Shower Enclosure Model Number: Please carefully read these instructions before you begin to install the products.
Before you start Thank you for purchasing your Aston shower enclosure. We hope that it will provide you with years of satisfying use and enjoyment. Please read this manual carefully because it contains information and instructions about the proper installation of the unit. If you do not follow certain conditions of installation and maintenance, your warranty may be affected. 1. Inspect boxes for shipping damage.
Detailed Diagram of Shower Door Components Key Key Number Description Qry Number Description QTY 1 Door Stopper 2 12 Bottom Roller Guide Assembly 2 2 Top Rail 1 13 Door Threshold 1 3 Fixed Glass 1 14 Door Threshold End Cap 4 4 Sliding Door 1 15 Door Seal 1 5 Returned Glass Panel 1 16 Door Seal 1 6 Rail End 1 17 Door Seal 1 7 Wall Mount 1 18 Door Handle 1 8 Glass Clamp 1 19 Fixed Glass Bolt Assembly 2 9 Rail Mount Assembly 1 20 Screw Pack 1 1 10 Sliding Door Track Divider 1 21 Screw Pack 2 1 1 Upper Wheel As
Installation Guide Please read and follow the installation instructions and guidelines in this section. Failure to follow the recommended instructions and installation techniques may lead to possible damage to the unit or the surrounding area. This can affect warranty claims. ATTENTION: This unit requires assembly. A minimum of two people are required for assembly, as several of the sections can be large and unstable until assembled.
Reverse Door opening This shower door can be assembled so that the sliding door opens from Left to Right, or Right to Left. The drawings below illustrate the shower door opening from Left to Right. Note the location of the fixed glass panel and return glass panel for the shower door opening from Left to Right.
Measure the distance Install all of the wall material or materials you intend to use before installing the glass clamps and return glass panel, this includes all moisture resistant wall board or rock board, tile, stone or other wall covering. Refer to the drawing above and measure and mark the shower wall and floor for drilling locations to attach glass clamps.
Install the glass clamp and glass 1/77 ASAP Using the appropriate drill bit for your wall and floor surface drill each hole location with a 5/16” diameter drill bit. Install the plastic wall anchors provided into the drilled holes NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. Using screw pack (1) attach the glass clamps (8) to wall and shower floor using M4x40 screws. Screw Pack 1.
Shower Door Installation ( £3 Wait LLL) 1. Measure the width of the shower opening at the top between the fixed glass and the wall. Note this is dimension "X". 2. The following equation is used to determine the length to be cut from the rail in order to fit the shower opening. 3. Measure distance "Y" from the end of Top Rail (2) with per-assembled hardware mark the top rail. NOTE: Do not cut the end of top rail with per-assembled hardware. Only cut the end of top rail opposite the per-assembled hardware. 4.
Mark the Top Rail Location ATTENTION: A minimum of two people are required for the next assembly steps. Reassembly the top rail (2) onto the fixed glass (3) to locate the mounting points on the wall relative to your desired location. Painters tape or masking tape in the general location of the of the final installation will aid in marking the wall and floor. 1. Slide the door stoppers (1) onto each end of the the top rail (2).
2. Position the top rail (2) and fixed glass (3) as shown in figure 2 and connect fixed glass (3) to top rail (2) following the assembly sequence shown in figure 2. Note in figure 2, one door stopper (1) should be positioned between mounting holes in top rail (2) before connecting top rail to fixed glass. NOTE: TOP RAIL IS ATTACHED TO THE INSIDE OF FIXED GLASS. 3. Loosen set screw on rail end assembly (6) and remove wall mount (7) from rail end (6).
Installing the Top Rail Note: The top and bottom set screws in rail end is facing outward. Assemble per drawing. 1. Loosen set screws in rail end (6) and remove from top rail (2). Next install wall mount (7) onto rail end (6) See figure 1-1. Position rail end assembly (6) onto marked location on shower wall and mark pilot hole drilling location.
2. Using the appropriate drill bit for your wall surface drill the hole locations with a 5/16" diameter drill bit. Install the plastic anchors provided into the drilled holes. 3. Remove the wall mount (7) from the rail end (6). Using the hardware from Screw Pack 2, install the wall mount (7) on the wall. 4. Position glass clamp (8) on floor and attach to floor using M4 x 40 screw from screw pack 2. The glass clamp should be positioned so the single hole is facing toward the inside of shower. See figure 7.
Install Wheel Rollers onto the Door Assemble the upper roller assemblies (11) onto sliding door (4) as seen in figure Note: The door handle mounting holes should be positioned to left. The upper roller assemblies (11) will be on the outside of sliding door (4). The sliding door should be to the inside of shower area.
Hanging the Door UPPER ROLLER CAM Bottom Roller Guide ADJUSTMENT Assemblies Rotate the outer edge of roller assembly using the small hex, while holding the large hex wrench in place. S&S End View upper roller ~——assembly (11) top rail (2) bottom roller ~— guide assembly (12) Suspend the sliding door (4) on the top rail (2). Position the bottom edge of sliding glass door (4) into the groove of the sliding door track divider (10).
Install the Door Threshold rm The Door Threshold is used to prevent water from seeping out while bathing. Install the threshold according to these instructions. 1. Measure the distance between the fixed glass (3) and the shower wall. See figure 1 2. Using a hacksaw cut the threshold bar (13) to fit distance measured between the fixed glass and shower wall. Remove any sharp edges or burrs after cutting threshold bar (13). See figure 2 3.
NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. 4. Using the appropriate drill bit for your floor surface drill the hole locations with a 5/16" diameter drill bit. Install the plastic anchors from Screw pack 4 into the drilled holes. Repeat for the other side. See figure 4 5. Add a small amount of silicone sealant to bottom of threshold bar assembly place into position. See figure 5 6.
Installing the door handle Lemma] — Install the door handle (18) using hardware provided. Follow the assembly sequence seen in drawing.
Final sealing Using Bath & Kitchen silicone sealant, seal the fixed glass (3) along bottom edge on shower base, and side edge along shower wall. Next seal around sliding door track divider (10).
Care and Maintenance As with any other luxury item, maintenance and care are critical to the long lasting quality and enjoyment of your shower door and tray. The proper care and maintenance outlined in this section are necessary to ensure the longevity of the unit. Damage caused by not following the care and maintenance guidelines in this section is not covered under the manufacturer's warranty. The glass doors and panels can be cleaned using any commercially available glass cleaner.
Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR ASTON GLOBAL BATHROOM PRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. SHOWER DOOR/SHOWER TRAY Aston Global Inc. Parts-Only Limited Warranty 5 years Warranty for any part in oil rubbed bronze finish is limited to two (2) years. Aston Global, Inc.
THIS WARRANTY DOES NOT COVER: 1. Product installed in buildings other than single family dwelling units. 2. Product installed outdoors or any other non-standard bathroom location. 3. Component parts not manufactured by Aston Global. 4. Workmanship of any installer of Aston Global Product.
Customer is required to provide adequate access the Product for any repair or inspection. Aston Global shall not be liable for expenses or damage which may include but are limited to water damage, removal of any and all common building product such as tile, flooring, wood, sheet rock, plumbing fixtures, concrete board, vanities, bathtubs and toilets or any other custom items. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
ANTON ESCAPE THE EVERYDAY Customer Service 877-424-9699 Aston Global Inc 10480 Brock wood Road Dallas, TX 75238 If further assistance is needed, or you have a question, please visit our web site at: www.astonbath.