User's Manual

ManualsBrandsAsiatelco Technologies ManualsElectronicsWireless Energy Controller

1 / 13

www.asiatelco.com

Wireless Energy Controller V1.8

model number：EC-P11

INDEX

1 DESCRIPTION --------------------------------------------------------------------------------------------- 3

2 BENEFIT ---------------------------------------------------------------------------------------------- 4

3 FEATURES ---------------------------------------------------------------------------------------------- 4

4 HARDWARE CONFIGURATION ---------------------------------------------------------------------- 5

5 ELECTRICAL SPECIFICATION ---------------------------------------------------------------------- 5

6 SIGNAL DEFINE ----------------------------------------------------------------------------------------- 7

7 DIMENSION ----------------------------------------------------------------------------------------------- 8

8 QUICK USER GUIDE ------------------------------------------------------------------------------------ 9

9 SOFTWARE USER GUIDE ------------------------------------------------------------------------------ 10

Summary of content (13 pages)

PAGE 1
Wireless Energy Controller V1.
PAGE 2
IMPORTANT ANNOUNCEMENT ** High voltage in the controller, operators must be with professional knowledge. ** The wire named “E‐gnd” must be connected with the earth ground all the time. FCC Warning Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
1 DESCRIPTION The Wireless Energy Controller （model number：EC-P11）works as a controller with LED-fixture, and achieve remote control through WIFI wireless. The controller has 2* 0-10V signal for dimming usage, and current sensor is also integrated. 3 / 13 www.asiatelco.
PAGE 4
2 BENEFIT ---- Control and Schedule ON/OFF/DIM for individual fixture or groups of fixtures ---- Remote control and self programmable control mode ---- Customer defined continuous dimming ---- Adjust ON/OFF times and night trimming schedules ---- Monitor the work status & the Energy consumption of every fixture in every minute ---- Track burn hours to verify LED fixture life ---- Detect LED fixture malfunctions remotely ---- Works with any manufactures’ outdoor LED lighting fixture ---- Reduce Energy Cos
PAGE 5
4 HARDWARE CONFIGURATION HARDWARE STANDARD CONFIGURATION LIST Remark WIFI & WIFI antenna port GPS & GPS antenna port 1 * 0-10V Dimming signal output 1 * AC switch inside OPTIONAL LIST 2nd * 0-10V Dimming signal output 2nd * AC switch 5 Interface for Motion sensor input (reserved , not available now ) Interface for Light sensor input (reserved , not available now ) 1*USB device port (reserved , not available now ) ELECTRICAL SPECIFICATION AC/AC PART Absolute Maximum Ratings Items Unit Valu
PAGE 6
Value Items Unit Nominal input value V / AC Input value range V / AC AC Input Frequency range Hz 50 / 60 Switch Output value V / AC same value as input 277 100V/AC to 500V/AC ±10% RMS (load current<150mA) Accuracy of AC current sensor ±5% RMS (load current>150mA) GPS SPECIFICATION Items SPEC Receiver type 50 channel GPS L1 C/A Cold start-----29 s TTFF Warm start-----28 s Hot start-----2 s tracking: -160 dBm Sensitivity acquisition: -147 dBm Horizontal position accuracy * ＜ 10 meters
PAGE 7
6 SIGNAL DEFINE 7 / 13 www.asiatelco.
PAGE 8
7 DIMENSION 8 / 13 www.asiatelco.
PAGE 9
8 QUICK USER GUIDE Case—drive 1xFixture Case—drive 2xFixture 9 / 13 www.asiatelco.
PAGE 10
9 SOFTWARE USER GUIDE  Software Architecture  Important Function Using  system() SYNOPSIS #include int system(const char *command);  ioctl() SYNOPSIS #include int ioctl(int d, int request, ...);  UART Interface  Baud rate setting #include
PAGE 11
write (fd, buf,1024); close(fd);   ADC Interface  Spi read  Spi write  ADC read code DAC Interface  Source code #include
PAGE 12
This command will simultaneously writes data to all CODE registers while updating all DAC registers. It means channel A and channel B will simultaneously update to set value. value: 0~4095 0~3.
PAGE 13
 GPS Interface //i2ccmd i fd int open_fd(void) { char nm[16]; int fd; snprintf(nm, 16, "/dev/%s", I2C_DEV_NAME); if ((fd = open(nm, O_RDONLY)) < 0) { perror(nm); exit(fd); } return fd; } int ValGetNmeaData (unsigned char * data) { int fd = -1; fd = open_fd(); if (fd < 0) { return -1; } if (ioctl(fd, RT2880_I2C_READ_GPS_DATA, data) < 0) { perror("ioctl"); close(fd); return -1; } close(fd); return 0; } Data: input array[] for get data. The max size is 2048.