Content English ..................................................................................................1 简体中文 ...............................................................................................8 Türkçe ................................................................................................
GigaX Series Layer 2 Unmanaged Switch GigaX1048 User Manual 1
Introduction Thank you for purchasing the GigaX1048 switch! The GigaX1048 switch is a multi-port switch designed for building a high-performance workgroup network. It features store-and-forward switching architecture which reduces transmission latency and therefore offers high-speed network exchange. With non-blocking and full wire-speed functions, you do not need to compete with other users for bandwidth.
Package contents Before you start installing the switch, check in your package for the following items: 1 x ASUS GigaX1048 switch 1 x Power cord 1 x User manual 1 x Rack-mount kit 4 x Rubber stands GigaX 1048 switch Rack-mount kit Rubber stands Power cord User manual Note: If any of the above items is damaged or missing, contact your retailer.
Hardware description This section introduces the physical features of the GigaX1048 switch and its installation procedure. Front panel The front panel of GigaX1048 switch features forty-eight RJ-45 10/100Mbps ports (auto MDI/ MDIX), one RJ-45 10/100/100Mbps port, one Mini GBIC slot for fiber connection, and LED indicators that indicate the condition of the switch. LED Indicators Figure 1. Front panel RJ-45 Ports (Auto MDI/MDIX): The forty-eight RJ-45 10/100Mbps ports are auto MDI/MDIX ready.
Rear panel The three-pronged power plug is located at the rear panel of the GigaX1048 switch. The input voltage is 100-240V AC with 50-60Hz frequency. The power plug includes a fuse (ø5mm x 20mm 2A/250V Max.) that prevents damage to the switch due to unstable voltage. The fuse could be replaced when busted. Fuse specification: Ceramic tube type ø5mm x 20mm 2A/250V (Max.) Figure 2. Rear Panel Desktop installation Attaching rubber stands 1. Place the switch on a stable and dust-free surface. 2.
Troubleshooting Problem Suggested action System LED does not light up after the switch is turned on. Verify if the power cord is securely connected to the switch and to a power strip. Link LED does not light up after an Ethernet cable is attached. 1. Look for loose or faulty connections, make sure the connections are secure. If these could not solve the problem, try another cable. 2. Check the network cable used.
Technical specifications This section provides the specifications of the GigaX1048 switch. Standard IEEE802.3 10BASE-T Ethernet IEEE802.3u 100BASE-TX Fast Ethernet IEEE802.3ab 1000BASE-T IEEE802.2x Flow Control and Back-pressure IEEE802.
GigaX 系列 两层非网管型交换机 GigaX1048 用户手册 8
产品简介 非常感谢您购买华硕的 GigaX1048 交换机!此 GigaX1048 交换机是一台具备组建高性能工作 组网络功能的多端口交换机。GigaX1048 采用可靠的存储转发的方式,减少潜在的不必要的数 据转发,从而有效改善网络性能。同时由于支持非阻塞(Non-blocking)和全线速(Full Wirespeed)功能,您不用再为拥挤的网络而心烦气躁,轻松即可获得满意的网络带宽。此交换机带 有 48 个 RJ-45 10/100Mbps 端口,一个 RJ-45 10/100/1000Mbps 端口和一个 Mini GBIC 端口。 GigaX1048 交换机绝对是中小型企业组建局域网和广域网的最佳选择。 产品特性 • 端口情况 : - 48 x RJ-45 10/100Mbps 端口 - 1 x RJ-45 10/100/1000Mbps 端口 - 1 x Mini GBIC 插槽 • 遵循 IEEE 802.3, 802.3u, 802.3ab 和 802.
产品包装 在您准备安装交换机以前,请仔细检查包装盒内是否装有以下标准配件: 1 x 华硕 GigaX1048 交换机 1 x 电源线 1 x 用户手册 1 x 机架配件 4 x 橡胶底垫 橡胶底垫 Rubber stands 华硕 GigaX1048 交换机 GigaX 1048 switch 机架配件 kit Rack-mount Power cord 电源线 用户手册 User manual 注意:若以上列出的任何一项配件有损坏或丢失的情况,请尽快与您的经销商联系。 10
硬件信息 本节将详细介绍 GigaX1048 交换机的产品特性和安装步骤。 前面板 GigaX1048 交换机的前面板带有 48 个 RJ-45 10/100Mbps 端口(自动 MDI/MDIX 功能),1 个 RJ-45 10/100/1000Mbps 端口,1 个用于光纤连接的 Mini GBIC 插槽和相对应的 LED 指示灯以 显示各端口连接的状况。 LED 指示灯 图 1.
后面板 GigaX1048 的后面板上有一个三叉头的电源插孔。输入电压要求是 50-60Hz 的 100-240V 直流 电源。插孔里有一个保险丝(最大 ø5mm x 20mm 2A/250V),能保护交换机不会因不稳定电压的 因素而损坏。当此保险丝坏掉后,请及时更换。 保险丝规格:陶瓷管状 ø5mm x 20mm 2A/250V(最大) 图 2. 后面板 桌面安装 安装橡胶底垫 1. 2. 3. 4. 将交换机放置在一个稳定的无尘的物体表面。 移除橡胶底垫的胶盖。 将橡胶底垫安在交换机底部的一个角落。 重复步骤 2 和 3,依次放置其他几个底垫。 机架安装 华硕 GigaX1048 交换机配带有适用于 EIA 标准 19 英寸机架的安装配件。请按照以下安装步骤 将交换机安装在机架上: 1. 使用小螺丝通过交换机两边的孔将支架固定。 2. 将华硕 GigaX1048 交换机放在机架上。确认支架上的小孔与机架上的孔相对应,然后拧紧 螺丝。 注意:针对封闭的机架空间,为了保证一定的通风,交换机的前面至少要有 4 英寸(10 cm)的 空间,背面至少要有 3.
疑问解决 问题 相关建议 交换机打开以后,系统 LED 指示灯仍旧不亮。 请检查电源线是否正确的连接至交换机和电源插座。 以太网线连接以后,Link LED 指示灯仍旧不亮。 1. 您需要检查连接是否松动或有误,要确保连接必须是通畅 完好的。如果问题仍不能解决,请换一根网线试试。 2. 检查正使用的网线。不标准的、有问题的网线会引起网络 冲突,从而严重影响网络性能。请使用 CAT5 网线测试器 测试一下。 3.
技术规格 下表详细列出了 GigaX1048 交换机的规格: 14 标准 IEEE802.3 10BASE-T Ethernet IEEE802.3u 100BASE-TX Fast Ethernet IEEE802.3ab 1000BASE-T IEEE802.2x Flow Control and Back-pressure IEEE802.
GigaX Serisi 2 Katman Yönetilmeyen Anahtar GigaX1048 Kullanıcı El Kitabı 15
Giriş GigaX1048 anahtarını satın aldığınız için teşekkür ederiz! GigaX1048 anahtarı yüksek performansa sahip çalışma grubu ağı oluşturmak için tasarlanan çoklu porta sahip bir anahtardır. Sakla ve ilet anahtarlama mimarisine sahiptir ve bu da aktarım gecikme süresini azaltır ve dolayısıyla yüksek hızda ağ değiştirme özelliği sunar. Bloke edilemeyen ve tam kablo hızlı işlevleri sayesinde diğer kullanıcılar ile geniş bant için yarışmanıza gerek yoktur.
Paket muhteviyatı Anahtarı kurmaya başlamadan önce, aşağıdakilerin paketinizde olduğunu kontrol ediniz: 1 x ASUS GigaX1048 anahtarı 1 x Güç kablosu 1 x Kullanım el kitabı 1 x Rafa monte etme kiti 4 x Plastik standlar GigaX 1048 switch Rack-mount kit Rubber stands Power cord User manual Not: Yukarıda belirtilenlerden herhangi biri yoksa veya hasar görmüşse, bayiiniz ile temasa geçiniz.
Donanım tanımı Bu bölümde GigaX1048 anahtarının fiziksel özellikleri ve kurulum prosedürü anlatılmaktadır. Ön Panel GigaX1048 anahtarının ön paneli kırk sekiz RJ-45 10/100Mbps portuna (otomatik MDI/MDIX), bir RJ-45 10/100/100Mbps portuna, fiber bağlantı için bir Mini GBIC yuvasına ve anahtarın durumunu gösteren LED göstergelerine sahiptir. LED göstergeleri Şekil 1. Ön Panel RJ-45 Portları (Otomatik MDI/MDIX): Kırk sekiz RJ-45 10/100Mbps portu hazır otomatik MDI/MDIXʼdir.
Arka Panel Guc fisi GigaX1048 anahtarinin arkasina güç fişi GigaX1048 anahtarının arkasında yerleştirilmiştir. Giriş voltajı 50-60Hz frekansı ile 100-240V ACʼdir. Güç fişine sigorta (ø5mm x 20mm 2A/250V Maks.) dahil olup kararsız voltaj nedeniyle anahtara zarar vermesini önler. Sigorta patladığında değiştirilmelidir. Sigortanın özelliği: Seramik tüp türü ø5mm x 20mm2A/250V (Maks) Şekil 2. Arka Panel Masaüstüne Kurulum Plastik standların takılması 1.
Sorun Giderme Sorun Switch açıldıktan sonra SİSTEM LEDʼi yanmıyor. Önerilen İşlem Güç kablosunun switchʼe ve duvardaki prize/güç kayışına güvenilir bir şekilde bağlanıp bağlanmadığını doğrulayın. E t h e r n e t k a b l o s u 1. Gevşek veya arızalı bağlantıları inceleyin, bağlantıların sağlam takıldıktan sonra Bağlantı olduğundan emin olun. Bunlar sorunu çözemiyorsa, başka bir LEDʼi yanmıyor. kabloyu deneyin. 2. Kullanılan ağ kablosunu kontrol edin.
Teknik özellikler Bu bölümde GigaX1048 anahtarının özellikleri verilmiştir. Standart IEEE802.3 10BASE-T Ethernet IEEE802.3u 100BASE-TX Hızlı Ethernet IEEE802.3ab 1000BASE-T IEEE802.2x Akış Kontrolü ve Geri basınç IEEE802.