UM2 Installation and Operation Manual
UM2 CONTENTS Copyrights and Trademarks Sirius XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. Visit www.siriusxm.com/xmlineup for updates. All programming/channel lineup/ XM service subject to change or preemption. All other marks and logos are the property of their respective owners. All rights reserved. Warnings and Compliance ..................................................................................... 1 Introduction ..............................
UM2 WARNINGS AND COMPLIANCE Safety Health Administration (OSHA) has issued headphone usage recommendations for maximum daily exposure and sound pressure levels (measured in decibels (dB)). A decibel is a unit of measure of sound, and decibels increase exponentially as sound gets louder. For example, conversational speech is typically around 60dB, and a rock concert in a stadium is often about 110dB. Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. READ these instructions.
UM2 FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UM2 INTRODUCTION HARDWARE KIT CONTENTS System Features Features of the Polk UM2 marine audio system include: • 4.
UM2 SAFETY INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. When Boating Keep the volume level low enough to be aware of your surroundings. Protect from Water Do not submerge the product in water, as this can cause electric shorts, fire or other damage. Protect from the Elements Use the included cover to protect the wired commander from sunlight, dust, and water while not in use.
UM2 INSTALLATION Bracket Mount Before You Begin Always disconnect the negative battery terminal Important Notes • • • • Lock nuts Before final installation, test the wiring connections to make sure the unit is connected properly and the system works. Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vessel. Install the unit where it does not interfere with operating the vessel and cannot injure passengers.
UM2 Removing the Unit STAINLESS STEEL #8 SCREWS (INCLUDED) To remove the commander, remove bracket mount or remove trim ring and mounting screws, then slide wired commander out of the mounting hole. 1/8” PILOT HOLES FOR SUPPLIED SELF-STARTING SCRWS .180 PILOT HOLES WHEN USING THREADED MACHINE SCREWS Tuner / Amplifier Module Mounting 1. Choose a mounting area for the tuner/amplifier module that will provide plenty of ventilation to prevent the amplifier from overheating.
UM2 WIRING COMMANDER TUNER/AMP MODULE 7
UM2 BASIC OPERATION Audio Menu Power On/Off Press the Menu button (9) on the control panel to access the audio menu. You can navigate through the audio menu items by rotation the Encoder Knob and pressing the Encoder Knob to make selection. Rotate the Encoder Knob clockwise to increase and counter-clockwise to decrease. The unit will automatically exit the audio menu after 10 seconds of inactivity. The following menu items can be adjusted.
UM2 System Menu 1. 2. 3. 4. 5. 6. • Press and hold the Menu button (9) for more than 3 seconds to enter the system menu. “System Settings” will appear on the display, followed by the first menu item, “Key Beep.” Rotate the Encoder Knob (5) to navigate the system menu and highlight the desired item. Press the Encoder Knob to select the item and rotate the Encoder Knob to adjust the selected menu item. Press the Encoder Knob again to enter your selection and return to the menu list.
UM2 TUNER OPERATION Press the Autosave soft button to automatically select strongest stations and store them in the preset list for the selected Band. The new stations replace any stations already stored in that band. Scan Press the Scan soft button to scan stations stored in the current band list. The unit will pause for ten seconds at each preset station. Press Scan again to stop scanning when the desired station is reached. List Press the List soft button to display the preset list.
UM2 PTY Press the PTY soft button access search for stations in your area broadcasting RBDS information. NOTE: Radio stations broadcasting RBDS may not be available in your listening area.
UM2 WEATHER BAND OPERATION LIST Press the Presets soft button to display the preset list. What is the NOAA Weather Radio/Weatheradio Canada? NOAA (National Oceanic and Atmospheric Administration) is a nationwide system that broadcasts local weather emergency information 24 hours a day via the National Weather Service (NWS) network. The U.S. network has more than 530 stations covering the 50 states as well as the adjacent coastal waters, Puerto Rico, the U.S. Virgin Islands and the U.S.
UM2 SIRIUS XM OPERATION SiriusXM preview channel even if your service is not activated. 1. In SiriusXM mode, press and hold the Encoder Knob button (5) to select Direct Channel Entry mode. 2. Rotate the Encoder Knob to select each digit. 3. Press the Encoder Knob button for each digit to enter “000”. 4. Upon entering the last digit, the unit will tune to the SiriusXM ID number for your tuner. 5. Write down the 8 digit ID number for reference.
UM2 Manual Tuning Press the Tune soft button. Press the |<< (3) or >>| (2) soft buttons to decrement/ increment channels down/ up step by step. and tune to the corresponding stored channel. CATEGORY Category mode options are Cat+, Cat- and Info. Rapid Tuning Press and hold |<< or >>| soft buttons to quickly tune next or previous channels in sequence. Category Tuning 1. Press the Cat - /+ soft buttons to change the category.
UM2 Setting the User Passcode 1. Press and hold the Menu button (9) for more than 3 seconds to enter the system menu. 2. Rotate the Encoder Knob (5) to navigate the menu list to the "SiriusXM Setup" option. 3. Press the Encoder Knob button to view "Set Lock Code…". 4. Press the Encoder Knob button to select Set Lock Code. “Enter Lock Code: 0 _ _ _” prompt message will appear. 5. Rotate the Encoder Knob to select a digit (0 – 9) for each number position. The default code is "0000".
UM2 Advisory Messages Reported by the SiriusXM Vehicle Tuner On-Screen Display Check Antenna Advisory Message Check Antenna Cause Explanation/Solution The radio has detected a fault with the SiriusXM antenna. The • antenna cable is either disconnected or damaged. • Check Tuner No Signal Check Tuner No Signal • The radio is having difficulty communicating with the SiriusXM • • Tuner. The tuner may be disconnected or damaged.
UM2 Advisory Messages Reported by the SiriusXM Vehicle Tuner (Continued) On-Screen Display Chan Locked Advisory Message Channel Locked Cause Explanation/Solution The channel that you have requested is Locked by the radio See the section on Parental Control, page 15 for more information Parental Control feature. on the Parental Control feature and how to access locked channels. Enter Code:_ _ _ _ Enter Lock Code User prompted to enter the lock/unlock code.
UM2 USB MP3 OPERATION Removing a USB Device Press the Mode button to select another mode and then remove the USB device from the USB connector. NOTE: After loading a USB device, files and folders are accessed in the order in which they were written to the device. Therefore, the playing order may not be the same as the order in which they are expected to be played. Accessing USB Mode Switching to USB Mode Press the Mode button to enter mode selection display.
UM2 folder sequentially. Press the Intro soft button again to stop Intro Scan and resume normal playback of the current file. Repeat Play Press the Repeat soft button (2) during song play to repeat the current file. Press the Repeat soft button again to stop repeat play. Random Play Press the Random soft button (3) to play all files in the current folder in random, shuffled order. Press the Random soft button again to stop random play.
UM2 BLUETOOTH OPERATION being bumped from the list when more than 5 devices are used, you must lock the device. To Lock/Unlock a device, press the Encoder Knob button to display/change the Locked or Unlocked icon. The UM2 includes built-in Bluetooth technology that allows you to wirelessly connect Bluetooth devices to this head unit for streaming audio playback. Pairing a Bluetooth Device Before you begin, consult the owner’s manual for the Bluetooth device you want to pair with the UM2.
UM2 APP OPERATION will appear on the LCD. Press || again to resume playback. If you change to another mode, the mobile phone audio will pause. Press the Mode button (6) to return to Bluetooth mode and resume mobile phone audio playback. POLK® Specialty Controller is the ultimate wireless remote control for your POLK stereo system.
UM2 SPECIFICATIONS TROUBLESHOOTING General Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 12 Volts Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 ohms per channel Tone Controls: Bass (at 100 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
www.asaelectronics.com v.