Certification Exhibit FCC ID: U4A-SCYICLS2 IC: 6982A-SCYICLS2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0071.W06.11.A Manufacturer: Assa Abloy, Inc. Model: P2-IM/IKM Manual 5015 B.U.
IN AR Y P2 IM PASSPORT 1000 EL Mortise Lock PR Installation Instructions A8011E 12/10 Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents Warning . ..................................................................................2 2 General Description..................................................................3 3 Hardware Specifications..........................................................3 4 Electronic Specifications..........................................................3 5 Parts Breakdown......................................................................4 6 Installation Instructions............
Passport 1000 Series P2 Mortise Lock 2 General Description The SARGENT Passport Series v.P2 Mortise Lock is available with either an HID® Prox 125 kHz or 13.56 MHz iCLASS® technology reader. Designed specifically for the campus market, the SARGENT Passport 1000 P2 WiFi Mortise Lock is a new breed of electronic lock, providing access control with magnetic swipe and optional Proximity Reader and/or Keypad, as well as detailed audit capabilities.
Passport 1000 Series P2 Mortise Lock 5 Parts Breakdown P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad 10 10 14 13 13 13 12 12 12 11 11 11 10 10 10 10 10 99 9 Y 8 AR 4 3 6 5 7 5 Inside IN 1 2 1 3 2 5 4 7 5 5 6 5 8 IM Inside Inside Outside Outside PART No. DESCRIPTION 52-0757 Lens (Cliplite) 52-0738 Outside Passport Escutcheon Only (Magnetic Swipe and Keypad) PR ITEM No. EL Outside Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company.
Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) P2 WiFi Lock with Magnetic Card Swipe, 125 kHz and Keypad 11 13 3 6 8 5 7 AR 1 5 12 10 Inside Inside Outside IM IN P2 PART No.
Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) P2 WiFi Lock with Magnetic Card Swipe, 13.56 MHz and Keypad 4 9 8 Y 7 AR 6 4 5 4 IN 3 IM 2 12/15/10 PR EL Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 1 6 4 4 10 ITEM No. PART No.
Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) 8200 Series Mortise Lock 6 5 4 3 13 Y 11 12 AR 9 10 7 IN 8 16 17 PART No.
Passport 1000 Series P2 Mortise Lock 6 1 Installation Instructions Door Preparation A. Verify Hand and Bevel of Door B. Verify Product Label Left Hand Reverse Bevel Hinges Left. Open Outward. “LHRB” Right Hand Hinges Right. Open Inward. “RH” AR Left Hand Hinges Left. Open Inward. “LH” Y Stand on outside of locked door when determining door hand. Right Hand Reverse Bevel Hinges Right. Open Outward.
Passport 1000 Series P2 Mortise Lock Connector 2 How to Change Hand of Lockbody Ring Terminal A. Reverse Lock Hand Red surface of locking piece must face the outside/ locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. 3. Rotate the locking piece 180° until RED surface is on opposite side.
Passport 1000 Series P2 Mortise Lock 3 Install Lock Body 1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lockbody (Fig. 3A). 2. The wires from the lockbody exit the inside door prep through the mortise pocket (Fig. 3B). 3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws. Must feed the harness first, followed by the lockbody.
Passport 1000 Series P2 Mortise Lock 5 Install Inside and Outside Levers 1. Slide the outside lever and spindle assembly through the door and lockbody. 2. Using the inside adapter plate and spindle, secure loosely with (2) #8-32 screws. Note: Position threaded hole on the inside adapter to align with lever hole. 3. Tighten the lockbody screws on edge of door. 4. After the lockbody screws are tightened, tighten both inside adapter screws. 5. Position and attach rose over inside adapter. IM Fig.
Passport 1000 Series P2 Mortise Lock 7 Install Gasket (Optinal) Note: Optional, for non-fire rated doors only. For non-fire rated door applications, an optional gasket may be used as a weather seal between the escutcheon and the outside door surface. Gasket Peel off adhesive backing and attach to outside escutcheon. Y Outside Passport Trim 1. Insert the mounting posts through holes as shown. 2. On the inside of the door, position the mounting plate over the indicated holes.
Passport 1000 Series P2 Mortise Lock 9 Install Inside Module Component Assembly Insert bottom of Module Component Assembly first (Fig. 9A), then clip top of Assembly to backplate, verifying both tabs attached securely. Tabs Y Outside of Door AR Fig. 9A IN 10 Attach Connectors Secure the following connectors onto the circuit board (Fig. 10A and 10B): IM 1. Secure the 10-pin lock body assembly connector. 2. Secure the 24-pin keypad/card reader connector. Connectors go on only one way.
Passport 1000 Series P2 Mortise Lock 11 Install Battery/Battery Pack 1. Place (6) “AA” batteries into the compartment being careful to align polarity (- & +) properly. 2. Insert battery pack and click into place, making sure polarity terminals on the battery pack are correctly oriented (Fig. 11A). 12/15/10 IM EL 12 Attach Outside Front Plate 1. Position inside escutcheon as shown (Fig. 12A). Verify that all wires are positioned within the escutcheon to avoid pinching.
1-800-810-WIRE • www.sargentlock.com • A8011E 15 12/15/10 Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IM EL PR IN Y AR Passport 1000 Series P2 Mortise Lock 13 Attach Outside Front Plate Attach front plate with (2) #8-32 X 1/4” flat head screws (Fig. 13A). (2) #8-32 x 1/4” Flat Head Screws Fig.
7 Installation Instructions IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For units with cylinders, the following checks apply: Insert key into cylinder and rotate: b. The key should retract the latch and the key should rotate freely. Y a. There should be no friction against lock case, wire harness, or any other obstructions.