 2022 1.0 Description Initial release.
1.0 Introduction This User Guide provides step-by-step installation instructions for these products: • • • • • • • • • • • • • 1.
procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station isn’t available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis. 1.2 Installation Precautions When you install and test the Intel NUC, observe all warnings and cautions in the installation instructions.
2.0 Open the Chassis Unscrew the four corner screws on the bottom of the chassis and lift the cover.
3.0 Install and Remove System Memory Intel® NUC 12 Pro Kit NUC12WSH has two 260-pin DDR4 SO-DIMM memory slots Memory requirements: • • • 1.2V low voltage memory 2133/2400/3200 MHz SO-DIMMs Non-ECC Find compatible system memory modules at the Intel® Product Compatibility Tool: • • • • • • • • • • • • • 3.
3. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket. 4. Insert the bottom edge of the SO-DIMM into the socket. 5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 3.2 Remove SO-DIMMs To remove a SO-DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" in Section 1.1. 2. Turn off all peripheral devices connected to the computer.
4.0 Install an M.2 SSD Intel® NUC 12 Pro Kit NUC12WSH supports 80mm and 42mm SSDs. Find compatible M.
If you’re installing a 42mm M.2 SSD: 1. Remove the small silver screw from the metal standoff on the motherboard (A). 2. Move the standoff (B) from the 80mm position to the 42mm position (C). 3. Align the small notch at the bottom edge of the M.2 card with the key in the connector. 4. Insert the bottom edge of the M.2 card into the connector (D). 5. Secure the card to the standoff with the small silver screw (E).
5.0 Install a 2.5-inch SSD or Hard Drive Intel® NUC 12 Pro Kit NUC12WSH supports an additional 2.5” Solid State Drive (SSD) or Hard Disk Drive (HDD). Find compatible 2.
2. Secure the drive into the drive bay with the two small silver screws that were included in the box. Set the drive bay bracket down inside the chassis.
6.0 Close the Chassis After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.
7.0 Use the VESA Bracket (Optional) Follow these instructions to attach and use the VESA mount bracket: 1. Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV. 2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
3. Slide the Intel NUC onto the VESA mount bracket.
8.0 Connect Power Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the power adapter). Product codes Power cord type RNUC12WSHi30000 RNUC12WSHi30L00 RNUC12WSHi30Z00 RNUC12WSHi50000 RNUC12WSHi50Z00 RNUC12WSHv50000 RNUC12WSHv50L00 RNUC12WSHv50Z00 RNUC12WSHi70000 RNUC12WSHi70Z00 RNUC12WSHv70000 RNUC12WSHv70L00 RNUC12WSHv70Z00 No power cord included. An AC power cord needs to be purchased separately.
RNUC12WSHi70006 RNUC12WSHi70Z06 18 NUC12WSH User Guide – August 2022
9.0 Install an Operating System See Supported Operating Systems for a list of Intel-validated Windows* operating systems. The Intel Product Compatibility Tool lists versions of Linux* that have been reported as compatible by Intel NUC owners. If you need assistance with Linux on your Intel NUC, check the distribution’s website and forums for peer assistance. Refer to Operating System Installation for system requirements and installation steps.
10.
