D I S A S S E M B L Y 3 P R O C E D U R E Chapter Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. A SUS A3000N Series Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs.
D I S A S S E M B L Y B A T T E R Y P R O C E D U R E Battery module The illustration below shows how to remove the battery module. B A T T E R Y M O D U L E R E M O V A L Removing Battery Module 1. Turn over the notebook. 2. Slide the battery latch (No.1) to unlock. 1 3. Firmly slide the other latch (No.2) to the top and remove the battery.
D I S A S S E M B L Y H D D M O D U L E P R O C E D U R E HDD Module The illustrations below show how to remove the HDD module from the notebook. H D D M O D U L E R E M O V A L Removing HDD Module 1. Release 1 screw (No.1) [M2*4L, (K) B-NI, NY]] from the HDD cover. 1 2. Lift the HDD cover away. 3. Pull out the hard drive and lift the hard drive away by 2 hands.
D I S A S S E M B L Y H D D M O D U L E D I S A S S E M B L Y P R O C E D U R E Disassembling HDD Module Remove 2 screws here (No.2, No.3) [M3 * 3L (K) B-NI] and 2 screws (No.4, No.5) [M3 * 3 L (K) B-NI] on the other side to separate HDD from HDD housing. 4 5 2 3 *Please do not touch inside of the HDD module.
D I S A S S E M B L Y M E M O R Y M O D U L E M E M O R Y R E M O V A L P R O C E D U R E Memory Module The A3000N Series Notebook comes standard with one SO-DIMM in SO-DIMM socket. There is another expansion SO-DIMM socket for you to upgrade the total memory up to 1024MB with two 512MB SO-DIMM. Removing Memory module 1. Remove 2 screws on DDR Door (No.1, No.2) [M2*3L(K, D3.4) W-NI NY] 1 2 2. Lift the DDR Door away 3. Open the 2 latches aside (No.
D I S A S S E M B L Y W I R E L E S S L A N P R O C E D U R E Wireless LAN Module The illustration below shows how to remove the Wireless LAN module. Removing Wireless LAN module W I R E L E S S 1. L A N Remove 2 Antenna cables from Wireless LAN Module. (No.1, No.2) (White cable: AUX, Black cable: MAIN) R E M O V A L 1 2.
D I S A S S E M B L Y C P U P R O C E D U R E CPU Module The illustrations below show how to remove the CPU module from the notebook. C P U R E M O V A L Removing CPU 1. Remove 2 screws on the Thermal Door, (No.1, No.2) [M2*4L, (K) B-NI, NY]. 2 2. 1 Lift the Thermal Door away.
D I S A S S E M B L Y P R O C E D U R E 3. Disconnect the cable on CPU module. 4. Remove the 2 screws aside the CPU fan (No.3, No.4) [M2 * 6L (K, D4.6) (K) BNI, NY]. 3 4 5. Lift the CPU FAN module away.
D I S A S S E M B L Y 6. P R O C E D U R E Remove the 4 screws upon the CPU module (No.5 ~No.8) [M2 * 6L (K, D4.6) (K) B-NI, NY]. 6 8 7 7. 5 Take away the CPU heat sink module gently.
D I S A S S E M B L Y 8. P R O C E D U R E Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU. L O Unlock 9. Squeeze the vacuum handling pump and use it to lift the CPU away. * Don’t touch the die above the CPU.
D I S A S S E M B L Y O D D P R O C E D U R E ODD Module M O D U L E The illustration below shows how to remove the ODD module. O D D 1. Remove 2 screws from the cover (No.1, No.2) [M2 * 4L (K) B-NI, NY]. R E M O V A L 1 2 2. Put the screwdriver (No. 3) here and push the ODD drive out from the NB.
D I S A S S E M B L Y 3. P R O C E D U R E Remove 4 screws (no.4-7) [M2 * 2L (P) W-NI] from ODD bracket.
D I S A S S E M B L Y K E Y B O A R D P R O C E D U R E Keyboard The illustration below shows how to remove the keyboard D I S A S S E M B L Y K E Y B O A R D R E M O V A L Removing Keyboard 1. Remove 2 screws here (No.1, No.2) [M2 * 6L (K, D4.6) (K) B-NI, NY] 1 2 2. Turn over the NB and open the display panel. 3. Push the 3 latches in (No.1, No.2, No.3) with a pair of tweezers or a singleslotted screwdriver and lift the keyboard plate up.
D I S A S S E M B L Y 4. P R O C E D U R E Lay the keyboard down over the Touch Pad module. *Do not remove the keyboard yet. The keyboard cable is still attached. Removing Keyboard Cable C A B L E R E M O V A L 1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1). 2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers. 3. Lock the connector (no. 3) again to avoid possible breakage. 2. Cable out 1. Unlock 3. Lock 1. Unlock 3. Lock 4.
D I S A S S E M B L Y P R O C E D U R E 5. Disconnect the connector of touch pad beneath keyboard.
D I S A S S E M B L Y L C D P R O C E D U R E LCD Module The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel, invert, LCD hinge bracket, hinge cover, LCD front cover and LCD bottom case. Please do not disassemble the individual parts. L C D R E M O V A L Removing LCD Module 1. Close the display panel. 2. Remove 2 screws on the harness cover (No.1, No.2). [M2 * 4L(K) B-NI, NY] 1 2 3. Remove the harness cover. 4. Remove 2 screws here (No.3).
D I S A S S E M B L Y P R O C E D U R E 5. Disconnect the 2 connectors. 6. Open LCD, and remove 2 screws on both ends (No.1, No.2). [M2. * 4L] 1 7. 3 8. 2 Remove 4 screws on both ends (No.3-6). [M2 * 6L] 5 6 Remove the LCD module from system.
D I S A S S E M B L Y L C D D I S - A S S E M B L Y P R O C E D U R E Disassembling LCD Module 1. Remove 5 rubes and 5 screws (No.1 ~ No.5) [M2.5*6L(K) (4.6) B-NI, NY] on the LCD bezel. 4 3 5 2 1 2. Carefully pry the inside edges of the LCD case open on all four edges with your fingers. Then, lift it away from the LCD module.
D I S A S S E M B L Y P R O C E D U R E 3. Disconnect the 2 cables on inverter board. (No.7, No.8). 8 7 4. Remove 4 screws here (no.9-12) [M2.5*6L(K) (4.6) B-NI, NY].
D I S A S S E M B L Y P R O C E D U R E 5. Remove 4 screws (no.13-16) [M2*3L(K) B-NI, NYLOK] to separate the LCD panel from the LCD back cover. 13 14 15 16 6. Remove the panel and the 2 hinge modules from the LCD back cover.
D I S A S S E M B L Y P R O C E D U R E 7. Remove 6 screws (no.17-22) [M2*3L(K) B-NI, NYLOK] on both sides to separate the LCD brackets from the panel. 19 17 18 20 21 22 8. Disconnect the cable on the back of LCD panel.
D I S A S S E M B L Y P R O C E D U R E 9. Tear of the tape and disconnect the cable from CCD module. 10. Remove CCD module.
D I S A S S E M B L Y P R O C E D U R E 11. Tear the tape on aluminum foil and Remove the cable and microphone.
D I S A S S E M B L Y T O P C A S E M O D U L E T O P C A S E M O D U L E P R O C E D U R E Top Case Module The illustrations below show how to disassemble and remove the top case module of the notebook. The module contains the top case itself, touch pad module. Removing Top Case Module 1. Remove 2 screws (no.1, no.2) [M2*4L(K) B-NI] at back side of notebook. R E M O V E 2 1 2. Remove 3 screws here (no.
D I S A S S E M B L Y 3. P R O C E D U R E Remove 5 screws here (no.6-10) [M2*4L]. 10 6 4. 8 9 7 Remove 5 screws here (no.
D I S A S S E M B L Y 5. P R O C E D U R E Lift it up to release the top case. Removing Touch Pad Module T O U C H P A D 1. Remove 6 screws here (No.16-21) [M2 * 3L] M O D U L E R E M O V E 16 17 18 2. 19 20 21 Disconnect the FPC cable and then remove the touchpad module.
D I S A S S E M B L Y M O T H E R B O A R D P R O C E D U R E Motherboard Module The illustrations below show how to disassemble and remove the motherboard module of the notebook. The module contains the motherboard itself, modem card module. M O D E M C A R D R E M O V A L Removing Modem card 1. Remove 2 screws (no.1-2) (M2*2.5L (K) W-NI)on the modem card. 2 1 2. Pull out the modem card from motherboard. 3. Remove the tape and disconnect the cables (no.3) from modem card and motherboard.
D I S A S S E M B L Y M O T H E R B O A R D R E M O V A L P R O C E D U R E Removing Motherboard 1. Disconnect the connector of speaker (no.4) on motherboard. 4 2. Remove 5 screws (no.5-9)（M2*4L）on motherboard.
D I S A S S E M B L Y 3. P R O C E D U R E Lift the motherboard up a little bit and push aside the bottom case, and then separate motherboard module from the bottom case at an angle of 20 degree.
D I S A S S E M B L Y B O T T O M C A S E M O D U L E S P E A K E R S P R O C E D U R E Bottom Case Module The illustrations below show how to disassemble and remove the bottom case module of the notebook. The module contains the bottom case itself and speakers. Removing Speakers 1. Remove the 4 screws (no.1-4)（M2*3L）on both ends. R E M O V A L 1 2 3 4 4. Lift up both speakers and speaker cable away from the bottom case.
