DHA-130 IP/DECT Phone User Guide
PACKAGE CONTENTS .................................................................................................................................................................................................................................................. 1 REQUIREMENTS FOR SETUP AND CONNECTION .............................................................................................................................................................................................................
Change Contrast Setting .......................................................................................................................................................................................................................................................... 57 Handset Extras...........................................................................................................................................................................................................................
Package Contents • D-Link DHA-130 IP/DECT Phone • D-Link DHA-130 Base Station • Power Adapter-AC 12V AC, 1200 mA • Manual and Warranty on CD • Quick Installation Guide • Ethernet Cable (the DHA-130’s Ethernet port is Auto-MDIX) Caution: Using a power supply with a different voltage rating than the one included with the DHA-130 will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
Introduction Before you start, your new DHA-130 IP/DECT Phone will require a multi-port Ethernet router to function and broadband Internet connection. Ideally the router should be configured as a DHCP server in order to simplify setup. Your new DHA-130 IP/DECT Phone will enable you to make VoIP (Voice over Internet Protocol) telephone calls − at a zero or very much reduced cost when compared to regular telephone service − to nearly anywhere, over the Internet.
Hardware Overview – Back Panel Phone Connection Connect to your PSTN phone line using standard phone cabling. LAN Port Connect the Ethernet cable from your router to this port. LAN Port LEDs Factory Reset Button Pressing this button will restore the DHA-130 to its factory default settings. Power Adapter Connect your 12V AC 1.25 A power adapter here. Use the LAN port LED indicators to check link status and port speed.
LED Indicators – Front Panel PSTN A steady amber light indicates the PSTN line is connected. This will be dark if there is no PSTN link. Off Hook A steady green light indicates the phone is off the hook. A blinking green light indicates an incoming call. The light is dark when the phone is on the hook. VoIP If both LED indicators are dark, check to make sure the power adapter is connected and plugged in to a power source. Page Button Press to set off ringer the handset.
Handset Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Earpiece Navigation Key - scrolls up/down through menus. When the D-Life desktop is displayed, push down to access phone records, push up to access D-Life phonebook menu. Left Soft Key – use to select highlighted menu option, perform corresponding function in display Talk Key - to place/receive a call Mode Key – Switch between D-Life VoIP call mode and PSTN call mode.
Getting Started BEFORE YOU BEGIN! Make sure you have a broadband Internet connection, a multi-port Ethernet router such as a broadband router or ADSL router, and an active D-Life account already setup. If you do not have a D-Life account yet, access the D-Life website (www.dlife.com) and set up an account first. For information on using a broadband or ADSL router with the Phone, please read Appendix B Router Port Configuration on page 78. The DHA-130 is very easy to setup and use.
Using the Handset Most of the commonly used functions, for making and receiving calls and storing phone numbers, are controlled using the Soft Keys and Navigation Button on the handset. The right and Left Soft Keys are used to perform an action or option listed on the bottom right or left side of the LCD display. The Navigation Button is used to scroll through menus and other entry functions.
Handset Control Keys The primary control keys for the handset, the soft keys and navigation button, are illustrated here for your reference.
Connect to D-Life The DHA-130 is configured with all the necessary account information including the D-Life account number. If the phone can successfully connect to the Internet, it will automatically establish a connection to the D-Life servers. When D-Life service is established, the LCD indicator on the handset displays “D-Life” in the center of the screen, it is ready to use. 1 D-Life 01/01 Menu 00:15 Names The DHA-130 uses DHCP for to get its network settings.
View D-Life Account Number To view the account number and phone number for your DHA-130, from the Main Menu go to System > D-Life No. The sequence of display screens you will see are simulated below. MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS OK EXIT Select D-Life No. SYSTEM HOST IP NETWORK SETTINGS D-Life No. OK EXIT View D-Life account/phone number. D-Life No.
Incoming Calls The procedures used when answering calls from D-Life VoIP stations or PSTN calls are identical. The main difference is that the LCD display will indicate that the incoming call is a VoIP call or PSTN call. [i] The number of the caller appears as well as the type of call ([i] for VoIP IP call and [P] for PSTN). 123456 04/03 ANSWER 12:15 SILENT To answer the call immediately either press the Talk Key, or the Left Soft Key.
is silenced from the handset while allowing voice and sound to still come through from the other end. To MUTE the handset, press the Right Soft Key while the call is active. [i] [i]: 123456 00:00:04 OPTIONS MUTE Use the Left Soft key to view the options available while the call is active.
Use Speaker Phone While a call is active, the handset can be used in speakerphone mode. Simply choose the SPEAKER option in the OPTIONS menu during the call for hands free speaker mode. OPTIONS SPEAKER HOLD LINE HS PHONEBOOK --------------------------------OK EXIT Putting Calls on Hold To put the active line on hold, use the HOLD LINE option in the OPTIONS menu. While one line is on hold, another incoming call can be answered just like a conventional multiple line PSTN telephone.
Call Waiting When an incoming call occurs while another call is active, the incoming call can be answered while placing the active call on hold automatically. Current call information does not flash in the display. [i] [P] Incoming call indicated by flashing indicator (flashing [i] for VoIP, flashing [P] for PSTN) The name and number of the unanswered incoming call flashes.
To return to the original call, use the SWITCH CALLS option in the OPTIONS menu. Switching to the other line will put the second call on hold while taking the original call off hold. OPTIONS SPEAKER RELEASE & HOLD SWITCH CALLS CONFERENCE OK EXIT 3-Way Conference Calls Conference calls can be held when both lines have active calls. To use the 3-way conference call function, go the OPTIONS menu when both lines are connected (one or both lines can be on hold).
First choose the CONFERENCE option for one line. OPTIONS SPEAKER RELEASE & HOLD SWITCH CALLS CONFERENCE OK EXIT Then SWITCH CALLS to the other line. OPTIONS SPEAKER RELEASE & HOLD SWITCH CALLS CONFERENCE OK EXIT And put the other line in CONFERENCE mode.
The display indicates that the handset is in CONFERENCE mode. [i] [P] CONFERENCE 00:12:37 OPTIONS MUTE To end the conference call or select one line to leave the conference call, bring up the OPTIONS menu again. OPTIONS SPEAKER END CALL 1 END CALL 2 END ALL CALLS OK EXIT Select the option to END ALL CALLS if you want to terminate calls on both lines. Or choose to END CALL 1 or END CALL2 to return to single call mode with the remaining line.
Intercom The DECT phone features handset-to-handset intercom. To use the intercom, press the Intercom button on the handset. INTERCOM HANDSET 1 HANDSET 2 HANDSET 3 HANDSET 4 OK CANCEL The display indicates the handset being paged. To terminate the intercom session, use the CANCEL option.
Making Calls Calls can be made using phone book entries. Frequently used numbers can be added to the Quick Dial list. Calls can also be dialed if they do not appear in your logs or phone book. This section describes how to do all of these. Calling a Phone Book Entry 1. To call a number that is already in the phone book, simply choose NAMES from the desktop display. PHONE BOOK HANDSET D-Life ----------------------------------OK EXIT 2. Choose the HANDSET or D-Life phonebook.
4. Choose OPTIONS. DETAILS MOM [i]123456 OPTIONS EXIT 5. Choose the HANDSET or D-Life phonebook. OPTIONS USE NUMBER EDIT DELETE OK EXIT 6. Select DIAL to call the number.
Using Quick Dial Frequently used numbers can be designated Quick Dial numbers. Quick Dial numbers require pushing only a single button for a few seconds to dial. To place a Quick Dial call, press the number on the keypad assigned to the Quick Dial number. Keys 4 through 9 are used for Quick Dial. To designate a number as a Quick Dial number, it must already be in the Handset phone book. Follow the steps below to set up a Quick Dial entry. 1.
4. The HANDSET phone book appears. Scroll to the name you want to add to the empty Quick Dial slot. HANDSET [P] BOBK [i]CAROLD [P]DENNYJ [i]MOM DETAILS EXIT 5. The HANDSET phone book appears. Choose OK to assign this number to the Quick Dial slot or choose LIST to go back to the HANDSET phone book. DETAILS MOM [i]123456 DEFAULT OK LIST 6. To add new Quick Dial numbers for the remaining keys (5 to 9), use the up and down navigation buttons on the handset to get to the remaining Quick Dial slots.
on the handset. The number appears listed as in the example below. Choose OPTIONS to edit or delete the Quick Dial entry. KEY 4 MOM [i]123456 OPTIONS EXIT 8. Select CHANGE to go to the Handset phone book listed entries and select a new number for the Quick Dial slot. Choose DELETE to remove the Quick Dial assignment, you will be asked to CONFIRM? The decision to delete in a new screen.
Dialing a New Number Phone calls can be made through D-Life VoIP or the regular PSTN telephone network. To make VoIP calls, make sure the handset is in VoIP mode. Use the Mode button to toggle between VoIP mode and PSTN mode. The mode is indicated in the LCD main display. The “i” icon indicates the phone is in VoIP mode. 1 D-Life 10/01 Menu 05:18 Names The “P” icon indicates the phone is in PSTN mode.
D-Life VoIP Calls to PSTN Numbers To place a D-Life VoIP call to a PSTN number, use the number keypad to enter the phone number using the following format: country code + area code + phone number Use the country code even when calling a number in the same country as where you are located.
D-Life VoIP Calls to Other D-Life Accounts To place a D-Life VoIP call to other D-Life account numbers, simply enter the account number and press the green call button on the phone or choose DIAL. 4200105 10/01 DIAL 05:21 DELETE As with regular PSTN phone calls, you will hear the phone ring on the other end. If the line is busy, you will hear a normal busy signal, otherwise the ring will continue until the phone is answered at the remote end.
Local PSTN Phone Calls To place a local call through the regular PSTN network without using VoIP, the phone must be in PSTN mode. Press the Mode button on the handset, notice the “P” icon appears in the main display and the “D-Life” can no longer be seen. 1 10/01 Menu 05:27 Names To place a local PSTN call, enter the number you want to dial and press the green call button on the phone or choose DIAL to initiate the phone call.
Phone Network Settings There are two methods available to change the IP settings of the base station unit. The IP settings can be changed using the handset or by accessing the DHA-130 web manager configuration utility. Read Using the Web Utility for information on change the network IP settings of the DHA-130. View Host Station IP Address 1. To view the IP address of the phone, go to the Main Menu and use the left soft key to “press” OK and choose the first item in the list, the Settings menu.
(broadband or DSL router), the LCD display will look similar to this example: HOST IP [DHCP] 192.168.1.48 OK View Host Station IP Address – PPPoE Connection There are two methods to view the IP address if the phone is configured for PPPoE connection. Use either the SYSTEM menu and choose HOST IP, or use the NETWWORK SETTINGS menu and choose PPPoE to view a display similar to the example below. This only works if the phone is already configured for PPPoE.
Using the Phonebook Phone numbers can be stored in the phonebook by entering them manually or after calling or receiving a call. Use Call Logs to store phone numbers you have dialed or received. See Using Call Logs for a description on how to store dialed and received numbers. Up to one hundred phonebook entries can be stored. To enter phone numbers manually, access the phonebook from the “desktop” D-Life display.
Add Names to Phonebook 1. To create and new phone book entry, scroll down to select the NEW ENTRY option and press the Left Soft Key. HANDSET VIEW RECORD NEW ENTRY QUICK DIAL MEMORY STATUS OK EXIT 2. Enter a name for the phone book entry, use the numbered keypad to key in upper case characters of the alphabet. NEW ENTRY NAME: _ OK DELETE 3.
4. Now enter the phone number as it will be dialed. “Press” OK (with the Left Soft Key) to create the new entry. This number now appears in the Handset Phone Book and can be selected for quick dialing or dialed using the Handset Phone Book. NEW ENTRY NUMBER: 123456_ OK DELETE Check Memory Status The handset has 100 memory slots available for phone book entries. To view how many slots are available, select the MEMORY STATUS option from the Handset menu NAMES > HANDSET > MEMORY STATUS.
Using Call Logs To view records of calls missed, dialed or received got to: MAIN MENU>CALL LOGS>MISSED to view missed calls. MAIN MENU>CALL LOGS>DIALED to view calls that have been dialed from the handset. MAIN MENU>CALL LOGS>RECEIVED to view incoming calls that have been answered. 1. To access the handset phone log menus, go to the MAIN MENU, then to the CALL LOGS menu MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS 10/15 OK 05:35 EXIT 2. In the CALL LOGS menu you can view numbers dialed, received and missed.
3. For example, go to the DIALED call log to see what numbers have been called using the handset. To view the time and date a number was dialed, scroll to select the number and use the DETAILS option. DIALED [i]0012125551234 [i]0012125550303 [i]0012125550022 [P]3125550011 DETAILS EXIT 4. The number dialed, time and date of the call are listed in the display. The number can then be saved. DIALED [i]0012125551234 18:00:00 2007/10/16 OPTIONS EXIT 5.
7. You will need to enter a name, just using the numbered keypad and OK CALL LOG NAME: _ OK DELETE Clear Log Entries The call logs can be cleared (deleted) for all missed, dialed or received calls recorded in the logs. To clear log records go to MAIN MENU>CALL LOGS>CLEAR LOGS and choose the log category to be cleared. You will be prompted to CONFIRM? That you want to clear the log.
Change Network Settings To change the network settings to use a Static IP address, to use PPPoE (user name and password) or to use the factory default network setting, DHCP, use the following menu progression: MAIN MENU>SYSTEM>NETWORK SETTINGS and choose the network connection. The first example below illustrates first how to establish a Static IP Address. The example after that one shows how to set up a PPPoE connection.
3. In the NETWORK SETTINGS menu, choose STATIC IP to go to the IP address entry menu for Static IP address. NETWORK SETTINGS DHCP STATIC IP PPPoE OK 4. A prompt asks if you really want to manually configure the IP address.
5. Enter the static IP address that will be used for the DHA-130 on the LAN. IP address must be entered using the numbers on the keypad of the handset in the form xxx.xxx.xxx.xxx so that all spaces are occupied by a numeral. For example, to enter a static LAN IP address 10.1.1.252, key the numbers as 010.001.001.252, there is no way to enter the “.” portion of the IP address using the handset. Use DELETE to remove unwanted numbers form the menu as displayed.
7. Enter the primary DNS server IP address - usually this address is supplied by the ISP. Press OK to go to the next entry menu. STATIC IP DNS1: 168.095.001.001 OK DELETE 8. Enter the secondary or backup DNS server IP address. Usually this address is supplied by the ISP. Press OK to save the new IP settings and restart the base station. STATIC IP DNS2: OK 168.095.001.002 DELETE 9. The LCD menu informs you that the DHA-130 base station is rebooting.
1 D-Life 10/01 Menu 05:18 Names 40
Setup A PPPoE Network Connection To configure the phone to use a PPPoE network connection, perform these steps: 1. To set up PPPoE configuration for the DHA-130, go to the Network Settings menu. In the Main Menu choose SYSTEM. MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS OK EXIT 2. In the SYSTEM menu, choose NETWORK SETTINGS to see options for changing IP settings and PPPoE configuration. SYSTEM HOST IP NETWORK SETTINGS D-Life No. OK EXIT 3.
4. A prompt asks if you really want to configure a PPPoE connection. PPPoE ENABLE PPPoE? YES No 5. A new prompt asks for the user name. Enter the user name for the PPPoE connection. Use the keypad to enter letters and numbers, Letters from the alphabet are listed in alphabetic order on keys 2 to 9, press the key once to display the first letter listed on the key, press it twice to display the second letter listed, and so forth.
PPPoE REBOOTING PLEASE WAIT 7. A successful connection is indicated when “D-Life” appears in the main screen. The phone is now ready for use.
Handset Settings Settings for the handset include settings the time and date that appears in the display and the format used to display it; the melody and volume of the ringer for intercom, PSTN and IP phone calls, interface language and call services. To change any of these go to the Settings menu from the Main Menu as shown in the example here. Change Sound Settings Ringer tones can be customized so you know what type of call is incoming.
Change VoIP Ringer To change the volume or melody of the VoIP ringer, go to SETTINGS>SOUNDS>VoIP RINGER. 1. Go to the SETTINGS menu MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS OK EXIT 2. Go to the SOUNDS menu SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT SOUNDS VoIP RINGER PSTN RINGER INTERCOM RINGER CALL SERVICES OK EXIT 3. Choose VoIP RINGER.
4. Now use the right and left arrows of the navigation button to adjust the volume and melody. The phone responds with an audible example of the change being made. That is, when the volume is increased, the ringer will ring at that increased volume for a second. Likewise, when scrolling through the melody options, the melody or ring tone will play briefly.
3. Choose KEY TONE. SOUNDS VoIP RINGER PSTN RINGER INTERCOM RINGER KEY TONE OK EXIT 4. Choose to turn the key tone ON or OFF and press OK. KEY TONE ON OFF --------------------------OK CANCEL Turn On/Off Handset Tone To turn off key tones (the noise produced when settings changes are changed or the handset is returned to its re-charger on the base station), go to SETTINGS>SOUNDS>HANDSET TONE. To turn key tone on or off: 1.
2. Go to the SOUNDS menu SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT SOUNDS PSTN RINGER INTERCOM RINGER KEY TONE HANDSET TONE OK EXIT 3. Choose HANDSET TONE. 4. Choose to turn the handset tone ON or OFF and press OK.
Change Equalizer Settings To change the equalizer for normal sound, enhanced bass or treble, go to SETTINGS>SOUNDS>EQUALIZER. To change the equalizer settings: 1. Go to the SETTINGS menu. MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS OK EXIT 2. Go to the SOUNDS menu. SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT SOUNDS INTERCOM RINGER KEY TONE HANDSET TONE EQUALIZER OK EXIT 3. Choose EQUALIZER.
4. Choose the equalizer setting for NORMAL, ENHANCED BASS or ENHANCED TREBLE and press OK. EQUALIZER NORMAL ENHANCED BASS ENHANCED TREBLE --------------------------OK CANCEL Change Time and Date Settings Time and date settings are configured in a separate menu accessed through the handset settings menu. Date and time are displayed on the bottom of the desktop.
2. Select TIME and press OK. DATE AND TIME DATE FORMAT DATE TIME FORMAT TIME OK EXIT 3. Configure the HOUR and MINUTE with the right and left arrows of the navigation button. Press the right arrow to increase the number displayed by 1 for each press, press the left arrow key to decrease the number. Use the up and down arrow keys to select HOUR or MINUTE for configuration.
Change Date Setting To configure the date that is displayed on the bottom of the desktop: 1. From the SETTINGS menu, select DATE AND TIME and press OK. SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT 2. Select DATE and press OK. DATE AND TIME DATE FORMAT DATE TIME FORMAT TIME OK EXIT 3. Configure the MONTH, DAY and YEAR with the right and left arrows of the navigation button.
To configure the time format used for the LCD display: 1. From the SETTINGS menu, select DATE AND TIME and press OK. SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT 2. Select TIME FORMAT and press OK. DATE AND TIME DATE FORMAT DATE TIME FORMAT TIME OK EXIT 3. There are two date formats to choose from, a 12-HOUR will display time in the form HOUR:MINUTE plus A or P to indicate AM or PM, for example ) 01:09P is nine minutes after one o’clock in the afternoon.
Change Date Format For example, to configure the time that is displayed on the bottom of the desktop: 1. From the SETTINGS menu, select DATE AND TIME and press OK. SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT 2. Select DATE FORMAT and press OK. DATE AND TIME DATE FORMAT DATE TIME FORMAT TIME OK EXIT 3. Choose to display the date in numeric form in the order Month/Day/Year or Day/Month/Year.
Change Language Setting To change the language used in the LCD display, got to SETTINGS>LANGUAGE and choose form the languages offered. The default language is English. If the phone is reset, the language settings are also reset to English. The languages supported on the handset are: English, French, German, Italian, Spanish, Portuguese, Swedish, Danish, Norwegian and Finnish. 1. Choose LANGUAGE in the SETTINGS menu and click OK. SETTINGS SOUNDS DATE AND TIME LANGUAGE CALL SERVICES OK EXIT 2.
Change Call Service Settings The phone supports Auto Answer to save an additional step when picking up the handset from the base station cradle to answer a call. When Auto Answer is enabled and the handset is resting in the base station cradle or recharging the battery, to answer an incoming call it is only necessary to pick up the handset. It is not necessary to press the Call button in this circumstance. Likewise when this is enabled, a call is ended by returning it to the base stations cradle.
Change Contrast Setting To change the contrast of the LCD display go to SETTINGS>CONTRAST, select the level of contrast and press OK, the display will use the selected contrast level so you will immediately see how it will appear.
Handset Extras The Extras menu access from the Main Menu includes alarm clock, timer and stopwatch functions. Alarm Clock To use the alarm clock function: 1. Choose the ALARM CLOCK option and press OK. EXTRAS ALARM CLOCK TIMER STOPWATCH -----------------------------------OK EXIT 2. Turn the alarm ON, and click OK to enter the time you want the alarm to sound.
3. Configure the HOUR and MINUTE for the alarm with the right and left arrows of the navigation button. Press the right arrow to increase the number displayed by 1 for each press, press the left arrow key to decrease the number. Use the up and down arrow keys to select HOUR or MINUTE for configuration. ALARM CLOCK HOUR 00 MINUTE <00> ---------------------------------------OK CANCEL Timer To use the alarm timer: 1. Choose the TIMER option and press OK.
Base Station Settings The Base Setup menu is used when there are more than one handset used or when there is more than one base station used. This is also where the base station can be reset to the factory default settings. Adding New Handsets If you are planning to use multiple handsets for a single base station, it will be necessary to register the added handset in order to be recognized by the base station.
Now use the handset being added to do the following: 1. Press the Left Soft Key to use the Menu option at the bottom of the desktop. 01/01 Menu 00:02 Names 2. Now you can navigate through the MAIN MENU options by pressing the arrows of the navigation key. MAIN MENU SYSTEM CALL LOGS SETTINGS EXTRAS OK EXIT 3. Use the navigation key to scroll down to the BASE SETUP option. Press the Left Soft Key to view the BASE SETUP menu.
4. In the BASE SETUP menu, press the Left Soft Key to select the REGISTER option. BASE SETUP REGISTER b SELECT BASE DELETE HANDSET RESET OK EXIT 5. In the REGISTER menu, press the Left Soft Key to select the BASE from the list. The base that has just been activated will appear marked by an asterisk (*) in the list. REGISTER BASE 1 * BASE 2 BASE 3 BASE 4 OK CANCEL 6. You must now enter the PIN number for the handset to establish the DECT connection. Use the number keypad to enter the PIN number.
REGISTER ENTER PIN: **** OK DELETE 7. Once the PIN has been keyed in, press the Left Soft Key to select the OK option. The handset will initiate a search for the base station and a negotiation process will take a few seconds until the DECT connection is established. SEARCHING 8. The antenna icon in the upper left corner of the display will blink on and off during the DECT connection negotiation process.
Menu Names 9. When the DECT connection is established, the channel number used for communication between the base station and the handset appears under the battery icon near the upper left corner of the display. Finally when “D-Life” appears in the center of the display, the phone is ready to use.
2. Choose a base from the list, the asterisk (*) indicates the base station currently broadcasting the registration request. Press OK to go the register handset menu where you will need to enter the PIN. SELECT BASE BASE 1 BASE 2 BASE 3 * BASE 4 OK EXIT 3. You must now enter the PIN number for the base station to establish the DECT connection. Use the number keypad to enter the PIN number. The factory default PIN number is “0000”.
Delete Handset 1. To discontinue the DECT service connection to an individual handset, go to the BASE SETUP menu, choose DELETE HANDSET and press OK. BASE SETUP REGISTER SELECT BASE DELETE HANDSET RESET OK EXIT 2. Choose a handset from the list, and press OK to go the menu where you will need to enter the PIN of the base station to remove the handset from service.
Reset Base Station 1. To reset the base station to its factory default settings including language and network IP settings, use the RESET option in the BASE SETUP menu. BASE SETUP REGISTER SELECT BASE DELETE HANDSET RESET OK EXIT 2. Entering the correct PIN number is required to reset the base station. Enter the PIN number and press OK. RESET BASE ENTER PIN: ****** OK DELETE 3. A correct PIN number entry will bring up a CONFIRM? prompt. The factory default PIN number is “0000”.
Change PIN The PIN number used for the base station can be changed if desired. This is done through the BASE SETUP menu. 1. To change the PIN number for the handset in use, select the CHANGE PIN option in the BASE SETUP menu and press OK. BASE SETUP SELECT BASE DELETE HANDSET RESET CHANGE PIN OK EXIT 2. Entering the current PIN number is required in order change it to a new number. Enter the current PIN number for the handset in use and press OK. The factory default PIN is “0000”.
Using the Web Utility The DHA-130 web configuration utility can be used for limited configuration of the DHA-130. Since the Phone is configured automatically by D-Life, there is not much to configure. The VoIP settings cannot be configured through the web configuration utility. Type the IP address assigned to the DHA-130 by your Router or use the static IP addressed assigned in the form http://xxx.xxx.xxx.xxx Type the Password used to log in to the web manager.
Internet Connection and Time Configuration To configure a fixed IP address for the DHA-130; or if the Phone is connected directly to a broadband modem, the Internet settings can be configured in the Setup menu page. To view the Setup menu, click on the Setup link to view the menu pictured below, choose the network connection option from the My Internet Connection is: pull-down menu, configure the settings and click on the Save Settings button.
Static IP Address The Phone is configured to use automatically assigned IP settings by default. However a fixed IP address can be assigned to the Phone if desired. Static IP address can also be used if the Phone is connected directly to a broadband modem and the ISP has assigned and Static IP address Internet connection. To use Static IP address network setting, select the Static IP option from the My Internet Connection is: pull-down menu and configure IP settings suitable for your LAN.
Internet. If you have been given a user name and password to use for your Internet connection and you are NOT using a router (broadband or DSL router) configured to make the PPPoE connection, the Phone can be configured as a PPPoE client. To configure the PhoneCorder as a PPPoE client, choose the PPPoE option from the My Internet Connection is: pull-down menu, type in the User Name and Password used for authentication, and if desired or required, provide a Service Name and AC Name.
Administration Password Setting To create a new password, type the Old Password, type the new password in the New Password field and then confirm the change in the Retype Password field. The Username (admin) used to access the Router’s management software cannot be changed by the user. Firmware Upgrade To upgrade firmware, type in the name and path of the file or click on the Browse button to search for the file. Click the Upload button to begin copying the file.
The Status information includes IP settings and connection status of the Phone. This information is useful for troubleshooting.
Appendix A Technical Specifications Ethernet Port RJ-45, Auto MDI/MDI-X, 10/100 Mbps Standard Compliance IEEE 802.3 for 10 Mbps Ethernet IEEE 802.3u for 100 Mbps Ethernet Rate Adaptation 10/100 Mbps, Auto-Negotiation Cordless Phone Interface Standard Compliance DECT (Digital Europe Cordless Telecommunication) GAP (Generic Access Profile) Frequency 1880-1900 MHz RF Channels 10 Channels Modulation GFSK Voice Coding ADPCM< 32K bit/s t.
Chassis Material ABS+PC Width Depth Height Weight Power Battery AC Power Adapter Output: AC12V, 1.2A Metal Hydride Cylindrical Cell Size AAA Telephony Call Control Protocol SIP (RFC3261) CODEC G.711 (A-law and U-law) G.726 G.729A iLBC Echo Cancellation G.
Management DHCP (Dynamic Host Configuration Protocol) DHCP Client (RFC2131) Configuration Restore/Backup TELNET TFTP Client Security SIP Authentication VoIP NAT Traversal For firmware upgrade and configuration file download Username/Password control for TELNET and WEB configuration SIP Authentication with MD5 password encryption SIP/STUN Safety/EMI Requirements: UL/CUL EMI Certification FCC Class B BSMI Class B CE Class B Environmental Operating Temperature Storage Temperature Operating Humidity Range
Appendix B Router Port Configuration Most D-Link routers such as the [insert D-Link DSL and broadband router product numbers here] support a feature that allows easy one-click configuration of the DHA-130. So if you are using a D-Link router, chances are you will not need to manually configure the ports. If a one-click VoIP configuration is not supported on your router, check to make sure it is using the latest firmware.
In the example that follows we begin by opening the DI-614+ Web configuration utility and going to Advanced > Virtual Server. Follow the steps on the following pages to open the ports on your router for successful operation of the DHA-130. How to Manually Open Ports on a Router A total of 7 ports must be opened for the DHA-130 to work with most routers or firewalls. To open these ports, please do the following: A. Click Enabled B. Give the Virtual Server a Name (such as i2eye) C.
Appendix C Troubleshooting 1. The DHA-130 will not make a call using a phone number Check that you did not misdial the number. The Phone is not connected to the Internet. The Phone is not registered with the D-Life. It may take the Phone up to 10 minutes to register. Verify all network settings, including DNS. Far side of the call is not registered with a D-Life or compatible VoIP Directory Service. 2. The DHA-130 can’t make direct IP calls Phone is not connected to the Internet.
Appendix D LCD Display Icons Icon Name FUNCTION Antenna Linked to base (steady) or lost link (blinking) Line 1 Line 1 is off hook (Steady) Incoming call from Line 1 (Blinking) Line 2 Line 2 is off hook (Steady) Incoming call from Line 2 (Blinking) New missed call New missed call CID Repeated missed call Repeated missed call CID Line 1 on Hold Line 1 on hold Line 2 on Hold Line 2 on hold Line 1 indicator Line 1 indicator during phone mode Line 2 indicator Line 2 indicator during phone mode
