SCD589 EN User manual 4 FR Mode d’emploi X ES Instrucciones de manejo X
EN Important 13 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A.When the power supply cord or plug is damaged or frayed. B. If the product has been exposed to rain or water. C. If the product does not operate normally by following the operating instructions. D. If the product’s cabinet has been damaged. E. If the product exhibits a distinct change in performance. 14 Do not place this product on an unstable cart, stand or table.
A. Baby unit 1 11 10 2 9 3 8 13 7 4 5 + 6 + + + 12 14 B.
EN Legend of functions A. Baby unit A-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 A-10 A-11 A-12 A-13 A-14 On/Off button (y) Temperature sensor LINK light Volume – / + buttons PAGE button Microphone Night light button ( ) Lullaby button ( ) Play/stop button (2 9) Night light Display Battery compartment cover DC 9V / 300mA power supply jack AC power adapter B.
Legend of functions EN C.What else you need Both units can be battery operated. For battery-operated use you’ll need: – 4 x 1.5V AA non-rechargeable batteries for baby unit. Not supplied. – 2 x 1.2V AAA rechargeable batteries for parent unit. Supplied. D.
EN Contents 2 3 Important Safety Instructions Illustrations 4 Legend of functions 4 4 5 5 Baby unit Parent unit What else you need Display 6 Contents 7 Welcome 9 Getting your baby monitor ready for use 9 10 Baby unit Parent unit 11 Using your baby monitor 12 Other features 12 13 13 14 14 14 15 Adjusting loudspeaker volume Talking to your baby Monitoring baby silently Switching nightlight on / off Paging the parent unit Playing lullabies Connecting / disconnecting belt clip and neck strap 1
EN Getting your baby monitor ready for use + + + + Battery operated use 1 Open the battery compartment by turning the cover (A-12) to the left (1 OPEN), using the palm of your hand. Take off the cover. 2 Insert four 1.5V AA batteries, noting the + and – configuration inside the battery compartment (batteries are not supplied; we recommend Philips Alkaline batteries). 3 Put the battery compartment cover (A-12) back in place.
Getting your baby monitor ready for use EN 5 Place the parent unit in the charging base (B-15). > The POWER light (B-16) lights up red. 6 Leave the parent unit in the charging base until the batteries are fully charged (at least 16 hours). > The POWER light (B-16) will stay red, even when batteries are fully charged. > When the batteries are fully charged, the parent unit can be taken out of the charging base and used cordlessly for at least 8 hours.
EN Using your baby monitor 3 Press and hold the On/Off button (y) (B-6) on the parent unit for 2 seconds. > The sound level lights (B-9) briefly light up orange. > The display (B-8) lights up.The battery indicator ( ) and the room temperature light up in the display. > The LINK light (B-3) lights up red briefly then starts blinking green, searching connection with the parent unit.
Other features EN > The displays (A-11, B-8) give visual feedback on the volume settings of the units: - VoluMe OFF: parent unit volume switched off / monitoring baby silently; - VoluMe 9: minimum volume (parent unit and baby unit); - VoluMe 9 9 9 9 9: maximum volume (parent unit and baby unit). Notes: – If you press the Volume + and – buttons (A-4, B-10) too long, the volume will not be adjusted. – You only need to adjust the baby unit volume when using the talk function (see below).
EN Other features > When sound is detected the sound-level lights (B-9) light up orange. Switching night light on/off 1 Briefly press the night light button ( to switch on the night light (A-10). lights up on both displays. > ), A-7) on the baby unit 2 Press the night light button ( ), A-7) again briefly to switch off the night light (A-10). > The night light dims and gradually switches off. goes out on both displays. > • Switch off the night light when operating the baby unit on batteries.
Other features EN 2 Briefly press the play/stop button (2 9, A-9) to play the selected lullaby. • Briefly press the OK button (B-7) on the parent unit to interrupt playback of the lullaby. Press the play/stop button (2 9, A-9) on the baby unit or the OK button (B-7) on the parent unit again to restart playback of the lullaby. > If the lullaby is not restarted within 60 seconds, the lullaby function will switch off automatically.
EN Other features Connecting the neck strap • Insert the little spindle at the end of the neck strap into the recess (B-11) on the rear of the parent unit. Turn the spindle to the left until it clicks in position. Disconnecting the neck strap • Turn the spindle to the right (TURN 2) and take it off. Menu options Most functions of your baby monitor can be operated via the local buttons on the units.The functions described hereafter can only be operated remotely via the parent unit menu.
Menu options EN 4 Press the MENU button (B-2) again to exit the menu. Note: Always press the buttons MENU (B-2), – and + (B-10) and OK (B-7) shortly. Switching night light on/off • Select Light on? or Light oFF?, using – and + (B-10). Confirm with OK (B-7). Playing lullabies To play or stop a lullaby: • Select LullabY , using – and + (B-10). Confirm with OK (B-7). • Select PlaY? to replay the last played lullaby or StoP LullabY? to stop playback. Confirm with OK (B-7).
EN Menu options Switching sound alert on and off If sound alert is switched on, the parent unit beeps as soon as the second sound level light (B-9) lights orange while the volume is switched off. • Select Sound Alert, using – and + (B-10). Confirm with OK (B-7). • Select Alert on? or Alert oFF?. Confirm with OK (B-7). Setting room temperature range You can set the temperature range (minimum and maximum temperature) for your baby’s room. • Select TeMPerature – – °, using – and + (B-10).
Troubleshooting Problem Possible cause Solution LINK light (A-3, B-3) does not light at all. Parent unit: Power adapter (B-14) not plugged in. Connect power adapter (B-14) to wall outlet. Unit not turned on. Press and hold On/Off button (y) (B-6) for two seconds. Batteries are low. Recharge batteries (B-12). Batteries are empty. Replace batteries (B-12). Baby unit: Power adapter (A-14) not plugged in. LINK light (A3, B-3) flashing red/alarm beeping on parent unit.
EN Troubleshooting Problem Possible cause Solution High pitched noise. Units are too close to each other. Move parent unit away from baby unit (at least 1 meter / 3 feet). Volume on parent unit set too high. Decrease volume (B-10) on parent unit. Volume on parent unit is set too low or switched off. Increase volume on parent unit (B-10). Microphone sensitivity level set too low on parent unit. Increase microphone sensitivity level in parent unit menu.
Frequently asked questions Question Answer The technical specifications show an operating range of 300 meters / 900 feet outdoors. How come my baby monitor manages much less than that? The specified range is only valid outdoors in open air. Inside your house the workable range is limited by the amount and type of walls and/or ceilings in between. Inside the house the operating range will be up to 50 meters / 150 feet. The link is lost every now and then, sound interruptions etc.
EN Important information Technical specifications Power supply – 1 x AC power adapter DC 9V / 300mA for baby unit (supplied). – 1 x charging base DC 9V / 300mA for parent unit (supplied). – 4 x AA 1.5V Alkaline batteries for baby unit. (not supplied). – 2 x AAA NiMH 1.2V rechargeable batteries for parent unit (supplied). Operating range Up to 300 meters / 900 feet in ideal condition.Walls, doors, etc will affect range. Indoors the range is up to 50 meters (150 feet).
Important information EN Environmental information Disposal of your old product Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products.
EN Important information Default factory settings Parent unit – Loudspeaker volume: 1 – Microphone sensitivity: 5 (maximum) – Sound alert: on – Temperature alert: off Baby unit – Loudspeaker volume: 3 – Nightlight: off – Lullaby: 1 – Temperature alert low: 14°C – Temperature alert high: 23°C The FCC ID number is located on the cabinet bottom of Parent Unit and in battery compartment of Baby Unit.
Important information EN RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. For hand held operation, this equipment has been tested and meets the FCC RF exposure guidelines. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.