User Guide Motherboard PR-DLS533
E1071 Checklist First Edition V1 February 2003 Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Features Notices ........................................................................................... vi Safety information ......................................................................... vii About this guide ............................................................................ viii How this guide is organized ................................................ viii Conventions used in this guide ............................................. ix Where to find more information .
Contents Safeguards 2.6 2.7 2.8 Expansion slots ................................................................. 2-11 2.6.1 Installing an expansion card ................................. 2-11 2.6.2 Configuring an expansion card .............................2-11 2.6.3 PCI slots .............................................................. 2-13 Switches and jumpers ...................................................... 2-14 2.7.1 Switches ..............................................................
Contents Chapter 5: OS Installation 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Support CD contents .......................................................... 5-1 5.1.1 Drivers ................................................................... 5-1 5.1.2 Management Sofware ............................................ 5-1 5.1.3 Utilities ................................................................... 5-2 5.1.4 Contact ..................................................................
Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing the ASUS PR-DLS533 motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the PR-DLS533 motherboard. It includes brief descriptions of the special attributes of the motherboard and the new technology it supports.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
ASUS contact information ASUSTeK COMPUTER INC. (Asia-Pacific) Address: General Tel: General Fax: General Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): Notebook (Tel): Desktop/Server (Tel): Support Fax: Support Email: Web Site: +886-2-2890-7121 (English) +886-2-2890-7122 (English) +886-2-2890-7123 (English) +886-2-2890-7698 tsd@asus.com.tw www.asus.com.
PR-DLS533 specifications summary CPU Support for Intel® Xeon™ processor On-die 512KB L2 cache Chipsets RCC Grand Champion LE Server (GCLE) RCC Champion South Bridge 5.0 (CSB5) RCC Champion I/O Bridge 2.
PR-DLS533 specifications summary Form Factor Extended ATX form factor: 12 in x 13 in (30.5 cm x 33 cm) Support CD contents Device drivers Management software Utilities Contact information * Specifications are subject to change without notice.
Chapter 1 This chapter describes the features of the PR-DLS533 motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
Chapter summary 1.1 Welcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................. 1-2 1.4 Motherboard overview ...................................
1.1 Welcome! Thank you for buying the ASUS® PR-DLS533 motherboard! The ASUS PR-DLS533 motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality server motherboards! The PR-DLS533 incorporates dual Intel® Xeon™ processors in 603/ 604-pin package coupled with the ServerWorks® Grand Champion Low End (GCLE) SystemSet to deliver a reliable and high performance dualprocessor server platform.
1.3 Special features 1.3.1 Product highlights Latest processor technology The PR-DLS533 motherboard supports the Intel® Xeon processor via dual 603/604-pin surface mount ZIF sockets. The processor features the Intel® NetBurst™ micro-architecture that includes hyper-pipelined technology, a rapid execution engine, a 533/400MHz system bus, and an execution trace cache to offer a significant increase in performance. See page 2-4 for more information.
Onboard LAN The motherboard comes with the Intel® 82540EM 32-bit PCI Gigabit Ethernet controller and the Intel® 82544GC 64-bit PCI-X Gigabit Ethernet controller to support the latest LAN technologies. The Intel® 82551QM Fast Ethernet controller is an option. Onboard VGA The ATI Rage-XL PCI-based VGA controller integrates an 8MB display SDRAM to provide onboard video solution.
1.3.2 Value-added solutions Temperature, fan, and voltage monitoring The CPU temperature is monitored by the ASUS ASIC to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection. The system voltage levels are monitored to ensure stable supply of current for critical components.
Auto fan off The system fans power off automatically when the system is in sleep mode. This feature reduces both power consumption and system noise. Chassis intrusion detection The motherboard supports chassis intrusion monitoring through the ASUS ASIC. A chassis intrusion event is retained in the system memory for more protection. Smart BIOS The 4Mbit firmware gives an easy-to-use interface that provides more control and protection to the motherboard.
1.4 Motherboard overview Before you install the PR-DLS533 motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may damage the board and its components. 1.4.1 Major components The following are the major components of the PR-DLS533 motherboard as pointed out in the picture on page 1-7. 1. DDR DIMM sockets 2.
1 2 3 4 5 6 20 19 18 7 8 17 16 15 14 21 27 13 12 11 10 9 22 26 25 24 ASUS PR-DLS533 motherboard user guide 23 1-7
1.4.2 Core specifications 1-8 1 DDR DIMM sockets. These six 184-pin DIMM sockets support up to 12GB system memory using registered ECC PC2100/1600 DDR DIMMs. 2 8-pin 12V SSI power connector. This power connector is for an ATX power supply. 3 24/20-pin ATX power connector. This power connector is for an ATX power supply. 4 ServerWorks® Grand Champion LE north bridge (CMIC-LE). The Champion Memory and I/O Controller LE (CMIC-LE) acts as the host bridge of the Grand Champion Low End (GCLE) SystemSet.
9 Ultra320 SCSI connectors. These dual-channel 68-pin Ultra320 SCSI connectors support up to 30 SCSI devices, and data transfers of 320Mbps. 10 LSI® Ultra320 SCSI controller. The LSI 53C1030 SCSI controller supports up to 30 SCSI devices through the onboard dual-channel SCSI connectors. 11 Flash ROM. This 4Mb flash ROM contains the programmable BIOS program. 12 ASUS ASIC. This chip performs multiple system functions that include hardware and system voltage monitoring, among others.
18 LPC super I/O controller. This Low Pin Count (LPC) interface provides the commonly used Super I/O functionality. The chipset supports UART compatible serial ports, one parallel port with EPP and ECP capabilities, a floppy drive, and PS/2 keyboard and mouse. 19 ServerWorks® 64-bit I/O Bridge (CIOB-X2). (See description in item 13.) 20 Intel® 82544GC 64-bit PCI-X Gigabit Ethernet controller. This LAN controller is integrated Ethernet LAN component that supports 10/100/1000Mbps data rates.
Chapter 2 This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
Chapter summary 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) ..................... 2-3 2.5 System memory ............................................. 2-8 2.6 Expansion slots ............................................ 2-11 2.7 Switches and jumpers ................................. 2-14 2.8 Connectors .....
2.1 Motherboard installation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The PR-DLS533 uses the extended ATX form factor that measures 12 inches x 13 inches (30.5 x 33 cm). Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause you physical injury and damage motherboard components. 2.1.
2.2 Motherboard layout 33cm (13in) PS/2 CON12V SYSFAN3 T: Mouse B: Keyboard CPUFAN1 DDR DIMMA1 (64/72 bit, 184-pin module) DDR DIMMA2 (64/72 bit, 184-pin module) COM1 DDR DIMMB1 (64/72 bit, 184-pin module) PARALLEL PORT SYSFAN2 mPGA 604 USB1 USB2 ATX_POWER DDR DIMMB2 (64/72 bit, 184-pin module) DDR DIMMC1 (64/72 bit, 184-pin module) DDR DIMMC2 (64/72 bit, 184-pin module) ® PR-DLS533 RJ-45 (LAN-2) ServerWorks ® CMIC-LE North Bridge Intel 82544GC Gigabit Ethernet RJ-45 (LAN-1) CLKSW 30.
2.3 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. 3. Hold components by the edges to avoid touching the ICs on them. 4.
2.4.2 Installing the CPU Note in the illustration that the CPU has a gold triangular mark on one corner. This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket. Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU! CPU Socket 1 (outer socket) CPU Socket 2 (inner socket) 1. The motherboard supports either one or two CPUs. If you are installing only one CPU, you MUST install it in CPU socket 1. 2.
Follow these steps to install a CPU. 1. Locate the 603/604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 115° angle. Make sure that the socket lever is lifted up to at least 115° angle, otherwise the CPU does not fit in completely. 2. Position the CPU above the socket as shown. 3. Carefully insert the CPU into the socket until it fits in place. Marked Corner The CPU fits only in one correct orientation.
2.4.3 Installing the CPU heatsink and fan The Intel® Xeon™ processors require specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan. 1. Place the heatsink and fan assembly on top of the installed CPU, making sure that it fits in place. 2. Hook one end of the retention bracket into the protruding tab on the corner of the plastic retention base. (The retention base comes installed with the motherboard.
3. Use a small flat screw driver to attach the other end of the bracket, while firmly holding down the heatsink and fan assembly. The middle hook of the bracket snaps in place if you properly attached the two ends. 4. As shown, the middle hook of the bracket snaps in place if you properly attached the two ends. 5. Do steps 2 to 4 to install the other bracket. 6.
2.5 System memory 2.5.1 Overview The motherboard comes with six Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 12GB system memory using 184-pin registered PC2100/1600 DIMMs with Serial Presence Detect (SPD) and Error Check and Correction (ECC). 104 Pins 80 Pins DDRA1 DDRA2 DDRB1 DDRB2 DDRC1 DDRC2 PR-DLS533 PR-DLS533 184-Pin DDR DIMM Sockets A DDR DIMM is keyed with a notch so that it fits in only one direction.
2.5.2 Memory Configurations The motherboard supports system memory of up to 12GB in a two-way interleaved configuration. As a rule, this configuration requires that you install identical DDR DIMMs (exactly the same type and size) in pairs. For example, if you installed a 512MB module into DDRA1, you must install the same type of 512MB module into DDRA2. The same rule applies to pairs DDRB1/DDRB2 and DDRC1/DDRC2.
2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM. 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. Unlocked Retaining Clip 3.
2.6 Expansion slots In the future, you may need to install expansion cards. The following subsections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.6.1 Installing an expansion card Follow these steps to install an expansion card. 1.
Standard Interrupt Assignments IRQ 0 1 2 3* 4* 5* 6 7* 8 9* 10* 11* 12* 13 14* 15* * Priority 1 2 N/A 11 12 13 14 15 3 4 5 6 7 8 9 10 Standard Function System Timer Keyboard Controller Programmable Interrupt Communications Port (COM2) Communications Port (COM1) Sound Card (sometimes LPT2) Floppy Disk Controller Printer Port (LPT1) System CMOS/Real Time Clock ACPI Mode when used IRQ Holder for PCI Steering IRQ Holder for PCI Steering PS/2 Compatible Mouse Port Numeric Data Processor Primary IDE Channel Se
2.6.3 PCI slots This motherboard implements the PCI-X (Peripheral Component Interconnect Extended) bus technology to support up to 133MHz data transfers, or about 1.06GB/s. This bus technology is primarily designed for servers to increase the performance of high bandwidth devices such as Gigabit Ethernet cards and Ultra320 SCSI interfaces.
2.7 Switches and jumpers 2.7.1 Switches The following figure shows the location and default settings of the DIP switches on the motherboard. Keep the default settings for stable system operation. CLKSW ON ON OFF 1 2 3 4 5 CONFIG_SW ON PR-DLS533 OFF ON 1 2 3 4 5 6 7 8 (Default) PR-DLS533 DIP Switches 1. CPU external frequency selection (CLKSW Switches 1-5) This option tells the clock generator what frequency to send the CPU. This allows the selection of the CPU’s external frequency (or Bus Clock).
2. CPU Core:Bus frequency multiple (CONFIG_SW Switches 5-8) This option sets the frequency multiple between the CPU internal and external frequencies. This must be set in conjunction with the CPU Bus Frequency. ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 15.0x 17.0x ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 20.0x 21.0x ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 22.0x 23.0x ON PR-DLS533 PR-DLS533 CPU Frequency Multiple Selection 1 2 3 4 5 6 7 8 24.0x 2.7.2 Jumpers 1.
2. 32-bit PCI Ethernet controller setting (3-pin LAN_SW) Set this jumper to pins 1-2 to enable the onboard Intel 82540EM 32-bit Gigabit Ethernet controller to support 10/100/1000 Mbps networking, or the Intel 82551QM Fast Ethernet controller to support 10BASE-T/ 100BASE-TX networking. Set to pins 2-3 to disable the controller. LAN_SW Enable (Default) Disable PR-DLS533 PR-DLS533 LAN_SW Setting 3.
4. SCSI setting (2-pin SCSI_EN) This jumper allows you to enable or disable the onboard SCSI feature. Keep the jumper open if you wish to install SCSI devices. Place a cap on the jumper to disable the onboard SCSI controller. SCSI_EN Enable (Default) Disable PR-DLS533 PR-DLS533 SCSI Setting 5. Clear RTC RAM (R452) These solder pads allow you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable.
3. IDE connectors (two 40-1 pin PRI_IDE/SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the black connector to the UltraDMA/100/66 master device. It is recommended that you connect non-UltraDMA/100/66 devices to the secondary IDE connector.
4. Chassis alarm lead (4-1 pin CHASSIS) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. By default, the pins labeled “Chassis Signal” and “Ground” are shorted with a jumper cap.
6. ATX power connectors (24/20-pin ATXPWR, 8-pin ATX12V) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 24/20-pin ATXPWR connector, this motherboard requires that you connect the 8-pin ATX +12V power plug to provide sufficient power to the CPU.
7. CPU, Chassis, and Power Fan Connectors (3-pin CPUFAN1, CPUFAN2, SYSFAN1, SYSFAN2, SYSFAN3) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components.
9. Zero Channel RAID slot (PCI-X5) The 64-bit/100MHz PCI-X slot (colored green) supports the LSI MegaRAID 320-0 or the Intel SRC ZCR (Zero-Channel RAID) card to provide advanced RAID functionality. The card supports RAID levels 0, 1, 5, multilevel 0/1 and 0/5, cache memory modules with ECC, and predictive caching capability. LSI MegaRAID 320-0 Zero Channel RAID Card PR-DLS533 PR-DLS533 Zero Channel RAID Slot 10.
IPMIDATA GND IPMICLK NC 11. IPMI connector (4-pin IPMI) The Intelligent Platform Management Interface (IPMI) connector is for the ASMC card. Connect the 4-pin ASMC interface cable to this connector. PR-DLS533 PR-DLS533 IPMI Connector 12. Wake-On-LAN Connector (3-pin WOL_CON) This connector supports a LAN card with a Wake-On-LAN output. The connector powers up the system when a wakeup packet or signal is received through the LAN card.
13. Two 68-pin Ultra320 SCSI Connectors (SCSI-A, SCSI-B) This motherboard has two 68-Pin Ultra320 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra320 standards.
14. Wake-On-Ring Connector (2-pin WOR) This connector connects to internal modem cards with a Wake-OnRing output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. For external modems, Wake-On-Ring is detected through the COM port. WOR 1 2 Ground Ring# PR-DLS533 PR-DLS533 Wake-On-Ring Connector 15. Hard disk activity LED (2-pin IDELED) This connector supplies power to the hard disk activity LED.
16. System panel connector (20-pin PANEL) This connector accommodates several system front panel functions. PLED Keylock Ground +5 V Power LED 10 Reset Ground 1 PWR Ground 20 +5 V MLED 11 Message LED PR-DLS533 Speaker Connector +5V IDELED+ IDELEDSpeaker Keyboard Lock Reset SW ATX Power Switch* PR-DLS533 System Panel Connectors • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED.
2-28 Chapter 2: Hardware information
Chapter 3 This chapter describes the power up sequence and gives information on the BIOS beep codes.
Chapter summary 3.1 Starting up for the first time .......................... 3-1 3.2 Powering off the computer ...........................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
3.2 Powering off the computer You must first exit the operating system and shut down the system before switching off the power. For ATX power supplies, you can press the ATX power switch after exiting or shutting down the operating system. If you use Windows 95/98/2000/XP, click the Start button, click Shut Down, then click the OK button to shut down the computer. The power supply should turn off after Windows shuts down.
Chapter 4 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-5 4.3 Main Menu ...................................................... 4-8 4.4 Advanced Menu ........................................... 4-15 4.5 Power Menu .................................................. 4-22 4.6 Boot Menu .................................................... 4-27 4.7 Server Menu ................................................. 4-30 4.
4.1 Managing and updating your BIOS 4.1.1 Creating a bootable disk AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. To determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. 1.
5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. 6. Type a filename and the path, for example, A:\XXX-XX.XXX, then press .
4.1.2 Updating the BIOS Update the BIOS only if you have problems with the motherboard and you are sure that the new BIOS revision will solve your problems. Careless updating may result to more problems with the motherboard! 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONTACT INFORMATION on page x for details) and save to the boot floppy disk you created earlier. 2. Boot from the floppy disk. 3. At the “A:\” prompt, type AFLASH and then press . 4.
7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary. This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears. 8. Follow the onscreen instructions to continue. If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems.
4.2 BIOS Setup program This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future.
4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure power management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System.
General help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. You may launch this screen from any menu by simply pressing or the + combination. The General Help screen lists the legend keys and their corresponding functions. Saving changes and exiting the Setup program See “4.8 Exit Menu” for detailed information on saving changes and exiting the setup program.
4.3 Main Menu When you enter the Setup program, the following screen appears. System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the or + keys to move between the hour, minute, and second fields. System Date [XX/XX/XXXX] Sets the system to the date that you specify (usually the current date).
Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. To set a password, highlight the appropriate field and press . Type in a password then press . You can type up to eight alphanumeric characters. Symbols and other characters are ignored. To confirm the password, type the password again and press . The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus.
4.3.1 Primary and Secondary Master/Slave Type [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu. If automatic detection fails, this may be because the hard disk drive is too old or too new. If the hard disk was already formatted on an older system, Setup may detect incorrect parameters.
[User Type HDD] Manually enter the number of cylinders, heads and sectors per track for the drive. Refer to the drive documentation or on the drive label for this information. After entering the IDE hard disk drive information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.
Translation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity. Configuration options: [LBA] [LARGE] [Normal] [Match Partition Table] [Manual] Cylinders This field configures the number of cylinders. Refer to the drive documentation to determine the correct value.
SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system that utilizes internal hard disk drive monitoring technology. This parameter is normally disabled because the resources used in the SMART monitoring feature may decrease system performance. Configuration options: [Disabled] [Enabled] PIO Mode [4] This option lets you set a PIO (Programmed Input/Output) mode for the IDE device.
4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second.
4.4 Advanced Menu CPU Speed [Manual] This field displays the auto-detected CPU speed. CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or off the CPU Level 1 and Level 2 built-in cache.
OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled]. Otherwise, leave to the default setting [Disabled]. Configuration options: [Disabled] [Enabled] USB Legacy Support [Auto] This motherboard supports Universal Serial Bus (USB) devices. The default of [Auto] allows the system to detect a USB device at startup. If detected, the USB controller legacy mode is enabled.
4.4.1 Chip Configuration Video Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor. It can greatly improve the display speed by caching the display data. You must set this to UC (uncacheable) if your display card cannot support this feature; otherwise your system may not boot. Configuration options: [UC] [USWC] Enhanced Memory Mapping [Enabled] This item allows you to enable or disable the enhanced memory mapping feature.
4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only] Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] These fields allow you to set the addresses for the onboard serial connectors.
Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows normal speed operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP] [ECP+EPP] ECP DMA Select [3] This field allows you to configure the parallel port DMA channel for the selected ECP mode.
4.4.3 PCI Configuration Slot 1, Slot 2, Slot 3, Slot 4, Slot 5, Slot 6 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15] PCI/VGA Palette Snoop [Disabled] Some non-standard VGA cards, like graphics accelerators or MPEG video cards, may not show colors properly.
Onboard SCSI BIOS [Auto] [Auto] allows the motherboard BIOS to detect whether you have a Adaptec SCSI controller. If the SCSI controller is detected, the SCSI BIOS will be enabled. If no SCSI controller is detected, the onboard SCSI BIOS will be disabled. Setting to [Disabled] deactivates the onboard SCSI BIOS so that the BIOS on an add-on SCSI card can be used. If your SCSI card does not have a BIOS, the SCSI card will not function.
4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled], the power management features do not function regardless of the other settings on this menu.
Video Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] Video Off Method [DPMS OFF] This field defines the video off features. The Display Power Management System (DPMS) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen. Use this for monitors without power management or “green” features.
4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configuration options: [Disabled] [Enabled] [Previous State] Wake/Power Up On Ext.
Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Automatic Power Up [Disabled] This allows an unattended or automatic system power up.
4.5.2 Hardware Monitor MB Temperature [xxxC/xxxF] CPU1 Temperature [xxxC/xxxF] CPU2 Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary. CPU1 Fan Speed [xxxxRPM] CPU2 Fan Speed [xxxxRPM] The onboard hardware monitor is able to detect the CPU fan speeds in rotations per minute (RPM). The presence of the fans is automatically detected.
4.6 Boot Menu The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1.01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards. The IPL devices are classified into three categories: 1. BIOS Aware IPL Devices (BAID) 2. PnP devices, includes Boot Connection Vector (BCV) and Bootstrap Entry Vector (BEV) devices 3.
2nd Boot : (BCV) [None] This field allows you to select a Boot Connection Vector (BCV) device to boot from. BCV devices include SCSI controllers or SCSI cards, RAID cards, and other devices on add-on cards with option ROM that hooks INT 13 to BIOS. Some SCSI RAID cards hook INT19 to BIOS. If you use these cards, you should enable INT 19 after installing the card. Otherwise, you cannot enter the RAID card BIOS. The BCV devices present in the system will appear as options for this field.
MPS 1.4 Support [Enabled] This field allows you to enable or disable the MultiProcessor Specification 1.4 support. Configuration options: [Disabled] [Enabled] Quick Power On Self Test [Enabled] This field speeds up the Power-On-Self Test (POST) routine by skipping retesting a second, third, and fourth time. Configuration options: [Disabled] [Enabled] Boot Up Floppy Seek [Enabled] When enabled, the BIOS will seek the floppy disk drive to determine whether the drive has 40 or 80 tracks.
4.7 Server Menu DRAM Hot Spare Memory [Disabled] This field allows you to allocate rows of SDRAM for hot spare. Configuration options: [Disabled] [1 row] [2 rows] [3 rows] Remote Console [Disabled] This field allows the text mode VGA display to be sent out to VT100 terminal through COM1. This function is effective at BIOS POST and DOS environment. Configuration options: [Disabled] [Enabled] [POST Only] Event Log Viewer Pressing on this item gives you a sub-menu.
4.8 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Pressing does not immediately exit this menu. Select one of the options from this menu or from the legend bar to exit. Exit Saving Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM.
Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select [Yes] to load default values. Select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears.
Chapter 5 This chapter tells how to install SCSI, LAN, and VGA drivers under various operating systems.
Chapter summary 5.1 Support CD contents ..................................... 5-1 5.2 Microsoft Windows NT Server 4.0 ................ 5-3 5.3 Microsoft Windows 2000 Server ................. 5-13 5.4 Microsoft Windows XP Professional .......... 5-25 5.5 Novell NetWare Server................................. 5-31 5.6 SCO OpenServer 5.0.6a ............................... 5-36 5.7 SCO UnixWare Server.................................. 5-44 5.8 Linux RedHat 7.3/8.0 ................................
5.1 Support CD contents The support CD that came with the motherboard contains useful software and several utility drivers that enhance the motherboard features. To begin using the support CD, simply insert the CD into your CD-ROM drive. The CD automatically displays the welcome screen and the installation menus if Autorun is enabled in your computer. If Autorun is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder.
5.1.3 Utilities This screen displays the available system utilities that you can install. 5.1.4 Contact This screen displays the ASUS worldwide contact information.
5.2 Microsoft® Windows® NT Server 4.0 5.2.1 LSI® SCSI Driver Installation Windows NT 4.0 does not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows NT 4.0 installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the following path: \Drivers\SCSI\FUSION-MPT\Windows\1.08.022\WINNT This procedure installs the SYMMPI.SYS driver onto a new or existing Windows NT system.
B1. CD-ROM Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute the drivers (web or CDROM), you will create a driver diskette. IMPORTANT: Read Steps 2 and 3 before performing the instructions contained within these steps. 2. Start the Windows NT 4.0 installation by booting from the Windows NT CD-ROM: The system BIOS must support booting from a CD-ROM. BIOS settings may need to be changed to allow CD-ROM booting.
B2. Boot Floppy Disk Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute drivers (web or CDROM), you will create a driver diskette. IMPORTANT: Read Step 2 before performing the instructions contained within this step. 2. Start the Windows NT 4.0 installation by booting from the Microsoft Setup floppy diskette. Press Enter when the Welcome to Setup screen appears. The Windows NT 4.
C. Existing System Installation To install the SYMMPI.SYS miniport driver, follow these steps: 1. Boot Windows NT 4.0 and log on as Administrator. 2. Click on the Start button. Move to Settings-->Control Panel and click. 3. Double click on SCSI Adapters. 4. Click on the Drivers tab. 5. Click Add. A list of installed adapters is displayed. 6. Click the Have Disk button. When prompted, insert the Windows NT Driver Diskette. 7. Enter or type the path to copy manufacturer’s files from A:\. Select OK.
5.2.2 Intel® LAN Driver Installation A. Preparing the Intel LAN Driver Disk Windows NT 4.0 does not have the drivers for the Intel 82551QM/ 82540EM/82544GC LAN controllers. Before installing Windows NT 4.0, copy the LAN drivers from the support CD into a floppy disk. Prepare one blank formatted high density floppy disk before proceeding. 1. 2. Insert the support CD into the CD-ROM drive. Run the utility from the following path: \Drivers\LAN\MAKEDISK\dcreate.exe 3.
5. 6. Insert the floppy disk into the floppy disk drive when prompted. Follow the screen instructions to complete the process. B. New System Installation 1. 2. 5-8 Double-click the Network icon in the Control Panel to display the Network Setup Wizard. When the Installing Windows NT Networking screen appears, press Next to display the following screen.
3. 4. Check the Wired to the Network box, then click Next. On the screen that appears, click the button Select from list... to display the Select Network Adapter window. 5. 6. Insert the LAN driver disk that you created, then click Have Disk... Type A:\ in the dialog box that appears, then click OK. The following screen lists the Intel LAN adapters that you can install. 7. Select Intel(R) PRO/100 Family Adapter, then click OK. Follow the succeeding screen instructions.
8. When done, the following screen appears showing the Intel(R) PRO/100 Family Adapter in the list. 9. Click Select from list..., then click Have Disk... 10. Type A:\ in the dialog box, then click OK. 11. In the following screen, select Intel(R) PRO/1000 Family Adapter, then click OK. Follow the succeeding screen instructions. 12. When done, the following screen appears showing the Intel(R) PRO/1000 Family Adapter in the list. 13.
C. Existing System Installation 1. 2. 4. Double-click the Network icon in the Control Panel. Select the Adapter tab, then click Add. A list of adapters appears. Do not select an adapter from the list. Instead, insert the LAN driver disk that you created from the support CD. Refer to the section “A. Preparing the Intel LAN Driver Disk” if you have not yet created the LAN driver disk. 5. Follow steps 5 to 13 in the section “B. New System Installation” to install the required LAN drivers.
5.2.3 ATI® Rage XL Display Driver Installation 1. 2. Insert the support CD into your CD-ROM drive. If Autorun in enabled in your computer, the following screen appears. Click on ATI Rage XL Display Driver to install the driver. If Autorun is disabled, install the display driver from the following path: \Drivers\ATI\Nt40\Setup.exe 3. 5-12 Follow the screen instructions to complete the installation.
5.3 Microsoft® Windows® 2000 Server 5.3.1 LSI® SCSI Driver Installation Windows 2000 Server does not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows 2000 Server installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the following path: \Drivers\SCSI\FUSION-MPT\Windows\1.08.22\Win2000 This procedure installs the SYMMPI.SYS driver onto a new or existing Windows 2000 Server system.
B1. CD-ROM Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute the drivers (web or CDROM), you will create a driver diskette. IMPORTANT: Read Steps 2 and 3 before performing the instructions contained within these steps. 2. Start the Windows 2000 Server installation by booting from the Windows 2000 Server CD-ROM. The system BIOS must support booting from a CD-ROM.
B2. Boot Floppy Disk Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute drivers (web or CDROM), you will create a driver diskette. IMPORTANT: Read Step 2 before performing the instructions contained within this step. 2. Start the Windows 2000 installation by booting from the Microsoft Setup floppy diskette. Press Enter when the Welcome to Setup screen appears. The Windows 2000 Workstation Setup window appears next.
C. Existing System Installation To install the SYMMPI.SYS miniport driver, follow these steps: 1. Boot Windows 2000 Server and log on as Administrator. 2. Click on the Start button. Move to Settings and click on Control Panel. 3. Double click on SCSI an RAID controllers to display the following window. 4. Click on the Drivers tab. 5. Click Add. A list of installed adapters is displayed. 6. Click the Have Disk button. When prompted, insert the Windows NT Driver Diskette. 7.
14. After rebooting, check the installed SCSI driver from the Computer Management window. 15. Highlight the LSI Logic 1020/1030 Ultra320 SCSI Adapter, click the right mouse button, and select Properties to display the following.
16. Click Driver Details to display a list of files related to the SCSI driver.
5.3.2 Intel® LAN Driver Installation You may install the Intel 82551QM/82540EM/82544GC LAN drivers directly from the support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A. Preparing the Intel LAN Driver Disk.” A. Preparing the Intel LAN Driver Disk Prepare one blank formatted high density floppy disk before proceeding. 1. 2. Insert the support CD into the CD-ROM drive.
5. 6. Insert the floppy disk into the floppy disk drive when prompted. Follow the screen instructions to complete the process. B. Update Driver on an Existing System Installation You may update the LAN driver directly from the support CD. 1. 2. 5-20 Insert the support CD into the CD-ROM drive. On the screen that appears, click on Intel PRO/100 LAN Driver, then on the item Install Base Driver. Follow the screen instructions to complete the driver update.
When done, your Computer Management window shows the installed LAN adapters. 3. Highlight the Intel(R) 82540EM-based Network Connection, click the right mouse button, and select Properties to display the following. 4. Click Driver Details to display a list of the files related to the Intel 82540EM LAN driver.
5. 5-22 Highlight the Intel(R) 82544GC-based Network Connection, click the right mouse button, and select Properties to display the following.
6. Click Driver Details to display a list of the files related to the Intel 82544GC LAN driver. You may also update the LAN drivers from the LAN Driver Disk if you created one. Follow these steps to update from the LAN driver disk. 1. 2. 3. Boot Windows 2000 system and log on as Administrator. Click on the Start button. Select Settings, then Control Panel. Double-click the System icon in the Control Panel. Select the Hardware tab to display the following screen. 4.
5.3.3 ATI® Rage XL Display Driver Installation Windows 2000 system can automatically recognize the ATI RAGE XL PCI driver during system installation. You do not need to load any driver for supporting the onboard ATI RAGE XL graphics controller chipset. 5.3.4 Enabling ATA100 Feature in Windows® 2000 To enable the ATA100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2 or later.
5.4 Microsoft® Windows® XP Professional 5.4.1 LSI® SCSI Driver Installation Windows XP Professional does not have drivers for the new SCSI controllers. You must load the driver manually prior to Windows XP installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the following path: \Drivers\SCSI\FUSION-MPT\Windows\1.08.22\WinXP This procedure installs the SYMMPI.SYS driver onto a new or existing Windows XP system.
B1. CD-ROM Installation 1. Start the Windows XP installation by booting from the Windows XP CD-ROM. The system BIOS must support booting from a CD-ROM. BIOS settings may need to be changed to allow CD-ROM booting. 2. Press the F6 key to install the SYMMPI.SYS driver when the screen displays “Windows Setup.” This must be done or else the new driver will not be recognized. NOTE: Be sure to press the F6 key as any driver loaded later in the installation process is not recognized by Windows XP Setup.
C. Existing System Installation This procedure installs or upgrades the SYMMPI.SYS drivers onto an existing Windows XP system. NOTE: When a LSI Logic SCSI or Fibre Channel adapter is added to an existing system installation, the new adapter is automatically detected at the next reboot. When the Device Driver Wizard appears at boot, click on the Next button and continue at step 8 below. 1. Boot Windows XP and logon as a user that has Administrator privileges. 2.
13. Click STOP Installation to cancel the installation if a nonsigned driver is not desired. - or Click Continue Anyway to continue the installation. The system will load the driver from the Windows XP driver diskette. A message box may display indicating that the target (existing) driver is newer than the source (upgrade) driver. 14. Click No to cancel the driver upgrade at this point. - or Click Yes to continue the installation. The system copies the driver to the system disk.
5.4.2 Intel® LAN Driver Installation For Windows XP Professional users, we recommended that you use the Intel 82551QM/82540EM/82544GC driver from the support CD. A. Preparing the Intel LAN Driver Disk 1. 2. Insert the support CD into the CD-ROM drive. Run the utility from the following path: \Drivers\LAN\MAKEDISK\dcreate.exe 3. In the following screen, click on Make Driver Disk. 4. The next screen allows you to select an operating system to install the driver. Select Windows XP/64 (Gigabit).
5. 6. 5-30 Follow the succeeding installation instructions. When done, the following screen appears. Click Finish to complete the installation.
5.5 Novell® NetWare® Server 5.5.1 LSI® SCSI Driver Installation A single driver (*HAM) is provided for the Novell NetWare 5.1/6.0 environments. This document explains how to install and use the SDMS NWPA SCSI Host Adapter Module (HAM) driver for NetWare. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the following path: \Drivers\SCSI\FUSION-MPT\Netware\3.00.000\ Copy all the drivers into a diskette and it will be used for the NetWare system installation.
3. 4. 5. 6. 5-32 Next the system prompts the user with the available command line options to load the driver. A description of each option appears in the box at the bottom of the installation screen. A more detailed description is given in the section titled Command Line Options. Modify any option values as needed. Load a separate instance of the driver for every LSI Logic controller SCSI channel or host adapter present in the system. When prompted for a slot number, accept the slot numbers displayed.
5.5.2 Intel® LAN Driver Installation You may install the Intel 82551QM/82540EM/82544GC LAN drivers directly from the support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A. Preparing the Intel LAN Driver Disk.” A. Preparing the Intel LAN Driver Disk Prepare one blank formatted high density floppy disk before proceeding. 1. 2. Insert the support CD into the CD-ROM drive.
5. 6. Insert the floppy disk into the floppy disk drive when prompted. Follow the screen instructions to complete the process. B. NetWare 5.1/6.0 Installations 1. 2. 3. 4. 5. 6. 5-34 From the NetWare console, type NWCONFIG or Load Install and press . From the Configuration Options screen, choose Driver options and press . Choose Configure network drivers and press . If any drivers are already loaded, a list of them appears. Choose Load an additional driver and press .
7. The driver name is displayed: Intel(R) PRO PCI adapter. Press to select it. 8. A prompt appears asking if you want to copy the driver. Select Yes and press . 9. The next screen asks for parameters for loading the driver. To modify any driver parameters or protocols, highlight Select/Modify driver parameters and protocols and press . If you have multiple adapters, enter the slot number for the adapter you are currently configuring.
5.6 SCO OpenServer 5.0.6a 5.6.1 LSI® SCSI Driver Installation A. Building the SCO OpenServer BTLD Diskette To create a BTLD diskette for SCO OpenServer system, copy the raw dd image file onto a 1.44MB floppy disk. This process is dependent upon the operating system that you are using to create this diskette. See the instructions below for UNIX System and DOS System Users. Locate the SCSI files in the following path in the support CD: \Drivers\SCSI\Fusion-MPT\SCO\1.03.
B. New System Installation This procedure installs SCO UNIX onto a hard disk drive. This installation is necessary to build a new UNIX kernel that includes your SDMS driver. During installation, you are given the option of retaining current partitions on the root hard disk. For instance, you could have a DOS partition or a user UNIX partition already established on the drive. For more details on UNIX installation, refer to the SCO OpenServer Handbook. 1. 2. 3.
C. Existing System Installation This procedure assumes SCO UNIX is already installed on a hard disk drive. This installation is necessary to build a new UNIX kernel that includes the proper LSI host adapter driver. The basic steps for accomplishing this are outlined below. For more details on UNIX installation, refer to the SCO UNIX System Administrator’s Reference Manual. The SCO OpenServer 5 system automatically creates a file unix.safe during installation.
7. To activate the new kernel, you must reboot the system. At the command prompt, type: reboot Press Enter. C2. Adding a SCSI Disk Drive NOTE: If you are not adding a SCSI or Fibre Channel disk drive to this system, go to step 4. 1. At the command prompt, type: mkdev hd Press Enter. 2. The system prompts for the identifier of the host adapter that supports this device. If the default is correct, press Enter. If the default is not correct, type: lsil Press Enter. 3.
7. 8. The system prompts you to update the Configuration file. Type y and press Enter if the displayed values are correct. Type n if the values are incorrect, and retry from step 3d. A prompt appears to create a new kernel. Type y if this is the last device to be added, or type n if additional devices are to be added. Go to step 6, "Rebuilding the Kernel," if you replied y; return to step 3 if you replied n. C3. Adding a Tape Drive NOTE: If you are not adding a tape drive to this system, go to step 5. 1.
7. With SCO OpenServer 5.0.6a, the system prompts for the bus number of the tape drive. Since LSI Logic host adapters support only one bus per adapter, press Enter to get the default of zero, or type 0 (zero) and press Enter. 8. The system prompts for the ID of the tape drive. Type the ID number of the tape drive and press Enter. 9. The system prompts for the LUN of the tape drive. Type 0 (zero) and press Enter. The system then prompts to update the Configuration file. Type y and press Enter. 10.
5. The system prompts for the host adapter that supports the CD-ROM drive. Type the correct host adapter number and press Enter. If an additional LSI Logic host adapter is being added to the SCO UNIX kernel, the system may prompt if you want to update the link-kit (add another host adapter). Type y and press Enter. If you entered the host adapter number incorrectly, type n, and press Enter. The system then prompts for the host adapter identifier of the preceding step. 6. With SCO OpenServer 5.0.
C5. Rebuilding the Kernel 1. To rebuild the kernel, type: /etc/conf/cf.d/link_unix 2. The system displays will prompt for responses to these messages: a. Do you want this kernel to boot by default (y/n)? Type: y Press Enter. The system backs up the old kernel. b. Do you want the kernel environment rebuilt (y/n)? Type: y Press Enter. 3. To activate the new kernel, you must reboot the system. Type the command: reboot Press Enter. 4. 5.
5.7 SCO UnixWare Server 5.7.1 LSI® SCSI Driver Installation A. Building the LSI Logic Fusion-MPT™ mpt Driver HBA Diskette This is the guide to create an HBA driver diskette for the the Caldera UnixWare 7 and Open Unix 8 Operating Systems. Both of these operating systems will hereafter be referred to as “UnixWare.” To create an mpt HBA diskette for use with UnixWare, you must copy the raw dd image file onto a 1.44 Mbyte diskette.
2. 3. The dd image is located in the zipped file you downloaded from the LSI Logic web site. RAWRITE3.COM is included within the zipped file you downloaded from the LSI Logic web site. After the image has been copied to a 3.5 diskette, use this HBA diskette for UnixWare installations as instructed. B. New System Installation 1. 2. 3. Boot the computer using the installation diskettes or the installation CDROMs delivered in the UnixWare Operating System media kit. Follow the instructions on the screen.
5. Select the mpt package. The mpt driver on this diskette is then loaded onto the system. The system will again prompt you to load a driver even if loading was successful. 6. 7. Type q (quit) and press Enter. Verify that the driver is now loaded successfully by typing: pkginfo mpt 8. The package information should read: system mpt LSI Logic IHV HBA After the mpt package is loaded, a message may appear that indicates a system reboot is necessary. 9.
5.7.2 Intel® LAN Driver Installation SCO UnixWare 7.1.1 system can correctly recognize Intel 82551QM/ 82540EM/82544GC network controller during installation. You don’t need to load or modify the network driver for the onboard LAN device.
5.8 Linux RedHat 7.3/8.0 5.8.1 LSI® SCSI Driver Installation The The Fusion-MPT driver is a bundled boot controller for RedHat 7.3/ 8.0. You may install to a disk attached to the controller with no additional media. For more information on the LSI 53C1030 SCSI controller, refer to the following path in the support CD: \Drivers\SCSI\FUSION-MPT\Linux\2.03.00\mptlinux.txt 5.8.2 Intel® LAN Driver Installation Linux RedHat 7.3/8.
