Certification Exhibit FCC ID: U4A-SCYPROX3 IC: 6982A-SCYPROX3 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0443.W06.11.A Manufacturer: Assa Abloy Model: S1-PA/PK, S2-PA/PK, TCIP1-M802/M803, TCWI1-M802/M803 Manual(s) 5015 B.U.
v.S2 Profile WiFi Mortise Lock Installation Instructions A7786E 01/11 Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents 1 1 Warning . ..................................................................................2 2 General Description..................................................................3 3 Hardware Specifications..........................................................3 4 Electronic Specifications..........................................................3 5 Installation Wiring Overview....................................................3 6 Lock Wiring.........................
Profile Series v.S2 WiFi Mortise Lock 2 General Description The SARGENT Profile Series v.S2 mortise lock is available with either an HID® 125 kHz prox or 13.56 MHz iCLASS® technology reader. It is designed for applications requiring wireless access control. The v.S2 is a self-contained microprocessor-controlled access control product with non-volatile memory. It is able to utilize the existing wireless LAN (802.11b/g) in order to communicate with the access control system. The v.
8 7 6 (+) 9VDC (RED) (-) (BLACK) AX/DPS NC (PINK) AX/DPS COM (VIOLET) Unused Unused Unused EGND (GREEN) TB1 5 DX NC (GREEN/WHITE) RX COM (WHITE) RX NC (GREEN) DX (WHITE/BLACK) LX NO (RED/YELLOW) LX COM (RED/GREEN Motor B (BLACK) Motor A (RED) E1 4 Ring Terminal From Trim 3 1 1-800-810-WIRE • www.sargentlock.com • A7786E 2 3 4 5 4 6 From Lock Body 2 1 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
16 12 11 9 7 13 1 15 15 14 1-800-810-WIRE • www.sargentlock.com • A7786E Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 7 5 01/29/11 Profile Series v.S2 WiFi Mortise Lock Parts Breakdown 125 kHz Prox and 13.
Profile Series v.S2 WiFi Mortise Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued ITEM Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. QTY.
Profile Series v.S2 WiFi Mortise Lock Installation Instructions Step #1 – Door Preparation A. Verify Hand and Bevel of Door Stand on outside/locked side of door when determining the door hand. LH Left Hand Hinges Left Open Inward LHRB Left Hand Reverse Bevel Hinges Left Open Outward RH Right Hand Hinges Right Open Inward RHRB Right Hand Reverse Bevel Hinges Right Open Outward Fig. 1A B. Door Preparation Prior to installation, all holes must be free of burrs, debris and sharp edges.
Profile Series v.S2 WiFi Mortise Lock Step #2 – How to Change Hand of Lockbody A. Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. 3. Rotate the locking piece 180° until RED surface is on opposite side. Connector Note: Red indicates locked side (outside).
Profile Series v.S2 WiFi Mortise Lock Step #3 – Install Lockbody To install lockbody: 1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lockbody (Fig. 3A). Note: Connectors and wires must be fed through non-cylinder side. 2. The wires from the lockbody exit the inside door prep through the mortise cutout. 3. Loosely secure the lockbody in the door with two #12 x 1-1/4" wood screws or #12-24 x 1/2" machine screws. Note: Do not completely tighten at this time.
Profile Series v.S2 WiFi Mortise Lock Step #5 – Install Gasket (for Exterior Doors) For exterior applications, use weather seal gasket between escutcheon and outside door surface. To apply weatherseal gasket: Gasket 1. Carefully remove the backing from the gasket. (Fig. 5A). 2. Apply gasket to escutcheon: Keypad Ribbon Cable a. Starting in one place, press the adhesive side of the gasket firmly against the escutcheon. b.
Profile Series v.S2 WiFi Mortise Lock Step #7 – Inside Escutcheon Wire Connections Images are shown without gasket. If gasket is necessary, refer to Step #5. Before the controller is attached to the door: Reader Ribbon Cable 1. Attach the reader assembly ribbon cable into the back of the controller assembly (side that faces towards the door when mounted (Fig. 7A). 1 2 2. Attach the antenna to the circuit board in the plastic housing under the controller assembly.
Profile Series v.S2 WiFi Mortise Lock Step #9 – Install Inside Escutcheon 1. Gently fold the excess ribbon connector and ground wire into the top hole, JST connectors and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig. 9A). Inside of Door 2. Insert (2) #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon. Straighten escutcheons and tighten securely.
Profile Series v.S2 WiFi Mortise Lock Step #11 – Install and Secure Cylinder 1. Slide cylinder through the spring and rosette/collar and screw into lockbody, rotating the cylinder clockwise (Fig. 11A). Cylinder should be flush with escutcheon. Outside of Door Note: The 43 cylinder may be used when installing this product with or without a gasket. Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 11B). 2.
Profile Series v.S2 WiFi Mortise Lock Step #13 – Install (or Replace) Batteries IMPORTANT: Batteries are optional if controller is powered by external power supply. 1. To install or replace batteries, first remove the battery cover (if necessary) using the provided security tool (Fig.13A). 2. Unscrew the bottom screw of the battery keeper and remove the battery keeper, being careful not to break the tabs at top that hold it in place (Fig.13B) 3.
Profile Series v.S2 WiFi Mortise Lock Operational Check For 8276 and 8278 Function mortise locks with cylinders: 1. Insert key into cylinder and rotate (There should be no friction against lock case, wire harness or any other obstructions. Refer to Section 7, Step 8 if harness friction exists). 2. The key will retract the latch. Key should rotate freely. 3. If the deadbolt is thrown, the key will retract both the deadbolt and the latch. 4. Inside lever retracts latch and deadbolt (if provided). 5. Use a 13.
SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company.