Safety Instructions
* For reference only.
Following data for reference
Model
DT82TN/NA-1.2/14
Rated Torque
(N.m)
1.2
Open/close Speed
(cm/s)
14
Working Temperature: -10℃~ +55℃
Input Voltage: AC 100V-240V / 50Hz 60Hz
Radio Frequency: 433.925MHz
Max. Running Time: 4 minutes
功能特点
Built-in Receiver
Stall Protection
Preferred Stop Position
Reset To Factory Mode
Switch Direction
Run/Stop By Pulling Fabric
Weak-current Switch
Selection Function
Electronic Limit
Manually Set The Open
And Close Limits
DT82TN/NA-1.2
P1 button(P1)
Weak-current switch port
LEDIndicator
Common line
Motor down line
Motor up line
SAFETY NOTE
1. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by
children without supervision.
4. If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6. The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or
lessthan70dB(A),e.g.bywritingLpA≤70dB(A).
7. The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10. Do not allow children to play with fixed controls. Keep
remote controls away from children.
11. Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until
the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14. Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation.
Finish assembling
5
Please check assembling is ok
4
Assemble the motor
3
S track
1
2
1
2
3
4
3
4
5
Insert the track
joint board into
the two ends of track
The following steps pls refer to
“the assembly of rubber belt and track”
Track joint board
Insert the track joint bracket
for one end to the track joint
Fix the screws
Track joint
bracket
The joint assembly of track
The assembly of rubber belt for curtain motor
The comfirmation of profiled
material dimension
The length of profiled material = The total
lenth of track - The cap length × 2
The total length of track is 2m
DT82TN/NA
The length of profiled material: 200cm-14cm=186cm
Note:1.The track needs to be engrafted when
the length is less the required
2.The track needs to be engrafted when
inconvenient to transport
7cm
The cap length
DT82TN/NA
Use the screw driver to
place the parts like the
gear into the lower cover
Refer the complete lower
cove in below picture
Thread the rubber belt
into thethe lower cover
Fix the cut rubber belt end
with the belt fasten button
Install the clip part like the referance picture
and insert the track into the lower cover
Seperate the lower cover and the headrail with the
11.5cm belt remaining outside the headrail.Then fix
two fasten buttons on the same side of rubber belt
(it is to figure out the position of the other slip part.)
Keep this end complete
Leave half teeth
Leave one teeth
between these two
belt fasten button
Install the belt fasten button and
the slip part as in the picture
These two slip parts is successfully installed Slide the runners into the track
The hook
1
2
The installation for curtain motor
4
3
Folding method for joint track (for easy transit)
Search for the sl-
ip part connected
with the ends of
the rubber belt
Take off the screw
of the slip parts
and the connection
bracket
Push the connec-
tion parts to one
side
Pull the slip parts
slightly and seper-
ate the connection
part at the same
time
Fold the track
Track folding
method
The slip
parts
The overlap arm
which is connected
to the two ends of
rubber belt
The marked position is in the middle
of the slip parts.Half of the slip
parts are in the head rail as
in the picture
12cm
Slide the slip part to the other end to be flush
with the head rail.Cut the other end of rubber
belt with 12cm left
Install the belt facton button
and the slip part as in the picture
After one slip part installed,then thread the other
end of the belt through the other lower cover
The runner are installed Place the hook and the upper cover into the track
1
Check the position of
brackets,fix it at an
appropiate place on the track
1
Assemble the curtain motor
track at appropriate place,
then fix with screws
2
2
3
4
5
Unfold the
folded track
Combine the
track slowly
Push the con-
nection bracket
to the connec-
tion part
Screw the co-
nnnection bra-
cket and install
the slip parts
The track is
successfully
assembled
Restoring the track
1. Do not expose motor to humid or extreme temperature conditions.
2. Do not cut the antenna and keep it clear from metal objects.
3. Do not allow children to play with this device.
4. If power cable or connector is damaged, do not use.
5. Ensure power cable and aerial is clear and protected from moving parts.
6. Cable routed through walls shall be properly isolated.
7. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
8. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
-1- -2- -3-
Please read following points of attention carefully before setting.
Important Safety Instructions To Be Read Prior To Operation.
1. Operation
①The valid interval time of the buttons is within 10S, if there is no operation within 10S, the emitter
will exit the present setting.
②The motor will LED flashes for hint, please do the next step after the hint.
2. Limits setting
①After the curtain motor installation, pls set the limit switch before usage;
②After setting the limit switches, the motor is with the memorized setting function, pls open and close
curtain one time to recover the limits after re-power on;
③After replacing the track or the curtains, pls cancel the limit switches then resetting again.
3. If lost the emitters, pls repair the new emitters.
M
P2
LithiumCell
3V
P2
a OPEN
a STOP
a CLOSE
b STOP
b CLOSE
b P2 a P2
b OPEN
Fields of Application
It's for motorized curtain track and motorized lift curtain track.
Instruction
A-01
Features
Product Introduction
Caution
Motor Installation
e.g.
Setting Notice
Button Instructions
Specifications
* A channel is the same operation as B channel.