ASK8822 WIFI+BT Combo Module Features ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ Highly integrated wireless local area network (WLAN) system-on-chip (SOC) for 5GHZ 802.11ac, or 2.4G/5G 802.11n WLAN applications. Dual-stream spatial multiplexing up to 867 Mbps data rate. Supports 20/40MHz at 2.4GHz and supports 20/40/80MHz at 5GHz. Supports low power SDIO3.0 interface for WLAN and UART/PCM interface for Bluetooth. Supports Bluetooth V4.2 system. Supports WLAN-Bluetooth coexistence.
Antenna Layout General Specification Model Name ASK8822 Product Description Support Wi-Fi/Bluetooth functionalities Dimension L x W x H: 15 x 13 x 2.15 mm (typical) Wi-Fi Interface Support SDIO V3.
Wi-Fi RF Specification 2.4GHz RF Specification Test Items TYP Test Value Standard Value - 1Mbps PER @ -92 dBm ≤-83 SISO Receive Sensitivity - 2Mbps PER @ -90 dBm ≤-80 (11b,20MHz) @8% PER - 5.
Maximum Input Level - MCS=5, PER @ -71 dBm ≤-66 - MCS=6, PER @ -70 dBm ≤-65 - MCS=7, PER @ -68 dBm ≤-64 802.11b : -10 dBm 802.11g/n : -20 dBm 5GHz RF Specification Conditions: VBAT=3.3V ; VDDIO=3.
- MCS=6 PER @ -68 dBm ≤-65 - MCS=7 PER @ -67 dBm ≤-64 - MCS=0, NSS1 PER @ -86 dBm ≤-82 - MCS=1, NSS1 PER @ -84 dBm ≤-80 - MCS=2, NSS1 PER @ -82 dBm ≤-77 SISO Receive Sensitivity - MCS=3, NSS1 PER @ -79 dBm ≤-73 (11ac,20MHz) @10% - MCS=4, NSS1 PER @ -75 dBm ≤-69 PER - MCS=5, NSS1 PER @ -70 dBm ≤-68 - MCS=6, NSS1 PER @ -69 dBm ≤-67 - MCS=7, NSS1 PER @ -68 dBm ≤-62 - MCS=8, NSS1 PER @ -65 dBm ≤-60 - MCS=0, NSS1 PER @ -84 dBm ≤-79 - MCS=1, NSS1 PER @ -81 dBm ≤-77 - MCS=2, NSS1 PER @
36 5180 40 5200 44 5220 48 5240 52 5260 56 5280 60 5300 64 5320 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 5180MHz~5240MHz 5260MHz~5320MHz 5550MHz~5700MHz 5745MHz~5825MHz Bluetooth Specification Bluetooth Specification
Pin Assignments Pin Outline Pin Definition P:POWER I:INPUT O:OUTPUT VDDIO:1.8V or 3.
12 NC I/O No connect 13 NC － No connect 14 NC － No connect Enable pin for WLAN device 15 WL_REG_ON I ON: pull high ; OFF: pull low VDDIO External pull low to shut down WL 16 WL_WAKE_HOST O WLAN to wake-up HOST VDDIO 17 SDIO_CMD I/O SDIO command line 1.8V or 3.3V 18 SDIO_ CLK I/O SDIO clock line 1.8V or 3.3V 19 SDIO_DATA_3 I/O SDIO data line 3 1.8V or 3.3V 20 SDIO_DATA_2 I/O SDIO data line 2 1.8V or 3.3V 21 SDIO_DATA_0 I/O SDIO data line 0 1.8V or 3.
3.3V 1.8V or 41 UART_RXD I Bluetooth UART interface 42 UART_RTS_N O Bluetooth UART interface 43 UART_CTS_N I Bluetooth UART interface 44 NC － No connect 45 NC － No connect 46 NC － No connect 47 NC － No connect 48 NC － No connect 49 HOST_WAKE_BT I HOST wake-up Bluetooth device VDDIO 50 BT_WAKE_HOST O Bluetooth device to wake-up HOST VDDIO 3.3V 1.8V or 3.3V 1.8V or 3.
The Key Material List
Recommended Reflow Profile Package Information Reel A roll of 1500pcs
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC KDB996369 D03v01 Requirements List of applicable FCC rules FCC Part 15 Subpart B, Part 15 Subpart C, Part 15 Subpart E Summarize the specific operational use conditions Not Applicable Limited module procedures Not Applicable Trace antenna designs Refer to Manual Antenna layout RF exposure considerations Refer to FCC certification requirements Label and compliance information Refer to FCC Label Information on test modes and additional testing requirements Not Applicable Additional testing, Part 15 Subp
Industry Canada (IC) CAN ICES-3 (B)/NMB-3(B) This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la norme RSS d'Industrie Canada.
5470-5725 MHz doit être tel que l'équipement respecte encore les normes e.i.r.p. limite; 3. Pour les dispositifs avec une ou plusieurs antennes détachables, le gain d'antenne maximal autorisé pour les dispositifs de la bande 5725-5850 MHz doit être tel que l'équipement soit toujours conforme à la norme e.i.r.p. limites, le cas échéant. 4.
OEM Integration Instructions： This device is intended only for OEM integrators under the following conditions： The module can be used to installation in another host. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module.
IMPORTANT NOTE： This Wireless Module (IC: 1353A-ASK8822) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
