Certification Exhibit FCC ID: U4A-SCYICLS2 IC: 6982A-SCYICLS2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0071.W06.11.A Manufacturer: Assa Abloy, Inc. Model: P1-IM/IKM Manual 5015 B.U.
PR EL IM IN AR Y P1 A8032D 12/10 Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents Warning . ..................................................................................2 2 General Description..................................................................3 3 Hardware Specifications..........................................................3 4 Electronic Specifications..........................................................3 5 Installation Wiring Overview....................................................3 6 Installation Wiring.......................
Passport 1000 Series P1 PoE Mortise Lock 2 General Description The SARGENT Passport Series v.P1 cylindrical lock is available with either an HID® Prox 125 kHz or 13.56 MHz iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet) providing access control with Magnetic swipe and optional Proximity Reader and/or Keypad, as well as detailed audit capabilitiestechnology as a proven alternative to traditional access control installations. The v.
Passport 1000 Series P1 PoE Mortise Lock 6 Installation Wiring A. PoE Frame harness assembly (From McKinney) B. PoE data hinge (Patent Pending) (From McKinney) Supplied by CI C. PoE Door harness* D. Passport 1000 Online P1 PoE Lock * Order of installation may vary. Refer to appropriate sections for instructions.
Passport 1000 Series P1 PoE Mortise Lock Installation Wiring (Continued) A Frame Harness Installation Components and wire harness supplied by McKinney: Suggested installation. Supplied by CI Cut end / ceiling-side PoE harness: B-Splice Crimp Connector TIA/EIB-568-B Standard Wiring 3 4 5 6 7 8 Pair Number RJ45-M White/Green 5 Blue 4 White/Orange 1 Orange 2 White/Green 3 Green 6 White/Brown White/Brown 7 Brown 8 IN IM 2.
Passport 1000 Series P1 PoE Mortise Lock C PoE Data Hinge Order of installation may vary. Refer to appropriate sections for instructions. Hinge-side harness connectors: • 4-pin male Molex connector • 6-pin male Molex connector with ground wire Lock-side harness connectors: • Ring terminal • (2) 4-pin connectors: • 4-pin Molex connector • 4-pin connector Notes: Connectors go on only one way. They cannot be plugged to incorrect position. • Do not force and do not offset connectors.
Passport 1000 Series P1 PoE Mortise Lock 8 Parts Breakdown P1 PoE Lock with Magnetic Card Swipe With or Without Keypad 10 10 14 13 13 13 12 12 12 11 11 11 10 10 10 10 10 99 9 5 5 Y 3 2 5 4 5 6 7 AR 1 2 1 4 3 6 5 7 5 8 8 Inside IM IN Inside Inside P2 P2 Outside Outside DESCRIPTION 52-0757 Lens (Cliplite) 52-0738 Outside Passport Escutcheon Only (Magnetic Swipe and Keypad) PR 2 PART No.
Passport 1000 Series P1 PoE Mortise Lock Parts Breakdown (Continued) P1 PoE Lock with Magnetic Card Swipe , 125 kHz Prox and Keypad 10 13 11 2 1 2 3 4 6 7 IM IN 1 3 3 5 5 8 5 AR 4 5 3 8 9 10 10 Y 6 7 3 9 10 11 Inside P2 Outside 12/15/10 EL ITEM No. PART No.
Passport 1000 Series P1 PoE Mortise Lock 8 Parts Breakdown Magnetic Card Swipe With 13.56 MHz iCLASS and Keypad 4 9 8 7 Y 6 4 AR 5 4 3 IN 2 Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 4 4 10 ITEM No. PART No.
Passport 1000 Series P1 PoE Mortise Lock 8200 Series Mortise Lock 6 5 4 3 7 IN 14 12/15/10 2 13-0140 3 See catalog 4 DESCRIPTION #41 Cylinder (1-1/8” Minimum Length) Cylinder Compression Spring 1KB-1 Cylinder Rosette See catalog Mortise Lockbody 77-2592 130 KB Thumbturn for Deadbolt Functions Only See catalog Inside Lever Handle See catalog Outside Lever Assembly 8 82-0368 Spindle 9 82-3088 Inside Lever/Knob Adapter Plate Assembly 10 01-1495 #8-32 X 5/8 Machine Screw 11 82-061
Passport 1000 Series P1 PoE Mortise Lock Door Preparation A. Verify Hand and Bevel of Door Left Hand Hinges Left. Open Inward. “LH” Left Hand Reverse Bevel Hinges Left. Open Outward “LHRB” Right Hand Hinges Right. Open Inward. “RH” Y Right Hand Reverse Bevel Hinges Right. Open Outward. “RHRB” AR B.
Passport 1000 Series P1 PoE Mortise Lock Connector 2 How to Change Hand of Lockbody Ring Terminal A. Reverse Lock Hand Red surface of locking piece must face the outside/ locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. 3. Rotate the locking piece 180° until RED surface is on opposite side.
3 Install Lock Body 1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lockbody (Fig. 3A). 2. The wires from the lockbody exit the inside door prep through the mortise pocket (Fig. 3B). 3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws. Must feed the harness first, followed by the lock body. PoE Cables Y Feed wire into mortise slot. AR (2) #12 x 1-1/4” Long Flat Head Wood Screw for Wood Doors Fig.
Passport 1000 Series P1 PoE Mortise Lock 5 Install Inside and Outside Levers 1. Slide the outside lever and spindle assembly through the door and lockbody. 2. Using the inside adapter plate and spindle, secure loosely with (2) #8-32 screws. Note: Position threaded hole on the inside adapter to align with lever hole. 3. Tighten the lockbody screws on edge of door. 4. After the lockbody screws are tightened, tighten both inside adapter screws. 5. Position and attach rose over inside adapter. 6.
Passport 1000 Series P1 PoE Mortise Lock 7 Install Gasket (Optional) Note: Optional, for non-fire rated doors only. For non-fire rated door applications, an optional gasket may be used as a weather seal between the escutcheon and the outside door surface. Gasket Peel off adhesive backing and attach to outside escutcheon. Outside Passport Trim 8 Install Outside Escutcheon and Mounting Plate Assembly AR Y Fig. 7A 1. Insert the mounting posts through holes as shown. 2.
Passport 1000 Series P1 PoE Mortise Lock 9 Install Inside Module Component Assembly Insert bottom of Module Component Assembly first (Fig. 9A), then clip top of Assembly to backplate, verifying both tabs attached securely. Tabs AR Fig. 9A Y Outside of Door IN 10 Attach Connectors Secure the following connectors onto the circuit board (Fig. 10A and 10B): IM 1. Secure the 10-pin lock body assembly connector (e). 2. Secure the 24-pin keypad/card reader connector (d).
Passport 1000 Series P1 PoE Mortise Lock 11 Install Inside Escutcheon 1. Position inside escutcheon as shown (Fig. 11A). Verify that all wires are positioned within the escutcheon to avoid pinching. (2) #8-32 x 1/2” Torx Screws 2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan head screws. 3. Straighten escutcheon and tighten securely. Fig. 11A IM IN AR Y DO NOT OVERTIGHTEN. PR Attach front plate with (2) #8-32 X 1/4” flat head screws (Fig. 12A). (2) #8-32 x 1/4” Flat Head Screws Fig.
Passport 1000 Series P1 PoE Mortise Lock 9 Operational Check IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For units with cylinders, the following checks apply: Insert key into cylinder and rotate: b. The key should retract the latch and the key should rotate freely. c. The key should extend and retract the deadbolt.
Y AR IN IM EL PR SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.