User's Manual

ManualsBrandsASSA ABLOY Hospitality ManualsElectronicsPCBA 7001

1 66 1402 203-5

66 1402 203-1

FCC (Federal Communications Commission) statements

This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) The BLE Module may not cause harmful interference, and

2) The BLE Module must accept any interference received, including interference that may cause undesired operation.

Important note: To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Use only the supplied antenna.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

The concerned end product must be labeled to say ‘Contains FCC ID: Y7V-7001CC1’.

IC (Industry Canada) statements

This device comply with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B. Operation is subject to the following two conditions:

1) The BLE Module may not cause interference, and

2) The BLE Module must accept any interference, including interference that may cause undesired operation of the device.

Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters are exempted from Routine Evaluation

Limits – SAR Evaluation in accordance with RSS-102 section 2.5.1.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This BLE Module

‘IC: 9514A-7001CC1’ has been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included

in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Name/Model

Gain

Impedance

Inverted F-antenna

3.0 dBi

50 ohm

The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. The concerned end product must be labeled to say ‘Contains IC: 9514A-7001CC1’.

Déclarations d’Industry Canada

Cet équipement est conforme aux normes d’exemption de licence RSS d’Industry Canada CAN ICES-3 (B)/NMB-3(B) B. Son utilisation est soumise aux deux conditions suivantes:

1) Le module BLE ne doit pas provoquer d’interférence, et

2) Le module BLE doit accepter toute interférence, y compris des interférences susceptibles de provoquer un fonctionnement indésirable de l’équipement.

Remarque importante: Pour respecter les limites d’exposition aux radiofréquences d’Industry Canada pour le grand public, les antennes utilisées pour ces émetteurs-transmetteurs sont exemptées des limites

d’évaluation de routine – évaluation SAR, conformément à la norme RSS-102 section 2.5.1.

Conformément aux réglementations d’Industry Canada, cet émetteur radio peut uniquement fonctionner à l’aide d’une antenne dont le type et le gain maximal (ou minimal) pour ces émetteurs-transmetteurs sont

approuvés par Industry Canada. Pour réduire le risque d'interférence éventuelle pour les autres utilisateurs, le type et le gain de l'antenne doivent être choisis de manière à ce que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne soit pas supérieure à la puissance nécessaire à une bonne communication. Ce module BLE ‘IC: 9514A-7001CC1’ a été approuvé par Industry Canada pour une utilisation avec les types

d’antenne indiqués ci-dessous avec le gain maximum autorisé indiqué et l’impédance d’antenne requise. Il est strictement interdit d’utiliser avec cet appareil un type d’antenne ne figurant pas dans cette liste ou ayant

un gain supérieur au gain maximum indiqué pour ce type.

Appellation/Modèle

Gain

Impédance

Antenne F inversée

3.0 dBi

50 ohm

Le terme « IC » devant le numéro de certification de l’équipement signifie seulement que les spécifications techniques d’Industry Canada ont été respectées. Le produit final concerné doit porter une étiquette avec la

mention: ‘Contient IC: 9514A-7001CC1’.

Quick installation guideline – Signature lock with housing BLE

Summary of content (5 pages)

PAGE 1
Quick installation guideline – Signature lock with housing BLE FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) The BLE Module may not cause harmful interference, and 2) The BLE Module must accept any interference received, including interference that may cause undesired operation.
PAGE 2
Introduction With the Mobile Access option set in the Visionline software, the BLE technology (Bluetooth® Low Energy) is used for exchanging data. Instead of using cards for access, mobile keys are used. The guest must have a Bluetooth® telephone which is registered with an Endpoint ID, and an app for opening the door. A 3G RFID Signature lock is upgraded to BLE usage by following the steps in this instruction.
PAGE 3
Procedure Figure 4 Figure 4 1. If the door thickness requires it: exchange the regular spacers on the back of the LCU Signature RFID assy with the screws standoff (item number 4 in Figure 1). 2. Mount the LCU Signature RFID assy (3G) in the housing BLE. Figure 8 6. Mount the BLE module in the housing BLE. Figure 5 3. Thread the cable sleeve onto the 3G RFID LCU reader cable. Figure 6 4. 5.
PAGE 4
11. Use a screwdriver Torx TR20 (or Torx T20) to fasten the mounting frame with two screws on the back of the door. 10. Mount the housing BLE including the LCU Signature RFID assy (3G) on the door; the spacers (or the screws standoff) on the back of the LCU Signature RFID assy (3G) are in step 11 fastened together with the mounting frame (full name mounting frame inside Signature). Figure 11 Note: Make sure to align the mounting frame on both sides before fastening it.
PAGE 5
Figure 16 Figure 18 20. Use the tabs on the sides of the mounting plate to keep the cables in place; see Figure 16. Figure 17 21. Thread the battery cover Signature onto the mounting frame. 22. Use a screwdriver Torx TR20 to fasten the battery cover Signature. ASSA ABLOY Hospitality APAC: e-mail apac.hospitality@assaabloy.com, phone +65 6305 7670 ASSA ABLOY Hospitality North America: e-mail northam.hospitality@assaabloy.com, phone +1 972 907 2273 23.