Quick Installation Guide

2. Installation
Wireless Router
EAI2304P
Quick Installation Guide
Power
Router
3.
. LED Indicators .
2
2
1
1
5.
6.
7. x 1
8.
ports
.
Connect the
power
to the Router’s
.
Plug
power
s
Package Contents
Check the contents of the package
Router
LEDs
Drilling Template
. SIM Card and Battery
. GPS Cable
(This page intentionally left blank.)
1. Turn the device upside down.
2. Remove the SIM Card & Battery cover
by loosening the two Philip screws.
Philip screws
SIM Card &
Battery Cover
3. Set aside the removed SIM Card &
Battery cover.
SIM Card &
Battery Cover
SIM Card slot
Battery compartment
Philip screws
SIM Card &
Battery Cover
4. Insert the SIM Card. Make sure the
SIM Card is pushed all the way into
the slot.
5. Insert the Battery.
Micro
SIM
6. Place the SIM Card & Battery Cover
on the Battery compartment, tighten
the Philips screws till the cover is
tightly secured.
1. Connect the GPS Cable to the GPS-marked mini co-axial (SMC) connector located
on the front panel of the wireless router.
2. Locate a nearby window. Mount the GPS Antenna on the window glass. (Remove
adhesive film on the back of the GPS Antenna prior to mounting in on the window
glass.)
GPS Antenna
Wireless
Router
GPS Antenna
Window
LED Activity Description
OFF LTE service is not connected.
Solid BLUE LTE connected and signal level good. [ RSRP Range -105 dbm to -40 dbm]
Solid YELLOW
Intermittent LTE signal [ RSRP Range -106 dbm to -120 dbm ] or DATA Connection
failed casealso
Solid RED
1. LTE is not functional.
2. SIM card is not provisioned or not properly provisioned.
3. SIM card is not inserted or not inserted properly.
Solid GREEN Reserved
Flashing GREEN Device is under firmware upgrading process.
Flashing LED ( Color
depends on LTE state )
Flashing LED ( Color
depends on LTE state )
Device is under Battery mode, LED Flashing period 5 seconds once
OFF Device is not connected to internet.
Solid
BLUE Internet is connected thru multiple WAN.
Solid GREEN Internet is connected thru single WAN.
Solid RED Device is under error state other than LTE error.
Flashing GREEN Device is under firmware upgrading process.
Device is under Battery mode, LED Flashing period 5 seconds once
OFF
Wi-Fi is not on and not operaonal, Wi-Fi disabled by default in Baery Mode
Solid GREEN Wi-Fi is on and operang normally.
Flash GREEN Device is under firmware upgrading process.
OFF Device is not receiving power.
Solid GREEN Device is completely power on.
Flashing GREEN Device is under power on process.
Flashing YELLOW Device is under Baery mode. Flashing period 5 seconds once
Solid RED Baery needs to be replaced.
Flashing RED 5 mes
Device cannot be power on for any reasons.
(Crical low baery, High temperature)
LTE
System Status
POWER
2.4GHz/5GHz
*Wall Mount Caution:
To ensure proper installation, use three M3.5 screws with a minimum length of 21.8 mm. The input connector
Pour garantir une installation correcte, utilisez trois vis M3,5 d'une longueur minimale de 21,8 mm. Le connecteur
d'entrée doit être orienté vers le sol.
must face toward the floor.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 45cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
* Do not open the system’s cover. If opening the cover for maintenance is a must, only a skill person should do so.
Battery Caution:
- If the battery is incorrectly replaced, there is a danger of explosion.
- Replace only with the same or equivalent type recommended by the manufacturer.
- Discard used batteries according to the manufacturer's instructions.
* N'ouvrez pas le capot du système. Si l'ouverture du couvercle pour l'entretien est indispensable, seule une
personne qualifiée doit le faire.
MISE EN GARDE:
- Si la batterie n'est pas remplacée correctement, il existe un risque d'explosion.
- Remplacez uniquement par un type identique ou équivalent recommandé par le fabricant.
- Jetez les piles usagées conformément aux instructions du fabricant.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
o
o
o
o
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.