Quick Installation Guide For Network Attached Storage Ver.2.3.
ASUSTOR NAS Quick Installation Guide Table of Contents Notices.................................................................................................................... 3 Safety Precautions ..................................................................................................... 4 1. Package Contents ............................................................................................ 5 2. Optional Accessories .................................................................
ASUSTOR NAS Quick Installation Guide Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
ASUSTOR NAS Quick Installation Guide Safety Precautions The following safety precautions will increase the life of the NAS. Follow all precautions and instructions. Electrical safety • Unplug this product from the power source before cleaning. • Use only the bundled power adapter. Using other power adapters may damage your device. • Ensure that you plug the power adapter to the correct power input rating. Check the label on the power adapter for the power rating.
ASUSTOR NAS Quick Installation Guide 1. Package Contents Applicable Models: AS5002T, AS5004T, AS5008T, AS5010T, AS5102T, AS5104T, AS5108T and AS5110T. Contents AS5002T AS5102T AS5004T AS5104T 1 1 1 1 1 1 1 1 2 2 2 2 8 8 16 16 8 8 16 16 1 1 1 1 1 1 1 1 NAS device Power cord Adapter RJ45 network cable Screws for use with 3.5” HDD Screws for use with 2.
ASUSTOR NAS Quick Installation Guide Contents AS5008T AS5108T AS5010T AS5110T 1 1 1 1 2 2 2 2 32 32 40 40 32 32 40 40 1 1 1 1 1 1 1 1 NAS device Power cord RJ45 network cable Screws for use with 3.5” HDD Screws for use with 2.
ASUSTOR NAS Quick Installation Guide 2. Optional Accessories The items below may be purchased from local dealers and the ASUSTOR Accessories Store (http://shop.asustor.com). Other items such as HDMI cables (2M recommended), wireless RF keyboards, mice and remote controls along with Bluetooth keyboards and mice are purchased separately.
ASUSTOR NAS Quick Installation Guide 3. Hardware Installation Guide All data stored on the hard disk(s) will be erased and CANNOT be recovered. Please back up all important data before initializing the system. 3.1 Hard Disk Installation • Press the button on the lower portion of the hard disk tray to release the latch. • Using the latch, gently pull the disk tray out of the disk bay. • Mount the hard disk to the disk tray o 3.
ASUSTOR NAS Quick Installation Guide o 2.5-inch hard disks and SSD hard disks: Place the hard disk into the area of the disk tray outlined in red (see picture below). Make sure that the mounting holes on the bottom of the hard disk and disk tray are lined up. Secure the drive with four screws. • Slide the disk tray onto the rails of the disk bay. Using the latch, gently push the disk tray all the way into the disk bay. Secure the disk tray in place by pushing down on the latch.
ASUSTOR NAS Quick Installation Guide 3.2 Connecting and Powering on the NAS • Connect the NAS to its power supply. • Connect the NAS to your router, switch or hub using an Ethernet cable. • Press and hold down the power button for 1 – 2 seconds until the blue power LED indicator is lit. This indicates that the NAS is now powered on. While the NAS is being powered on, the green system status LED indicator will flash and the blue network LED indicator will be lit as well.
ASUSTOR NAS Quick Installation Guide 3.3 Upgrading System Memory 3.3.1 Notes and Precautions All AS50 and AS51 Series NAS devices support up to 8GB of memory. Before adding or removing memory modules, please read the following precautions thoroughly. • Your NAS and memory modules use high precision components and electronic connector technology.
ASUSTOR NAS Quick Installation Guide 3.3.2 • Parts and Tools Needed Phillips head screwdriver 3.3.3 Removing the Cover • Shutdown the NAS by selecting [Shut down] from the ADM User Menu. • Disconnect all cables and devices connected to the NAS including the power cord. • Use a screwdriver to loosen the three screws found on the rear of the NAS as shown in the illustration.
ASUSTOR NAS Quick Installation Guide • Grip the cover from both sides with two hands and then gently push it back to remove it from the chassis. 3.3.4 Installing Memory Note: When installing a single memory module, please ensure that it is the same size as the builtin memory module (1GB/2GB). When installing two memory modules, please ensure that they are the same size and ideally use the same type of RAM for both memory slots. The maximum supported memory is 8GB combined.
ASUSTOR NAS Quick Installation Guide • Using two fingers, carefully push down and then back on the memory module until it clicks into place. You should be able to hear an audible “click”. To install the second memory module, continue with the steps outlined below. • Locate the slot for the built-in memory as shown in the graphic below. • Release the ejector clips by gently pulling them out to the sides and then remove the built-in memory module.
ASUSTOR NAS Quick Installation Guide • When inserting the memory module into the empty slot, please make sure to align the notches on the module with the notches in the slot. Diagonally slide in the memory module (as shown in the illustration) making sure that the memory module’s connectors are fully inserted into the slot. Using two fingers, carefully push down and then back on the memory module until it clicks into place. You should be able to hear an audible “click”. 3.3.
ASUSTOR NAS Quick Installation Guide 4. Software Installation Guide There are 3 different installation methods that you can choose from. Please select the method most suitable for you. If you do not have a CD drive, you can go to the download section of the ASUSTOR website (http://www.asustor.com/service/downloads) to download the latest software. 4.1 CD Installation 4.1.1 Windows Users • Insert the installation CD into your computer’s CD drive and then select “Start” from the autorun CD-menu.
ASUSTOR NAS Quick Installation Guide 4.1.2 Mac Users • Insert the installation CD into your computer’s CD drive and then select “Quick Install” from the autorun CD-menu. • The installation wizard will install ASUSTOR Control Center onto your computer. At this time you can also choose whether or not you want to install Download Assistant. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for ASUSTOR NAS devices.
ASUSTOR NAS Quick Installation Guide 4.3 Installation Using the LCD Display • The LCD display will ask you whether or not you want initialize the NAS once it has detected that the NAS has not yet started to initialize. • Please use the "↵” button found on the right side of the LCD display to confirm that you want to initialize the NAS. The system will now start the initialization process. • Initialization is complete when the NAS’s IP address is shown on the LCD display.
ASUSTOR NAS Quick Installation Guide 5. Appendix 5.1 LED Indicators 1. Power LED Indicator 2. System Status LED Indicator 3. Network LED Indicator 4. USB LED Indicator 5. Hard Disk LED Indicator *For AS5008T, AS5108T, AS5010T and AS5110T models: When Ethernet cables are connected to [Ethernet Port 1] and [Ethernet Port 2] on the rear panel of the NAS, the first network LED indicator on the front of the NAS will become steadily lit.
ASUSTOR NAS Quick Installation Guide 5.2 Rear Panel 1. S/PDIF Port 2. HDMI Port 3. eSATA Port 4. RJ45 & USB 2.0 Port 5. RJ45 & USB 3.0 Port 6. Reset Button 7. DC Input 8. K-lock 9. System Fan 5.3 Rating Label 1. Model Name 2. Power Supply 3.
ASUSTOR NAS Quick Installation Guide 5.4 Troubleshooting Q: Why can’t I detect my ASUSTOR NAS using ASUSTOR Control Center? A: If you are having trouble detecting your NAS using ASUSTOR Control Center, please do the following: 1. Please check your network connection: a. Make sure that your computer and your NAS are part of the same local area network. b. Check to see if the network LED indicator is lit.
ASUSTOR NAS Quick Installation Guide b. Click on [Change adapter settings] in the left hand panel. c. Right-click on [Local Area Connection] and select [Properties].
ASUSTOR NAS Quick Installation Guide d. Under the [Networking] tab select [Internet Protocol Version 4 (TCP/IPv4)] and click on [Properties]. e. Under the [General] tab select the [Use the following IP address] radio button. Set the [IP address] to 169.254.1.1 and the [Subnet mask] to 255.255.0.0 and then click on [OK]. f. Open up ASUSTOR Control Center to scan for your NAS. 4.
