User Guide DSL-N12HP 300Mbps Wi-Fi ADSL Modem Router
E11002 First Edition October 2015 Copyright © 2015 ASUSTeK Computer Inc. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. (“ASUS”).
Table of contents 1 Getting to know your ADSL modem router 2 Getting started 3 Configuring the General settings 1.1 1.2 1.3 1.4 1.5 1.6 2.1 2.2 2.3 2.4 2.5 3.1 Welcome!.........................................................................................6 Package contents..........................................................................6 Your ADSL modem router..........................................................7 Positioning your ADSL modem router..................................
Table of contents 3.2.6 Parental Control .....................................................................55 3.2.7 Routing ....................................................................................58 3.3 Advanced Setup......................................................................... 63 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.7 3.4 Wireless.......................................................................................... 95 3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.4.6 3.4.
Table of contents Appendix A - Firewall Appendix B - Pin Assignments Appendix C – Specifications Appendix D - SSH Client Appendix E - Connection Setup E1 Layer 2 Interfaces.....................................................................132 E1.1 ATM Interfaces...................................................................... 132 E1.2 ETHERNET WAN Interfaces............................................... 135 E2 WAN Connections....................................................................
1 Getting to know your ADSL modem router 1.1 Welcome! Thank you for purchasing an ASUS DSL-N12HP Wi-Fi ADSL Modem Router! DSL-N12HP is an 802.11n (300Mbps) Wireless ADSL2+ router comprising four 10/100 Base-T Ethernet ports, a Wi-Fi Protected Setup (WPS)/ Wi-Fi switch button, and is backward compatible with existing 802.11b (11Mbps) and 11g (54bps) equipment.
1.3 Your ADSL modem router DSL-N12HP 300Mbps Wi-Fi ADSL Modem Router 4. 3. 2. 1. Power LED Off: No power. Solid green: Device is ready. Flashing green: Upgrade is in process. Solid red: POST (Power On Self Test) failure (not bootable) or device malfunction. NOTE: A malfunction is any error of internal sequence or state that will prevent the device from connecting to the DSLAM or passing customer data.
Wi-Fi LED Off: No Wi-Fi signal. Solid green: Wireless system is ready. Flashing green: Transmitting or receiving data via wireless connection. LAN 1~4 LED Off: No power or no physical connection. Solid green: Has physical connection to an Ethernet network. Flashing green: Transmitting or receiving data via wireless connection. WPS and Wi-Fi on/off button Press and hold this button more than 5 seconds to activate WPS. Ensure that the WPS is enabled in Wireless > Security page).
1.4 Positioning your ADSL modem router For the best wireless signal transmission between the ADSL modem router and the network devices connected to it, ensure that you: • • • • • Place the ADSL modem router in a centralized area for a maximum wireless coverage for the network devices. Keep the device away from metal obstructions and away from direct sunlight. To prevent signal interference or loss, keep the device away from 802.11g or 20MHz only Wi-Fi devices, 2.
1.5 Setup Requirements To set up your wireless network, you need a computer that meets the following system requirements: • Ethernet RJ-45 (LAN) port (10Base-T/100Base-TX) • IEEE 802.11b/g/n wireless capability • An installed TCP/IP service • Web browser such as Internet Explorer, Firefox, Safari, or Google Chrome NOTES: • If your computer does not have built-in wireless capabilities, you may install an IEEE 802.11b/g/n WLAN adapter to your computer to connect to the network.
4. 3. 2. 1. Wall Power Outlet Power DSL Wall telephone outlet Splitter Phone LAN Computer To set up your ADSL modem router via wired connection: 1. Connect one end of the RJ-11 cable to the ADSL port of your ADSL modem router, and connect the other end to the ADSL port of your splitter. 2. Using a network cable, connect your computer to your ADSL modem router’s LAN port. 3. Insert your ADSL modem router’s power adapter to the DC-IN port and plug it to a power outlet.
2 Getting started 2.1 Default settings Your ASUS Wireless ADSL Modem Router comes with an intuitive web graphical user interface (GUI) that allows you to easily configure its various features through a web browser such as Internet Explorer, Firefox, Safari, or Google Chrome. NOTE: The features may vary with different firmware versions. The factory default settings of this device are summarized below. • • • • LAN IP address: 192.168.1.1 LAN subnet mask: 255.255.255.
2.2 IP configuration DHCP MODE When the DSL-N12HP powers up, the onboard DHCP server will switch on. Basically, the DHCP server issues and reserves IP addresses for LAN devices, such as your PC. To obtain an IP address from the DCHP server, follow the steps provided below. NOTE: The following procedure assumes you are running Windows® 7. However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details. 1.
3. To obtain the IPv4 IP settings automatically, tick Obtain an IP address automatically. To obtain the IPv6 IP settings automatically, tick Obtain an IPv6 address automatically. 4. Click OK when done. If you experience difficulty with DHCP mode, you can try static IP mode instead. STATIC IP MODE In static IP mode, you assign IP settings to your PC manually. Follow these steps to configure your PC IP address to use subnet 192.168.1.x. NOTE: The following procedure assumes you are running Windows® 7.
1. Click Start > Control Panel > Network and Internet > Network and Sharing Center > Manage network connections. 2. Select Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), then click Properties. 3. Change the IP address to the 192.168.1.x (1
2.3 Logging into the Web GUI To log into the web GUI: 1. On your web browser, manually key in the ADSL modem router’s default IP address: 192.168.1.1 NOTE: For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device. For remote access (i.e. WAN), use the IP address shown on the Device Information screen and login with remote username and password. 2. On the login page, key in the default user name (admin) and password (admin).
2.4 Quick Internet Setup (QIS) Wizard with Auto-detection The Quick Internet Setup (QIS) function guides you in quickly setting up your Internet connection. NOTE: When setting the Internet connection for the first time, press the Reset button on your ADSL modem router to reset it to its factory default settings. For more details, refer to the section 4.2.5 Update Software of this user manual. To use QIS with auto-detection: 1. Log into the Web GUI. The QIS page launches automatically.
2. After successfully logging in for the first time, the Device Info page displays. 3. Click the Quick Internet Setup tab on the left side of the screen. 4. Key in the PPP username and PPP password that you obtained from your Internet Service Provider (ISP), assign the network name (SSID) and security key for your wireless connection, select your local time zone from the drop-down menu, and click Apply/Save when done.
5. Click Next to complete the setup and go to the Device Info page. NOTE: Change the router password to prevent unauthorized access to your ASUS wireless router. 2.5 Connecting to your wireless network After setting up your ADSL modem router via QIS, you can connect your computer or other smart devices to your wireless network. To connect to your network: 1. On your computer, click the network icon in the notification area to display the available wireless networks. 2.
3 Configuring the General settings 3.1 Device Information You can reach this page by clicking on the Device Info icon located on the left side of the screen. The Device Info Summary screen displays at startup. This screen shows hardware, software, IP settings and other related information.
3.1.1 WAN Click the WAN tab to display the configured PVC(s). Field Description Interface Name of the interface for WAN Description Name of the WAN connection Type Shows the connection type VlanMuxId Shows 802.
3.1.2 Traffic Statistics This selection provides LAN, WAN, xTM and xDSL statistics. Click the Traffic tab to display the following. Click Reset Statistics to perform a manual update.
LAN Statistics This screen shows data traffic statistics for each LAN interface. Select LAN from the drop-down menu.
WAN Statistics This screen shows data traffic statistics for each WAN interface. Select WAN from the drop-down menu.
xTM Statistics The following figure shows ATM (Asynchronous Transfer Mode)/ PTM (Packet Transfer Mode) statistics. Select xTM from the drop-down menu.
xDSL Statistics The xDSL Statistics screen displays information corresponding to the xDSL type.
Click the Reset Statistics button to refresh this screen. Field Description Mode ADSL2, ADSL2+ Traffic Type ATM Status Lists the status of the DSL link Link Power State Link output power state. phyR Status Shows the status of PhyR™ (Physical Layer Re-Transmission) impulse noise protection Line Coding (Trellis) Trellis On/Off SNR Margin (0.1 dB) Signal to Noise Ratio (SNR) margin Attenuation (0.1 dB) Estimate of average loop attenuation in the downstream direction. Output Power (0.
HEC Errors Total Number of Header Error Checksum errors OCD Errors Total Number of Out-of-Cell Delineation errors LCD Errors Total number of Loss of Cell Delineation Total Cells Total number of ATM cells (including idle + data cells) Data Cells Total number of ATM data cells Bit Errors Total number of bit errors Total ES Total Number of Errored Seconds Total SES Total Number of Severely Errored Seconds Total UAS Total Number of Unavailable Seconds xDSL BER TEST Click xDSL BER Test on the x
Click Start to start the test or click Close to cancel the test. After the BER testing is complete, the pop-up window will display as follows. xDSL TONE GRAPH Click Draw Graph on the xDSL Statistics screen and a pop-up window will display the DSL line statistics.
3.1.3 Route Click the Route tab to display the routes that the DSL-N12HP has found. Field Description Destination Destination network or destination host Gateway Next hop IP address Subnet Mask Subnet Mask of Destination Flag U: route is up !: reject route G: use gateway H: target is a host R: reinstate route for dynamic routing D: dynamically installed by daemon or redirect M: modified from routing daemon or redirect 30 Metric The 'distance' to the target (usually counted in hops).
3.1.4 Clients Status Click the Clients Status tab to display the Client information.
3.1.5 DHCP Click the DHCP tab to display all DHCP Leases. Select DHCPv4 from the drop-down menu. Field Description Hostname Shows the host name of device/host/PC MAC Address Shows the Ethernet MAC address of the device/host/PC IP Address Shows IP address of device/host/PC Expires In Shows how much time is left for each DHCP Lease Select DHCPv6 from the drop-down menu.
3.1.6 NAT Session Click the NAT Session tab to display the following. Click Show All to display the following.
3.1.7 IPv6 Click the IPv6 tab to display the following. IPv6 Info Select IPv6 Info from the drop-down menu.
IPv6 Neighbor Select IPv6 Neighbor from the drop-down menu. Field Description IPv6 Address Ipv6 address of the device(s) found Flags Status of the neighbor device HW Address MAC address of the neighbor device Device Interface from which the device is located IPv6 Route Select IPv6 Route from the drop-down menu.
3.2 Basic Setup You can reach this page by clicking on the Basic Setup icon located on the left side of the screen. This will bring you to the following screen.
3.2.1 Layer 2 Interface Add or remove ATM and ETH WAN interface connections here. Click Add to create a new ATM interface (see Appendix E Connection Setup). NOTE: Up to 8 ATM interfaces can be created and saved in flash memory. To remove a connection, select its Remove column radio button and click Remove.
3.2.1 Layer 2 Interface Add or remove ATM and ETH WAN interface connections here. Click Add to create a new ATM interface (see Appendix E Connection Setup). NOTE: Up to 8 ATM interfaces can be created and saved in flash memory. To remove a connection, select its Remove column radio button and click Remove. 3.2.2 WAN Service Setup This screen allows for the configuration of WAN interfaces. Click the WAN Service tab to display the following.
Click Add to create a new connection. For connections on ATM or ETH WAN interfaces see Appendix E - Connection Setup. To remove a connection, select its Remove column radio button and click Remove. Field Description Interface Name of the interface for WAN Description Name of the WAN connection Type Shows the connection type Vlan8021p VLAN ID is used for VLAN Tagging (IEEE 802.1Q) VlanMuxId Shows 802.
3.2.3 LAN Click the LAN tab to display the following. Configure the LAN interface settings and then click Apply/Save. Consult the field descriptions below for more details. GroupName: Select an Interface Group. 1st LAN INTERFACE IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port.
Enable Enhanced IGMP: Enable by ticking the checkbox. IGMP packets between LAN ports will be blocked. Enable LAN side firewall: Enable by ticking the checkbox. DHCP Server: To enable DHCP, select Enable DHCP server and enter Start and End IP addresses and the Leased Time. This setting configures the router to automatically assign IP, default gateway and DNS server addresses to every PC on your LAN. Setting TFTP Server: Enable by ticking the checkbox. Then, input the TFTP server address or an IP address.
2ND LAN INTERFACE To configure a secondary IP address, tick the checkbox outlined (in RED) below. IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port.
3.2.4 IPv6 Click the IPv6 tab to display the following.
LAN IPv6 Auto Configuration Select IPv6 LAN Auto Configuration from the drop-down menu. Configure the LAN interface settings and then click Save/Apply.
Consult the field descriptions below for more details.
To add an entry, enter MAC address and Interface ID and then click Apply/Save. To remove an entry, tick the corresponding checkbox in the Remove column and then click Remove Entries.
Field Description Enable RADVD Enable use of router advertisement daemon RA interval Min(sec): Minimum time to send router advertisement RA interval Max(sec): Maximum time to send router advertisement Reachable Time(ms): The time, in milliseconds that a neighbor is reachable after receiving reachability confirmation Default Preference: Preference level associated with the default router MTU (bytes): MTU value used in router advertisement messages to insure that all nodes on a link use the same
Static ARP/IP Neighbor Configuration Select Static ARP/IP Neighbor Configuration from the dropdown menu. Click the Add button to display the following. Click Apply/Save to apply and save the settings.
3.2.5 Security To display this function, you must enable the firewall feature in WAN Setup. For detailed descriptions, with examples, please consult Appendix A - Firewall. Click the Security tab to display the following.
IP Filtering This screen sets filter rules that limit IP traffic (Outgoing/ Incoming). Multiple filter rules can be set and each applies at least one limiting condition. For individual IP packets to pass the filter all conditions must be fulfilled. NOTE: This function is not available when in bridge mode. Instead, MAC Filtering performs a similar function. Select IP Filtering Setup from the drop-down menu.
To add a filter (to allow incoming IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Apply/Save. Consult the table below for field descriptions. Field Description Filter Name The filter rule label. IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Policy Permit/Drop packets specified by the firewall rule. Source IP address Enter source IP address. Source Port (port or port:port) Enter source port number or range.
OUTGOING IP FILTER By default, all outgoing IP traffic is allowed, but IP traffic can be blocked with filters. To add a filter (to block some outgoing IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Apply/Save. Consult the table below for field descriptions. Field 52 Description Filter Name The filter rule label. IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Source IP address Enter source IP address.
MAC Filtering NOTE: This option is only available in bridge mode. Other modes use IP Filtering to perform a similar function. Each network device has a unique 48-bit MAC address. This can be used to filter (block or forward) packets based on the originating device. MAC filtering policy and rules for the DSL-N12HP can be set according to the following procedure. The MAC Filtering Global Policy is defined as follows.
Click Save/Apply to save and activate the filter rule. Consult the table below for detailed field descriptions.
3.2.6 Parental Control This selection provides WAN access control functionality. Click on the Parental Control tab to display the following. Time Restriction This feature restricts access from a LAN device to an outside network through the device on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section Internet Time, so that the scheduled times match your local time. Select Time Restriction from the drop-down menu.
Click Add to display the following screen. See below for field descriptions. User Name: A user-defined label for this restriction. Browser's MAC Address: MAC address of the PC running the browser. Other MAC Address: MAC address of another LAN device. Days of the Week: The days the restrictions apply. Start Blocking Time: The time the restrictions start. End Blocking Time: The time the restrictions end. Click Apply/Save to add a time restriction.
URL Filter This screen allows for the creation of a filter rule for access rights to websites based on their URL address and port number. Select URL Filter from the drop-down menu. Select the Deny radio button to deny access to the websites listed. Select the Allow radio button to restrict access to only those listed websites. Then click Add to display the following screen. Enter the URL address and port number then click Apply/Save to add the entry to the URL filter.
A maximum of 100 entries can be added to the URL Filter list. 3.2.7 Routing The following routing functions are accessed from this menu: Default Gateway, Static Route, Policy Routing, RIP and IPv6 Static Route. NOTE: In bridge mode, the RIP menu option is hidden while the other menu options are shown but ineffective. Click the Routing tab to display the following.
Default Gateway Select Default Gateway from the drop-down menu. Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again.
Static Route This option allows for the configuration of static routes by destination IP. Click Add to create a static route or click Remove to delete a static route. Select Static Route from the drop-down menu. Click Add to display the following screen. IP Version: Select the IP version to be IPv4. Destination IP address/prefix length: Enter the destination IP address. Interface: select the proper interface for the rule. Gateway IP Address: The next-hop IP address. Metric: The metric value of routing.
Policy Routing This option allows for the configuration of static routes by policy. Select Policy Routing from the drop-down menu. Click Remove to delete an entry. Click Add to display the following. Complete the form and click Apply/Save to create a policy.
RIP Configuration Select RIP Configuration from the drop-down menu. To activate RIP for the WAN Interface, select the desired RIP version and operation and place a check in the "Enabled" checkbox. To stop RIP on the WAN Interface, uncheck the "Enabled" checkbox. Click Apply/Save to start/stop RIP and save the configuration.
3.3 Advanced Setup You can reach this page by clicking on the Advanced Setup icon located on the left side of the screen. This will bring you to the following screen. 3.3.1 NAT NOTE: To display this option, NAT must be enabled in at least one PVC. NAT is not an available option in Bridge mode. Click the NAT tab to display the following.
Virtual Servers Virtual Servers allow you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the internal server with private IP addresses on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum of 32 entries can be configured. Select Virtual Servers from the drop-down menu. To add a Virtual Server, click Add. The following will be displayed.
Consult the table below for field and header descriptions. Field Description Use Interface Select a WAN interface from the drop-down box. Select a Service User should select the service from the list. Custom Service User can enter the name of their choice. Server IP Address Enter the IP address for the server. Enable NAT Loopback Allows local machines to access virtual server via WAN IP Address External Port Start Enter the starting external port number (when you select Custom Server).
Port Triggering Some applications require that specific ports in the firewall be opened for access by the remote parties. Port Triggers dynamically 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.
Click Save/Apply to save and apply the settings. Consult the table below for field and header descriptions. Field Description Use Interface Select a WAN interface from the drop-down box. Select an Application User should select the application from the list. Custom Application User can enter the name of their choice. Trigger Port Start Enter the starting trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured.
DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. Select DMZ Host from the drop-down menu. Click Save/Apply to save and apply the settings. To Activate the DMZ host, enter the DMZ host IP address and click Save/Apply. To Deactivate the DMZ host, clear the IP address field and click Save/Apply.
IP Address Map Mapping Local IP (LAN IP) to some specified Public IP (WAN IP). Select IP Address Map from the drop-down menu. Field Description Rule The number of the rule Type Mapping type from local to public. Local Start IP The beginning of the local IP Local End IP The ending of the local IP Public Start IP The beginning of the public IP Public End IP The ending of the public IP Remove Remove this rule Click the Add button to display the following.
IPSEC ALG IPSEC ALG provides multiple VPN passthrough connection support, allowing different clients on LAN side to establish a secured IP Connection to the WAN server. Select IPSEC ALG from the drop-down menu. To enable IPSEC ALG, tick the checkbox and click Save. SIP ALG This page allows you to enable / disable SIP ALG. Select SIP ALG from the drop-down menu. To enable SIP ALG, tick the checkbox and click Save.
3.3.2 Quality of Service (QoS) NOTE: QoS must be enabled in at least one PVC to display this option. (See Appendix E - Connection Setup for detailed PVC setup instructions). Click the QoS tab to display the following.
Queue Management Configuration Select QoS Queue Setup from the drop-down menu. To Enable QoS tick the checkbox and select a Default DSCP Mark. Click Apply/Save to activate QoS. QoS and DSCP Mark are defined as follows: Quality of Service (QoS): This provides different priority to different users or data flows, or guarantees a certain level of performance to a data flow in accordance with requests from Queue Prioritization.
QoS Queue Setup Configure queues with different priorities to be used for QoS setup. In ATM mode, maximum 16 queues can be configured. In PTM mode, maximum 8 queues can be configured. For each Ethernet interface, maximum 3 queues can be configured. Select QoS Queue Setup from the drop-down menu. To add a queue, click the Add button. To remove queues, check their remove-checkboxes (for user created queues), then click the Remove button.
The Enable button will scan through every queue in the table. Queues with enable-checkbox checked will be enabled. Queues with enable-checkbox un-checked will be disabled. The enable-checkbox also shows status of the queue after page reload. Note that if WMM function is disabled in Wireless Page, queues related to wireless will not take effect. This function follows the Differentiated Services rule of IP QoS. You can create a new Queue entry by clicking the Add button.
QoS Policer Setup Select QoS Policer Setup from the drop-down menu. To remove policers, check their remove-checkboxes, then click the Remove button. The Enable button will scan through every policers in the table. Policers with enable-checkbox checked will be enabled. Policers with enable-checkbox un-checked will be disabled. The enable-checkbox also shows status of the policer after page reload. To add a policer, click the Add button.
Click Apply/Save to save the policer.
QoS Classification Setup The network traffic classes are listed in the following table. Select QoS Classification Setup from the drop-down menu. Click Add to configure a network traffic class rule and Enable to activate it. To delete an entry from the list, click Remove. This screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one logical condition.
Click Apply/Save to save and activate the rule. Field Description Traffic Class Name Enter a name for the traffic class. Rule Order Last is the only option. Rule Status Disable or enable the rule. Classification Criteria 78 Class Interface Select an interface (i.e. Local, eth0-4, wl0) Ether Type Set the Ethernet type (e.g. IP, ARP, IPv6).
Field Description Destination MAC Address A packet belongs to SET-1 then the result that the Destination MAC Address of its header binary-AND to the Destination MAC Mask must equal to the result that this field binary-AND to the Destination MAC Mask. Destination MAC Mask This is the mask used to decide how many bits are checked in Destination MAC Address.
3.3.4 DNS Click the DNS tab to display the following.
DNS Server Configuration Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
Dynamic DNS The Dynamic DNS service allows you to map a dynamic IP address to a static hostname in any of many domains, allowing the DSLN12HP to be more easily accessed from various locations on the Internet. Select Dynamic DNS from the drop-down menu. To add a dynamic DNS service, click Add. The following screen will display.
Click Apply/Save to save your settings. Consult the table below for field descriptions.
DNS Entries The DNS Entry page allows you to add domain names and IP address desired to be resolved by the DSL router. Select Dynamic DNS from the drop-down menu. Choose Add or Remove to configure DNS Entry. The entries will become active after save/reboot. Enter the domain name and IP address that needs to be resolved locally, and click the Add Entry button.
3.3.5 DSL The DSL Settings screen allows for the selection of DSL modulation modes. For optimum performance, the modes selected should match those of your ISP. Click the DSL tab to display the following. DSL Mode Data Transmission Rate - Mbps (Megabits per second) G.Dmt Downstream: 12 Mbps Upstream: 1.3 Mbps G.lite Downstream: 4 Mbps Upstream: 0.5 Mbps T1.413 Downstream: 8 Mbps Upstream: 1.0 Mbps ADSL2 Downstream: 12 Mbps Upstream: 1.
Options Description Bitswap Enable Enables adaptive handshaking functionality SRA Enable Enables Seamless Rate Adaptation (SRA) Select DSL LED behavior Normal (TR-68 compliant): Select this option for DSL LED to operate normally (See section 1.3 Your ADSL modem router) Off:DSL LED will always be OFF G997.
3.3.6 DNS Proxy DNS proxy receives DNS queries and forwards DNS queries to the Internet. After the CPE gets answers from the DNS server, it replies to the LAN clients. Configure DNS proxy with the default setting, when the PC gets an IP via DHCP, the domain name, Home, will be added to PC’s DNS Suffix Search List, and the PC can access route with “ASUS.Home”. Click the DNS Proxy tab to display the following. Click Apply/Save to implement new configuration settings.
3.3.7 Interface Grouping Interface Grouping supports multiple ports to PVC and bridging groups. Each group performs as an independent network. To use this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button removes mapping groups, returning the ungrouped interfaces to the Default group. Only the default group has an IP interface. Click the Interface Grouping tab to display the following. To add an Interface Group, click Add.
Click Apply/Save to implement new configuration settings.
Automatically Add Clients With Following DHCP Vendor IDs: Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Interface Grouping is enabled. For example, imagine there are 4 PVCs (0/33, 0/36, 0/37, 0/38). VPI/ VCI=0/33 is for PPPoE while the other PVCs are for IP set-top box (video).
3.3.7 IP Tunnel Click on the IP Tunnel tab to display the following. IPv6inIPv4 Configure 6in4 tunneling to encapsulate IPv6 traffic over explicitly-configured IPv4 links. Select 6in4 Tunnel Configuration from the drop-down menu.
Click the Add button to display the following. Click Apply/Save to implement new configuration settings. Click Return to go back to the previous page.
IPv4inIPv6 Configure 4in6 tunneling to encapsulate IPv4 traffic over an IPv6only environment. Select 4in6 Tunnel Configuration from the drop-down menu. Click the Add button to display the following. Click Apply/Save to implement new configuration settings. Click Return to go back to the previous page.
Field 94 Description Tunnel Name Input a name for the tunnel Mechanism Mechanism used by the tunnel deployment Associated WAN Interface Select the WAN interface to be used by the tunnel Associated LAN Interface Select the LAN interface to be included in the tunnel Manual/Automatic Select automatic for point-to-multipoint tunneling/ manual for point-to-point tunneling AFTR Address of Address Family Translation Router
3.4 Wireless You can reach this page by clicking the Wireless icon located on the left side of the screen.
3.4.1 Basic The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. Click the Basic tab to display the following. Click Apply/Save to apply the selected wireless options.
Consult the table below for descriptions of these options. Field Description Enable Wireless A checkbox that enables or disables the wireless LAN interface. When selected, a set of basic wireless options will appear. Hide SSID Select the checkbox to enable this function. Set AP isolated Select the checkbox to enable this function.
3.4.2 Security The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Click the Security tab to display the following. Please see Appendix F for WPS setup instructions. Click Apply/Save to implement new configuration settings. WIRELESS SECURITY Setup requires that the user configure these settings using the Web GUI (see the table below).
Select SSID Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that client will not be granted access. Network Authentication This option specifies whether a network key is used for authentication to the wireless network. If network authentication is set to Open, then no authentication is provided. Despite this, the identity of the client is still verified.
WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key. Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.
3.4.3 MAC Filter This option allows access to the router to be restricted based upon MAC addresses. Click the MAC Filter tab to display the following. To add a MAC Address filter, click the Add button shown below. To delete a filter, select it from the MAC Address table below and click the Remove button. Option Description Select SSID Select the wireless network name from the drop-down box. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN.
3.4.4 Wireless Bridge This screen allows for the configuration of wireless bridge features of the Wi-Fi interface. See the table beneath for detailed explanations of the various options. Click the Wireless Bridge tab to display the following. Click Apply/Save to implement new configuration settings. Feature 102 Description AP Mode Selecting Wireless Bridge (aka Wireless Distribution System) disables Access Point (AP) functionality, while selecting Access Point enables AP functionality.
3.4.5 Advanced The Advanced screen allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used. Click the Wireless Bridge tab to display the following.
Field 104 Description Band Set to 2.4 GHz for compatibility with IEEE 802.11x standards. The new amendment allows IEEE 802.11n units to fall back to slower speeds so that legacy IEEE 802.11x devices can coexist in the same network. IEEE 802.11g creates data-rate parity at 2.4 GHz with the IEEE 802.11a standard, which has a 54 Mbps rate at 5 GHz. (IEEE 802.11a has other differences compared to IEEE 802.11b or g, such as offering more channels.
Field Description Basic Rate Setting for basic transmission rate. Fragmentation Threshold A threshold, specified in bytes, that determines whether packets will be fragmented and at what size. On an 802.11 WLAN, packets that exceed the fragmentation threshold are fragmented, i.e., split into, smaller units suitable for the circuit size. Packets smaller than the specified fragmentation threshold value are not fragmented. Enter a value between 256 and 2346.
3.4.6 Site Survey The graph displays wireless APs found in your neighborhood by channel. Click the Site Survey tab to display the following.
3.4.7 Station Info This page shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN. Click the Station Info tab to display the following. Consult the table below for descriptions of each column heading. Field Description MAC Lists the MAC address of all the stations. Associated Lists all the stations that are associated with the Access Point, along with the amount of time since packets were transferred to and from each station.
4 Configuring the System settings 4.1 Diagnostics You can reach this page by clicking on the Diagnostics icon located on the left side of the screen. 4.1.1 Individual Tests The first Diagnostics screen is a dashboard that shows overall connection status. Click the Diagnostics tab to display the following. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent.
4.1.2 Uptime Status This page shows System, DSL, ETH and Layer 3 uptime. If the DSL line, ETH or Layer 3 connection is down, the uptime will stop incrementing. If the service is restored, the counter will reset and start from 0. A Bridge interface will follow the DSL or ETH timer. Click the Uptime Status tab to display the following. The ClearAll button will restart the counters from 0 or show Not Connected if the interface is down.
4.2 Management You can reach this page by clicking on the Management icon located on the left side of the screen. 4.2.1 Settings Click on the Settings tab to display the following. This includes Restore Default, Save Setting, and Restore Setting screens.
Restore Default Click the Restore button to restore factory default settings. After clicking Restore, the following window appears. Click OK to display the following. Close the browser and wait for 2 minutes before reopening it. It may also be necessary, to reconfigure your PC IP configuration to match any new settings. NOTE: This entry has the same effect as the Reset button. The DSLN12HP board hardware and the boot loader support the reset to default.
Save Setting To save the current configuration to a file on your PC, click the Save button. You will be prompted for backup file location. This file can later be used to recover settings on the Restore Setting screen, as described below. Upload Setting This option recovers configuration files previously saved using Save Setting. Press the Browse… button to search for the file, then click the Upload button to restore settings.
4.2.2 System Log This function allows a system log to be kept and viewed upon request. Click the System Log tab to display the following. Select the desired values and click Apply/Save to configure the system log options. Consult the table below for detailed descriptions of each system log option. Field Log Description Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled.
Field Description Log Level Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the DSL-N12HP SDRAM. When the log buffer is full, the newer event will wrap up to the top of the log buffer and overwrite the old event. By default, the log level is “Debugging”, which is the lowest critical level.
4.2.3 Internet Time This option automatically synchronizes the router time with Internet timeservers. Click the Internet Time tab to display the following. To enable time synchronization, tick the corresponding checkbox, choose your preferred time server(s), select the correct time zone offset, and click Apply/Save. NOTE: Internet Time must be activated to use Parental Control.
4.2.4 Access Control Click the Access Control tab to display the following. Passwords This screen is used to configure the user account access passwords for the device. Select Access Control - Accounts/Passwords from the dropdown menu. Use the fields to update passwords for the accounts administration. NOTE: Passwords may be as long as 16 characters but must not contain a space. Click Apply/Save to apply and save the settings.
Service Access The Services option limits or opens the access services over the LAN or WAN. Select Access Control – Service Access from the drop-down menu. These access services available are: HTTP, SSH, TELNET, HTTPS and ICMP. Enable a service by selecting its drop-down list box. Click Apply/Save to activate.
IP Address The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets. The services are the system applications listed in the Service Control List beside ICMP. Select Access Control - IP Address from the drop-down menu. Click the Add button to display the following.
4.2.5 Update Software This option allows for firmware upgrades from a locally stored file. Click the Update Software tab to display the following. 1. Obtain an updated software image file from your ISP. 2. Select the configuration from the drop-down menu. Configuration options: No change – upgrade software directly. Erase current config – If the router has save_default configuration, this option will erase the current configuration and restore to save_default configuration after software upgrade.
4.2.6 Feedback Your feedback is very important to us and will help to improve the firmware of DSL-N12HP. If you have any comments, suggestions or connection issue, complete the form below, these information along with current DSL logs will be send to ASUS Support Team. In order to allow us to respond to your feedback, kindly ensure that you have entered your e-mail correctly. Click the Feedback tab to display the following. Upon completing the form, click Send to submit.
5 Logout & Reboot To log out from the device simply click the Logout button at the top of your screen. When the following window pops up, click the OK button to exit the router. Upon successful exit, the following message will be displayed.
To reboot the device simply click the Reboot button at the top of your screen. While rebooting, the following message will be displayed.
Appendix A - Firewall STATEFUL PACKET INSPECTION Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. DENIAL OF SERVICE ATTACK Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
This filter will Drop all TCP packets coming from the LAN with IP Address/Subnet Mask of 192.168.1.45/24 having a source port of 80 irrespective of the destination. All other packets will be Accepted. Example 2: Filter Name: Out_Filter2 Protocol: UDP Source IP Address: 192.168.1.45 Source Subnet Mask: 255.255.255.0 Source Port: 5060:6060 Dest. IP Address: 172.16.13.4 Dest. Subnet Mask: 255.255.255.0 Dest.
Selected WAN interface: br0 This filter will ACCEPT all TCP packets coming from WAN interface “br0” with IP Address/Subnet Mask 210.168.219.45/16 with a source port of 80, irrespective of the destination. All other incoming packets on this interface are DROPPED. Example 2: Filter Name: In_Filter2 Protocol: UDP Policy: Allow Source IP Address: 210.168.219.45 Source Subnet Mask: 255.255.0.0 Source Port: 5060:6060 Dest. IP Address: 192.168.1.
Src. Interface: eth1 Dest. Interface: eth2 Addition of this rule drops all PPPoE frames going from eth1 to eth2 with a Destination MAC Address of 00:12:34:56:78:90 irrespective of its Source MAC Address. All other frames on this interface are forwarded. Example 2: Global Policy: Blocked Protocol Type: PPPoE Dest. MAC Address: 00:12:34:56:78:90 Source MAC Address: 00:34:12:78:90:56 Src. Interface: eth1 Dest.
Appendix B - Pin Assignments ETHERNET Ports (RJ45) ETHERNET LAN Ports (10/100Base-T) Table 1 Pin Definition Pin Definition 1 Transmit data+ 5 NC 2 Transmit data- 6 Receive data- 3 Receive data+ 7 NC 4 NC 8 NC Signals for ETHERNET WAN port (10/1001000Base-T) Table 2 Pin Signal name Signal definition 1 TRD+(0) Transmit/Receive data 0 (positive lead) 2 TRD-(0) Transmit/Receive data 0 (negative lead) 3 TRD+(1) Transmit/Receive data 1 (positive lead) 4 TRD+(2) Transmit/Receive d
Appendix C – Specifications Hardware Interface • RJ-11 X 1 for ADSL • RJ-45 X 4 for LAN (10/100 Base-T auto-sense) • WPS/Wi-Fi Button X 1 • On/Off Button X 1 • Reset Button X 1 • Wi-Fi Antenna X 2 WAN Interface • Downstream up to 12M for ADSL, 24 Mbps for ADSL2+; Upstream up to 1.3 Mbps, • ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2, Annex A/L/M LAN Interface • Standard IEEE 802.3, IEEE 802.3u • Support MDI/MDX • 10/100 Base T Auto-sense Wireless Interface • IEEE802.
Networking Protocols • RFC 2684 VC-MUX, LLC/SNAP encapsulations for bridged or routed packet • RFC 2364 PPP over AAL5 • IPoA, PPPoA, PPPoE, Multiple PPPoE sessions on single PVC, PPPoE pass-through • PPPoE filtering of on-PPPoE packets between WAN and LAN • Transparent bridging between all LAN and WAN interfaces • 802.1p/802.
Firewall/Filtering • Stateful Inspection Firewall • Stateless Packet Filter • Denial of Service (DOS): ARP attacks, Ping attacks, Ping of Death, LAND,SYNC, Smurf, Unreachable, Teardrop • TCP/IP/Port/interface filtering rules Support both incoming and outgoing filtering NAT/NAPT • Support Port Triggering and Port forwarding • Symmetric port-overloading NAT, Full-Cone NAT • Dynamic NAPT (NAPT N-to-1) • Support DMZ host • Virtual Server (Port forwarding) • VPN Passthrough (PPTP, L2TP, IPSec) Application Passth
Appendix D - SSH Client Unlike Microsoft Windows, Linux OS has a ssh client included. For Windows users, there is a public domain one called “putty” that can be downloaded from here: http://www.chiark.greenend.org. uk/~sgtatham/putty/download.html To access the ssh client you must first enable SSH access for the LAN or WAN from the Management > Access Control > Services menu in the Web GUI. To access the router using the Linux ssh client For LAN access, type: ssh -l root 192.168.1.
Appendix E - Connection Setup Creating a WAN connection is a two-stage process. 1 - Setup a Layer 2 Interface (ATM or Ethernet WAN). 2 - Add a WAN connection to the Layer 2 Interface. You can reach this page by clicking on the Basic Setup icon located on the left side of the screen. The following sections describe each stage in turn. E1 Layer 2 Interfaces Every layer2 interface operates in Multi-Service Connection (VLAN MUX) mode, which supports multiple connections over a single interface.
1. Click Add to create a new ATM interface. NOTE: To add WAN connections to one interface type, you must delete existing connections from the other interface type using the Remove button. This table is provided here for ease of reference. Field Description Interface WAN interface name.
There are many settings here including: VPI/VCI, DSL Link Type, Encapsulation Mode, Service Category, Connection Mode and Quality of Service. Here are the available encapsulations for each xDSL Link Type: • EoA- LLC/SNAP-BRIDGING, VC/MUX • PPPoA- VC/MUX, LLC/ENCAPSULATION • IPoA- LLC/SNAP-ROUTING, VC MUX 2. Click Apply/Save to confirm your choices.
On the next screen, check that the ATM interface is added to the list. For example, an ATM interface on PVC 0/35 in Default Mode with an EoA Link type is shown below. To add a WAN connection go to section E2 WAN Connections. E1.2 ETHERNET WAN Interfaces Follow these procedures to configure an Ethernet WAN interface. 1. Click Add to create an Ethernet WAN interface. This table is provided here for ease of reference. Field Description Interface/ (Name) WAN interface name.
2. Select an Ethernet port and Click Apply/Save to confirm your choices. On the next screen, check that the ETHERNET interface is added to the list.
E2 WAN Connections The DSL-N12HP supports one WAN connection for each interface, up to a maximum of 16 connections. 1. Click the WAN Service tab to display the following. 2. Click the Add button to create a WAN connection. The following screen will display. 3. Choose a layer 2 interface from the drop-down box and click Next. The WAN Service Configuration screen will display as shown below.
NOTE: The WAN services shown here are those supported by the layer 2 interface you selected in the previous step. If you wish to change your selection click the Back button and select a different layer 2 interface. 4. For VLAN Mux Connections only, you must enter Priority & VLAN ID tags. 5. You will now follow the instructions specific to the WAN service type you wish to establish. This list should help you locate the correct procedure: (1) For PPP over ETHERNET (PPPoE), go to page 134.
E2.1 PPP over ETHERNET (PPPoE) 1. Select the PPP over Ethernet radio button and click Next. You can also enable IPv6 by ticking the checkbox at the bottom of this screen. 2. On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
The settings shown above are described below. PPP SETTINGS The PPP Username, PPP password and the PPPoE Service Name entries are dependent on the particular requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. For Authentication Method, choose from AUTO, PAP, CHAP, and MSCHAP.
ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port. An external host can send a packet to the internal host, by sending a packet to the mapped external address. DIAL ON DEMAND The DSL-N12HP can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox.
ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox should not be selected to free up system resources for better performance. ENABLE FIREWALL If this checkbox is selected, the Security submenu will be displayed on the Advanced Setup menu after reboot.
PPPoE clients, otherwise disable it. The DSL-N12HP supports passthrough PPPoE sessions from the LAN side while simultaneously running a PPPoE client from non-PPPoE LAN devices. ENABLE IGMP MULTICAST PROXY Tick the checkbox to enable Internet Group Membership Protocol (IGMP) multicast. This protocol is used by IPv4 hosts to report their multicast group memberships to any neighboring multicast routers. NO MULTICAST VLAN FILTER Tick the checkbox to Enable/Disable multicast VLAN filter.
Click Next to continue or click Back to return to the previous step. 4. The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it, you must click the Reboot button at the top of the screen to reboot.
E2.2 IP over ETHERNET (IPoE) 1. Select the IP over Ethernet radio button and click Next. NOTE: For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
2. The WAN IP settings screen provides access to the DHCP server settings. You can select the Obtain an IP address automatically radio button to enable DHCP (use the DHCP Options only if necessary). However, if you prefer, you can instead use the Static IP address method to assign WAN IP address, Subnet Mask and Default Gateway manually. Click Next to continue or click Back to return to the previous step. If IPv6 is enabled, the following will also be shown.
3. This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox. Click Next to continue or click Back to return to the previous step. ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e.
ENABLE IGMP MULTICAST Tick the checkbox to enable Internet Group Membership Protocol (IGMP) multicast. IGMP is a protocol used by IPv4 hosts to report their multicast group memberships to any neighboring multicast routers. Enable WAN interface with base MAC Enable this option to use the router’s base MAC address as the MAC address for this WAN interface. 4. To choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step.
5. Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. If IPv6 is enabled, the following will also be shown. IPv6: Select a preferred wan interface as the system default IPv6 gateway. Click Next to continue or click Back to return to the previous step.
6. The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it, you must click the Reboot button at the top of the screen to reboot.
E2.3 Bridging 1. Select the Bridging radio button and click Next. NOTE: For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
2. The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to return to the previous screen. After clicking Apply/Save, the new service should appear on the main screen. To activate it, you must click the Reboot button at the top of the screen to reboot. NOTE: If this bridge connection is your only WAN service, the DSLN12HP will be inaccessible for remote management or technical support from the WAN.
E2.4 PPP over ATM (PPPoA) 1. Click Next to continue. 2. On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
PPP SETTINGS The PPP username and password are dependent on the requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. (Authentication Method: AUTO, PAP, CHAP, or MSCHAP.) ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port.
• ports, unless the packet is addressed to the device’s LAN IP address. The public IP address assigned by the remote side using the PPP/IPCP protocol is actually not used on the WAN PPP interface. Instead, it is forwarded to the PC LAN interface through DHCP. Only one PC on the LAN can be connected to the remote, since the DHCP server within the device has only a single IP address to assign to a LAN device.
ENABLE IGMP MULTICAST PROXY Tick the checkbox to enable Internet Group Membership Protocol (IGMP) multicast. This protocol is used by IPv4 hosts to report their multicast group memberships to any neighboring multicast routers. NO MULTICAST VLAN FILTER Tick the checkbox to Enable/Disable multicast VLAN filter. Enable WAN interface with base MAC Enable this option to use the router’s base MAC address as the MAC address for this WAN interface. 3. Choose an interface to be the default gateway.
4. Choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step. 5. The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it, you must click the Reboot button at the top of the screen to reboot.
E2.5 IP over ATM (IPoA) 1. Click Next to continue. 2. Enter the WAN IP settings provided by your ISP. Click Next to continue. 3. This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox. Click Next to continue or click Back to return to the previous step.
ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox should not be selected, so as to free up system resources for improved performance. ENABLE FULLCONE NAT This option becomes available when NAT is enabled.
4. Choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step. 5. Choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step.
6. The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it, you must click the Reboot button at the top of the screen to reboot.
Appendix F - WPS OPERATION This section shows the basic AP WPS Operation procedure. F1 Add Enrollee with Pin Method 1. Click on the Wireless tab on the left side of your screen. Then, click on the Security tab to display the following. 2. Select Enabled from the Enable WPS drop-down menu. Click the Apply/Save button at the bottom of the screen.
3. When the screen refreshes select the Radio button Enter STA Pin. 4. Input Pin from Enrollee Station (15624697 in this example) 5. Click Add Enrollee. 6. Operate Station to start WPS Adding Enrollee. F2 Add Enrollee with PBC Method 1. Press the WPS/Wi-Fi button on the back panel of the router to activate WPS PBC operation. 4. 3. 2. 1. 2. Operate Station (your dongle for example) to start WPS Adding Enrollee. 3. Press more than 5 seconds to trigger WPS.
Appendix G Notices ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus. com/english/Takeback.htm for the detailed recycling information in different regions.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Safety Information To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Declaration of Conformity for R&TTE directive 1999/5/EC Essential requirements – Article 3 Protection requirements for health and safety – Article 3.1a Testing for electric safety according to EN 60950-1 has been conducted. These are considered relevant and sufficient.
Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the ASUS Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.
canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent a ecter son fonctionnement.
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.
act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole.
be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
range of software distributed through that system in reliance on consistent application of that system; it is up to the author/ donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8.
For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
For Turkey only Authorised distributors in Turkey: BOGAZICI BIL GISAYAR SAN. VE TIC. A.S. Tel. No.: +90 212 3311000 Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10 AYAZAGA/ISTANBUL CIZGI Elektronik San. Tic. Ltd. Sti. Tel. No.: +90 212 3567070 Address: CEMAL SURURI CD. HALIM MERIC IS MERKEZI No: 15/C D:5-6 34394 MECIDIYEKOY/ ISTANBUL KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S. Tel. No.: +90 216 5288888 Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL AEEE Yönetmeliğine Uygundur.
ASUS Contact Information ASUSTeK COMPUTER INC. (Asia Pacific) Address Website 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 www.asus.com.tw Technical Support Telephone Support Fax Online support +886228943447 +886228907698 support.asus.com ASUS COMPUTER INTERNATIONAL (America) Address Telephone Fax Website Online support 800 Corporate Way, Fremont, CA 94539, USA +15107393777 +15106084555 usa.asus.com support.asus.
Networks Global Hotline Information Region Country Service Hours 09:00-13:00 ; 14:00-18:00 Mon-Fri 09:00-18:00 Mon-Fri Cyprus 800-92491 France Hungary 0033-170949400 0049-1805010920 0049-1805010923 (component support) 0049-2102959911 ( Fax ) 0036-15054561 Italy 199-400089 Greece 00800-44142044 Austria Netherlands/ Luxembourg Belgium Norway Sweden Finland Denmark Poland Spain Portugal Slovak Republic Czech Republic Switzerland-German Switzerland-French Switzerland-Italian United Kingdom Ireland R
Networks Global Hotline Information Region Country Australia New Zealand Japan Korea Thailand Asia-Pacific Singapore Malaysia Philippine India India(WL/NW) Indonesia Americas 180 Hotline Numbers 1300-278788 0800-278788 0800-1232787 0081-570783886 ( Non-Toll Free ) 0082-215666868 0066-24011717 1800-8525201 0065-64157917 0065-67203835 ( Repair Status Only ) 0060-320535077 1800-18550163 1800-2090365 0062-2129495000 500128 (Local Only) Vietnam 1900-555581 Hong Kong USA Canada Mexico 00852-35824770 1
Networks Global Hotline Information Region Middle East + Africa Country Egypt Saudi Arabia UAE Turkey South Africa Israel Romania Bosnia Herzegovina Bulgaria Balkan Countries Croatia Montenegro Serbia Slovenia Estonia Latvia Lithuania-Kaunas Lithuania-Vilnius Hotline Numbers Service Hours 800-2787349 09:00-18:00 Sun-Thu 800-1212787 09:00-18:00 Sat-Wed 00971-42958941 09:00-18:00 Sun-Thu 0090-2165243000 09:00-18:00 Mon-Fri 0861-278772 08:00-17:00 Mon-Fri *6557/00972-39142800 08:00-17:00 Sun-Thu *9770/0097
