User Manual

ManualsBrandsAscom ManualsElectronicsBS330 - UPCS Base Station

Installation instructions, BS330 base station

Technical Product Manual - DCT1800-GAP

TD 92093 (1/LZBNB 103 108 R4D) / 2005-09-23/ Ver.C

 2005

Chapter 16 BS330 base station

16.1 General

The base station is connected to the radio exchange by means of a standard twisted pair cable. The base station

is can be fixed to a wall, a ceiling, a pole or a beam, by means of the mounting bracket included. When fixing

the base station to a wall or ceiling the included plugs and screws must be used. When fixing it to a pole or beam

a (not included) strap a flexible metal band must be used.

Versions

The following versions of the BS330 are available:

• BS330/STD: 1880 – 1900 MHz

• BS330/CHINA: 1900 – 1920 MHz

• BS330/LA: 1910 – 1930 MHz

• BS330/US&CDA: 1920 – 1930 MHz

Contents of the box

The box in which the base station is packed contains:

• A base station

• A mounting bracket

• Two screws with wall plugs

Note:

The brand label is not included in the box, but must be ordered separately.

Power distribution

Base stations can be powered by the following sources:

• The radio exchange via the data pairs

• The radio exchange via the data and Express Powering Pairs (EPP)

• A 48 V external supply connected to the radio exchange

• A local AC-adapter

Note:

For more information about power distribution, refer to the section ‘Configuration directions’.

AC-adapter for a base station

A 24 Vdc adapter (BMLNB 101 09/n) can be used. This adapter is provided with an 8-pin RJ45 plug that can

be plugged into one of the data/power connectors of the base station.

Software

If necessary, the software in the base station can be updated by downloading new software to the base station.

Downloading can be performed without disconnecting the base stations. The new software is stored in flash

memory. How to download the software is described in the help file of the application Cordless System Manager

(CSM) for Windows.

Summary of content (10 pages)

PAGE 1
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station Chapter 16 16.1 BS330 base station General The base station is connected to the radio exchange by means of a standard twisted pair cable. The base station is can be fixed to a wall, a ceiling, a pole or a beam, by means of the mounting bracket included. When fixing the base station to a wall or ceiling the included plugs and screws must be used.
PAGE 2
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station Connectors • Two 8-pin RJ45 modular jacks for data and powering • A 6-pin RJ12 modular jack for factory testing The two data/powering connectors are interconnected on the board.
PAGE 3
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 16.2 Base station cabling The base station cable must be a twisted pair cable with 2 pairs minimum for connection of the data lines. Also power can be distributed via these data pairs. A three-pair cable may be used when additional power wires (EPP) are required to increase the distance between base station and radio exchange.
PAGE 4
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 16.3.1 Fixing the mounting bracket to a wall Fix the mounting bracket (see figure 37) to the wall as follows: 1. Hold the mounting bracket with its flat side against the wall such that the text ‘TOP’ is the right way up, and mark the two holes. The minimum distance between the upper hole and the ceiling or any object above the base station must be at least 65 mm (see figure 37).
PAGE 5
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 16.3.2 Fixing the mounting bracket to a ceiling Fixing to a ceiling is done in the same way as the a wall (see paragraph 16.3.1). When the base station has to be positioned above a suspended ceiling, take care that the front of the base station points downwards. 16.3.
PAGE 6
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 1. Fix the cable duct to the wall in one of the positions shown in figure 39. 65 mm 57 mm TOP 125 mm 70 mm 15 mm thick cable ducts 041 75 mm Fig. 39 Minimum distances between a cable duct and the mounting bracket 16.3.5 Securing the base station cable 1. For safety reasons secure the base station cable to a convenient point at about 30 cm from the base station.
PAGE 7
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station NC NC SC1-a SC0-a SC0-b SC1-b EPP-b EPP-a RJ45 modular jack 042 SC = Serial Channel EPP = Express Power Pair NC = Not connected Fig. 40 Connector pinning of the data/power connector 16.3.
PAGE 8
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 1. 16.3.9 Stick the brand label in the front cover recess. Connecting the base station cables 1. If it is required that the cables enter the base station centrally from above, guide the cables through the recess in the middle of the base station as shown in figure 41. 043 Data cable Power cable (if used) Fig. 41 Cables entering the base station centrally from above 2.
PAGE 9
Technical Product Manual - DCT1800-GAP 044 Installation instructions, BS330 base station Fig. 42 Mounting the base station TD 92093 (1/LZBNB 103 108 R4D) / 2005-09-23/ Ver.
PAGE 10
Technical Product Manual - DCT1800-GAP Installation instructions, BS330 base station 72 TD 92093 (1/LZBNB 103 108 R4D) / 2005-09-23/ Ver.