MCI-1G/350-2T MCI-1G/350-4T 1 Gigabit/s Ethernet card User Guide
E13848 First Edition March 2018 Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this guide.......................................................................................................... iv How this guide is organized.............................................................................iv Where to find more information........................................................................iv Conventions used in this guide........................................................................ v Typography..................................................
About this guide This user guide contains the information you need when installing and configuring the server management board. How this guide is organized This guide contains the following parts: • Chapter 1: Product Introduction This chapter describes the MCI-1G/350 series Ethernet card features and the new technologies it supports. • Chapter 2: Boot Agent Configuration This chapter provides instructions on setting the Intel(R) Boot Agent XE.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
MCI-1G/350 series specifications summary Model Name MCI-1G/350-2T MCI-1G/350-4T Data Rate Per Port 10/100/1000 Mbps 10/100/1000 Mbps Ports 2 ports 4 ports Controller Intel I350-AM2 Intel I350-AM4 Connector RJ45 Host Interface PCIe 2.
Chapter 1: Product Introduction Product Introduction This chapter offers the MCI-1G/350 series Ethernet card features and the new technologies it supports.
1.1 Welcome! Thank you for buying an ASUS® MCI-1G/350 series 1 Gigabit/s Ethernet card! Before you start installing the Ethernet card, check the items in your package with the list below. 1.2 Package contents Check your package for the following items. Standard Gift Box Pack ASUS MCI-1G/350 series Ethernet card 1 LED Signal Cable 1 Packing Quantity 1 pc per carton If any of the above items are damaged or missing, contact your retailer. 1.
1.4 Card layout Front view MCI-1G/350-2T MCI-1G/350-4T 1. AUXLED_CON1 connector 4. Connector A (PCIe 2.0 x4 Link) 2. LAN port 1 5. LAN port 3 3. LAN port 2 6.
1.
1.6 Installing the MCI-1G/350 series Ethernet card To install a MCI-1G/350 series Ethernet card: 1. Prepare the Mezzanine card. 2. Connect the black end of the signal cable to the OCP_LED1 header on the motherboard. Signal cable OCP_LED1 3. Connect the white end of the signal cable to the AUXLED_CON1 connector on the card.
1-6 4. Align and insert the screw holes of the MCI-1G/350 series Ethernet card into the stand screws, then insert the ports of the MCI-1G/350 series Ethernet card into the port slots on the server chassis as shown. 5. Secure the MCI-1G/350 series Ethernet card with the four (4) bundled screws.
Chapter 2: Boot Agent Configuration Boot Agent Configuration This chapter provides instructions on setting the Intel(R) Boot Agent XE.
2.1 Intel(R) iSCSI Remote Boot The Intel(R) iSCSI Remote Boot provides hardware-based Ethernet card configurations. To start the Intel(R) iSCSI Remote Boot and access the main screen: 1. Turn on the system. 2. During POST, press when the following screen appears. Intel(R) iSCSI Remote Boot version 3.0.84 Copyright(c) 2003-2014 Intel Corporation. All rights reserved. Press ESC key to skip iSCSI boot initialization. Press to run setup... 3.
2.1.1 iSCSI Boot Configuration Intel(R) iSCSI Remote Boot v3.0.84 iSCSI Boot Configuration [ ] Use dynamic IP configuration (DHCP) ________________ Initiator Name: 0.0.0.0_________ Initiator IP: 0.0.0.0_________ Subnet Mask: 0.0.0.0_________ Gateway: VLAN ID: [ ] Use DHCP for iSCSI Target information ________________ Target Name: 0.0.0.0_________ Target IP: 0.0.0.0_________ Target Port: 0.0.0.0_________ Boot LUN: Press spacebar to change [OK] [Cancel] Copyright(c) 2003-2014 Intel Corporation.
2.1.2 iSCSI CHAP Configuration Intel(R) iSCSI Remote Boot v3.0.84 iSCSI CHAP Configuration Specify the same authentication information as configured on the target. [ ] Use CHAP User Name: Target Secret: [ ] Use Mutual CHAP Initiator Secret: Minimum CHAP secret length is 12 and maximum 16. [OK] [Cancel] Copyright(c) 2003-2014 Intel Corporation. All rights reserved. Use the Up/Down arrow key to select an item and press to change between Enabled [*] or Disabled [ ].
2.2 Intel(R) Ethernet Flash Firmware Utility The Intel(R) Ethernet Flash Firmware Utility allows you to switch between PXE option ROM and iSCSI option ROM. Note that only one option ROM can be used at a time. To install the PXE option ROM: 1. Locate the BootIMG.FLB and Bootutil.exe files in the PXE folder on your SDVD. 2. Copy the BootIMG.FLB and Bootutil.exe files to a bootable USB storage device. 3. Enter DOS environment. The utility must run under pure DOS environment.
To install the iSCSI option ROM: 1. Locate the BootIMG.FLB and Bootutil.exe files in the iSCSI folder on your SDVD. 2. Copy the BootIMG.FLB and Bootutil.exe files to a bootable USB storage device. 3. Enter DOS environment. The utility must run under pure DOS environment. It cannot run in a DOS box on Windows system. You should boot from a DOS floppy without any device drivers. 4. Within the DOS environment, enter the directory with the BootIMG.FLB and Bootutil. exe files. 5.
Chapter 3: Driver Installation Driver Installation This chapter provides instructions for installing the Ethernet card drivers on different operating systems.
3.1 Windows® Server OS Driver Installation To update the Ethernet card driver for Windows® Server OS: 3-2 1. Restart the computer, and then log on with Administrator privileges. 2. Insert the Support CD to the optical drive. The Support CD automatically displays the Drivers menu if Autorun is enabled in your computer. • If Windows® automatically detects the LAN controllers and displays a New Hardware Found window, click Cancel to close this window.
5. Follow the onscreen instructions to complete the installation.
3.2 Linux OS Driver Installation To install the Ethernet card driver for Linux OS: 1. Within the Linux Terminal, place the driver in root/tmp: For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.4: For SUSE Linux Enterprise Server 11.3: 2. Unzip the driver: tar zxf .tar.gz For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.4: For SUSE Linux Enterprise Server 11.
3. Enter the folder: cd /src For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.4: For SUSE Linux Enterprise Server 11.
4. Install the driver: make install For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.4: For SUSE Linux Enterprise Server 11.
5. Install complete: For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.4: For SUSE Linux Enterprise Server 11.
6. Check if the LAN card is detected: service network restart For Red Hat Enterprise Linux 6.9: For Red Hat Enterprise Linux 7.
For SUSE Linux Enterprise Server 11.
3-10 Chapter 3: Driver Installation
Appendix Appendix A
Simplified EU Declaration of Conformity English ASUSTeK Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of related Directives. Full text of EU declaration of conformity is available at: www.asus.com/support Français AsusTek Computer Inc. déclare par la présente que cet appareil est conforme aux critères essentiels et autres clauses pertinentes des directives concernées.
ASUS contact information ASUSTeK COMPUTER INC. (Taiwan) Address 4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan Telephone +886-2-2894-3447 Fax +886-2-2890-7798 Web site https://www.asus.com/tw/ Technical Support Telephone +886-2-2894-3447 (0800-093-456) Online Support https://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-tw ASUSTeK COMPUTER INC. (China) Address No.
A-4 Appendix
