Phono Preamplifier Artcessories User's Manual
IMPORTANT SAFETY INSTRUCTION – READ FIRST This symbol, whenever it appears, alerts you to the presence of uninsulated dangerous voltage inside enclosure-voltage that may be sufficient to constitute risk of shock. This symbol, whenever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. Read Instructions: Retain safety and operating instructions for future reference. Heed all warnings printed here and on the equipment.
Installation: Install the unit in accordance with the instructions printed in the user guide.
INTRODUCTION: Thanks for purchasing Applied Research and Technology’s DJPRE II™, a high quality Phono preamp designed for your home and studio. It acts as an interface between your turntable and your audio recording system. The analog input capacitance can be switched between 100pf and 200pf to optimize your phono cartridge response. A switchable low cut filter removes turntable rumble while leaving the audio pristine.
• • Heavy duty extruded chassis Designed and developed in the USA
The Facts About Turntable Preamps Phonograph Records Have Three Basic Problems 1. It is physically impossible to press them with ridges that allow low frequencies to come out at the same reproduction level as mid and high frequencies. Bass compensation is therefore needed during playback. 2. Records produce a certain amount of hiss which is covered up in post-production by boosting the gain of the high frequencies before pressing. Counter-EQing during playback compensates for this. 3.
INSTALLATION and OPERATION: 1. Connect the AC adapter to the Power Input on the DJPRE II and plug the other end into an AC power outlet. If you are using the unit with a home stereo, see if your receiver or other component has a "switched" output, which will power the unit on and off with the rest of your system. 2. Connect the turntable leads to the Input connectors on the DJPRE II. 3. If the turntable has a separate ground wire, attach it to the Ground terminal on the DJPRE II to reduce hum. 4.
7.
APPLICATIONS: Perfect for: Portable recording, home recording, project studios. The DJPREII may be used in a wide variety of applications and environments. Self-contained in an extruded enclosure, the Phono preamp is designed for continuous professional use. Because the unit is compact and lightweight, mounting location is not critical.
SPECIFICATIONS: Frequency Response: Phono EQ Standard: THD: Hum and Noise: Input Impedance: 10Hz –50kHz, +/-.5dB Conforms to RIAA Curve .01% Typical @ 1kHz >90dB below clipping 47k Ohms in parallel with either 100pF or 200pF Maximum Input Level: 40mVrms @1kHz Maximum Gain: 45dB @ 1kHz In / Out Connections: RCA Maximum Output Level: +6dBu (1.4Vrms) Filter Type/Response: Switchable, Low Cut, -3dB @ 22Hz Power Requirements: 7-12V DC or 9-12V AC @150mA Dimensions HxWxD (in): 1.85 x 4.6 x 4.
WARRANTY INFORMATION: Limited Warranty (USA only) Applied Research and Technology will provide warranty and service for this unit in accordance with the following warrants: Applied Research and Technology, (ART) warrants to the original purchaser that this product and the components thereof will be free from defects in workmanship and materials for a period of three years from the date of purchase.
specific rights and you may have other rights, which vary, from state to state. The warranty terms listed above are only valid within the United States of America. For units purchased outside the United States, an authorized distributor of Applied Research and Technology will provide service. For information on warranty and service policies outside of the U.S., please contact your local distributor.
SERVICE: The following information is provided in the unlikely event that your unit requires service. 1. Be sure that the unit is the cause of the problem. Check to make sure that the unit has power supplied, that all cables are connected correctly, and that the cables themselves are in working condition. You may want to consult with your dealer for assistance in troubleshooting or testing your particular configuration. 2. If you believe that the ART unit is at fault, go to www.artproaudio.com.
www.artproaudio.com E-mail: support@artproaudio.
DJP-5004-101 V1.