Certification Exhibit FCC ID: U4A-SCYPROX5 IC: 6982A-SCYPROX5 FCC Rule Part: 15.209, 15.249 IC Radio Standards Specification: RSS-210 ACS Project Number: 12-0305 Manufacturer: Assa Abloy Model: C2-PA/PK Manual 5015 B.U.
in ar y IN100 im with Aperio™ Technology Pr el Mortise Lock Installation Instructions A8122B 8/12 Copyright 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. These installation instructions include Microsoft® Tags that you can scan to view videos of certain installation steps. The Microsoft Tag mobile app is required to scan the Tags.
Table of Contents 3 4 5 6 7 8 9 1 Warning Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment. ar 2 y Warning . ..................................................................................2 General Description..................................................................3 Specifications...........................................................................3 System Overview..................................
IN100 Mortise Lock General Description 2 The SARGENT® IN100 mortise lock with Aperio™ Technology makes it easy and cost-effective to bring access control to doors. It uses local wireless communication between the lock and an Aperio hub to connect to an access control system, eliminating the greatest cost and inconvenience of traditional access control – the wiring at the door. The IN100 utilizes HID® iCLASS® 13.
IN100 Mortise Lock Parts Breakdown 5 13.56 MHz iCLASS & 125kHz Prox 8 7 1* 3 4 3 6 6 5 2 ar y 1* im in 10 8/050/12 Pr el Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 19 18 17 16 21 20 21 21 19 * Patent pending 15 Tools Required: 15 13 14 4 1-800-810-WIRE • www.sargentlock.
IN100 Mortise Lock Parts Breakdown 13.56 MHz iCLASS & 125kHz Prox (Continued) QTY.
IN100 Mortise Lock 6 Lock Installation 1 Prepare Door A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. LHRB RH RHRB Left Hand Reverse Bevel Hinges Left Open Outward Right Hand Hinges Right Open Inward Right Hand Reverse Bevel Hinges Right Open Outward Fig. 1A in B. Door Preparation ar y LH Left Hand Hinges Left Open Inward Prior to installation, all holes must be free of burrs, debris and sharp edges.
IN100 Mortise Lock 2 How to Change Hand of Lock body A. Reverse Lock Hand 1. Position lock body so the red surface of the locking piece is visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece. 3. Push locking piece toward the back of the lock body and rotate the locking piece 180°. Note: Red indicates locked (outside) side. y B. Reverse Latch Hand 1. Rotate the latchbolt 180°. Locking piece Fig.
IN100 Mortise Lock 4 Weather Conduit Installation (Optional P/N 52-2847) Install weather conduit on NON FIRE-RATED metal exterior doors only (Fig. 4A). 1. Carefully insert the weather conduit into the ribbon cable hole from the outside of the door. 2. Place the O-ring around the weather conduit on the inside and up against the door (Fig. 4B). Inside of Door O-Ring y Fig. 4B 1. Feed the wire harness through the mortise pocket and inside preparation hole as depicted in Fig. 5.
IN100 Mortise Lock 6 Attach Front Plate Outside of Door Attach front plate with (2) flat head screws. y Scan this Microsoft® Tag using your mobile phone to see a video of this installation step. The Microsoft Tag mobile app is required to scan the Tag. Download the free mobile app at http://gettag.mobi Pr el Make certain the lever spindle is properly engaged inside the lock body (Fig 7A). 2. On the inside of the door, insert spindle into square hole of mortise lock (Fig 7B). 3.
IN100 Mortise Lock 8 Install Inside Rose and Inside Lever Assembly 1. Rotate the inside rose first counter clock wise to seat the threads then clockwise to securely tighten. Inside of Door 2. Slide lever handle onto spindle until fully seated. Be sure handle is horizontal and facing the hinge side of the door. Push lever onto spindle so minimum gap is visible. Spindle 3. Tighten the set screw securely with a T20 Torx. Rose 4.
IN100 Mortise Lock Inside of Door 10 Install Thumb Turn 1. Insert thumb turn into preparation hole and engage slot in lock body. 2. Orient mounting plate so screw hole is vertical (aligned with preparation holes). 3. Secure plate with phillips screw provided. 4. Test thumb turn for function by retracting and projecting the deadbolt (7976 and 7977 functions only). Phillips screw ar Fig. 10 in Scan this Microsoft® Tag using your mobile phone to see a video of this installation step.
IN100 Mortise Lock 12 Gasket Installation (Optional P/N 52-1332) Gasket required for exterior doors (not required for fire rating). Figure 12. 1. Place the gasket on the on the reader posts and ensure the shape is aligned with the edge of the reader. Fig. 12 1. Orient the reader so the HID logo is at the bottom and the lens is at the top. 2. Feed the ribbon cable through the door (from out side to inside). 3.
IN100 Mortise Lock 14 Configuring RX Switch Handing Inside of Door 1. Each lever handle has a sensor installed but only the inside lever is utilized for RX sensing. 2. To properly configure the RX functionality, connect the terminals as indicated below: RH or RHRB door handing (blue to blue) LH or LHRB door handing (yellow to blue) 3. Note: Factory default is blue to blue (right hand lock). IMPORTANT: grasp each connector firmly before separating. Do not pull wires apart.
IN100 Mortise Lock 16 Battery Housing Installation Inside of Door 1. Position the DPS and harness below the tabs of the mounting plate. 2. Align the tabs of the battery housing with the tabs of the mounting plate. Push down. 3. Lightly press the lock harness to assemble. 4. Snap battery compartment into position. 8/050/12 im Fig. 16 Pr el Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
IN100 Mortise Lock 18 Inside Cover Installation 1. Assemble cover by hooking top edge on inside mounting plate. 2. Carefully press bottom of cover toward door without pinching any wires. 3. Secure the cover utilizing a 1/8” security Allen wrench. Inside of Door Inside Cover Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IN100 Mortise Lock 8 Operational Check For 7976- and 7978-function mortise locks with cylinders: 1. Insert key into cylinder and rotate. There should be no friction against lock case, wire harness or any other obstructions. 2. Check that the key retracts the latch: the key should rotate freely. 3. Throw the deadbolt (if present): Check that the key retracts both the deadbolt and the latch. 8/050/12 Pr el Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
IN100 Mortise Lock 9 Lock LED Indications 1 Lock Normal Operation LED indication The lock has three LEDs that support an optical scheme with red, yellow and green. The indication scheme is described by the figures below: Card read (configurable) One yellow flash (.25 seconds) Access granted, EAC offline or online One green flash (1 second) Access denied, EAC online One red flash (1 second) Access denied, EAC offline Three red flashes (.
IN100 Mortise Lock 3 Lock Self Test LED Indication After replacing the battery, a Power On Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as is described by the figure below: One red, one green flash (1 second each) Good POST Bad POST One red flash followed by 16 red or green flashes (.5 seconds each) The “Error in lock” indication is also shown instead of the POST flashes if the battery is not accepted as new after a power-on-reset. 10 red flashes.
Pr el im in ar y Notes The global leader in door opening solutions
y ar in im Pr el SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.