Owner's Manual & Assembly Instructions SPl Model No. CM1014 OB1014-B D Q 697.68103-B CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS. 712741204 BUILDING DIMENSIONS * Size rounded off to the nearest foot Exterior Dimensions *Approx.
BEFORE YOU BEGIN.... A2 Owner*s Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model.
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.
SAFETY FIRST.... A4 Safety precautions are important to follow throughout •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. the construction of your building. •Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
CARE & MAINTENANCE.... A5 Web Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch- up scratches as soon as you notice them on your unit. Immediately a wire brush; wash it and apply touch-up paint per manufacturer's Roof: clean the area with recommendation. Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter.
ACCESSORIES.... A6 \VEB ROOF STRENGTHENING (heavy snow load) KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR ANCHOR Model KIT Model No. AK4 Anchor Kit contains heavy-duty steeI augers, 60' (18m) of steet cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground.
THIS PAGE WAS LEFT BLANK INTENTIONALLY
THIS PAGE WAS LEFT BLANK INTENTIONALLY
Foundation F09 The Foundation OPTION 1: ARROW For Your Building FLOOR FOUNDATION KIT: (Order NoFSl0 4-Aor 68387-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This foundation should be used with one of the following: A. To support a plywood deck 8. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FOUNDATION KIT and 2. a n ARROW ANC NORING KIT as an effective method of securing the building to the ground.
Anchoring AIO it is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Arrow Anchoring Kit: (Model No. AK4 or 60298) Recommended for use with any suggested base. Contains: 4 Anchors with Cable, Clamps and installation instruction. Anchoring into _Vood/Post: Use 1/4" Wood Screws. There are 1/4" (O,63cm) dia. holes provided in the frames for proper anchoring• OVERTHE BEABIS AND iNTO THE GROUND Arrow Anchoring Kit: (Model No.
Hardware SPll Remove from bag of screws and save for the last step T T T 65900A 65103 #8-32 Hex Nut (188) #f 0Bxf/2" Black Screw (4) (Packed with Screws) 66923 #8-32x3/8" Bolt (188) 65004 #8Ax5/16" Screw (438) 66045 Handle (2) 66646 Washer (453) (12 sheets of 40) 65109 #8-32 Acorn Nut (4) (Packed with Screws) 67468 Peak Cap (2) (Arrow Logo) 66183 66242 DoorSlide(4) 66382 Lower DoorGuide(4) RoofTrim Cap (2 right &21eft) 6228 TrackSuppo_(2) 67545 21' WeatherStripping(1) 11
Parts List BZ12 Parts in Carton One 12 Part Number Part Description 8576 8577 6264 7743 9984 9983 8538 8539 9369 9373 6515 6020 3719 6278 6403 6892 6893 6015 6869 6797 9366 Right Gable Left Gable Horizontal Door Brace Roof Panel Right Roof Panel Left Roof Panel Right Door Left Door Door Jamb Front Wall Panel Wall Panel Corner Panel Door Handle Brace Vertical Door Brace Door Track Splice Rt. Side Roof Trim Lt.
Parts List 8P13 Parts in Carton Two Part Number Part Description 5986 Rear Rear Front Roof Roof Side 10389 9365 6635 10386 10388 10391 10387 8936 9367 9009 9204 8934 Wall Angle Walt Channel Wall Channel Beam Bracket Beam Wall Channel Side Wall Angle Side Floor Frame Rear Floor Frame Front Floor Frame Gable Brace Roof Beam Brace Ramp Quantity in Carton Check List 2 2 2 4 8 4 4 4 2 2 2 2 1 13
,m =. O O ® O • Parts Needed For ® Step 1 Floor Frame Assemblies 8934 Ramp (1) 9367 Front Floor Frame (2) 8938 Rear Floor Frame (2) 10387 Side Floor Frame (4) $O14 The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front.
O 5986Rear Wall St @p 2 .Frame Parts Needed For ® Assemblies Angle (2) .10389RearWa,,Cha.ne,(2) ® 10388 Side Wall Channel (4) O 10391 SideWall Angle {4) S015 The main frame pieces reinforce the walls. These pieces will later be installed in the center and at the top edge of the side walls and the rear wall.
® Parts Needed For ® Step 3 O10386RoofBeam(8) Roof Beam Assemblies S016 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the center. The left and right roof beam assemblies are made up of two pieces. Hint: These pieces are force-fitted, so you may have to press hard to join them together.
® Parts Needed For • Step 4 DooTrack • 6403DoorTrackSplice(1) Assembly ®936sDoor, ack(21 S017 NOTE: Door Track Splice (painted part) The door track assembly supports the sliding doors and reinforces the front wail. It is made up of three pieces. 6403 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as shown. ©© 2 Insert four screws from the under9366 side only.
® Parts Needed For o Floor Frame Step 5 @ Front Floor Assembly (1) • Side Floor Assembly (2) • Rear Floor Assembly (1) S018 you assembled earlier on the foundation. Assemble the four corners of L_ v the floor frame using two screws at each corner as shown. At the front corners fasten bolts through the bottom with nuts on top. from ' 9367 2 Measure the floor frame diago- nally. When the diagonal measurements are equal, the floor frame is square.
® Parts Needed For ® Corners Step 6 • 6515 Wall Panel (2) • 9373 Front Wall Panel (2) O 6020 Corner Panel (4) S019 Narrow Side NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. Wide Side 6020 Each screw and bolt in the wall re- I Position TOP VIEW SIDE quires a washer.
Step 7 . S020 The mid frame pieces give rigidity to the side and rear walls. 1 Fasten across the rear the middle wal! channel of the rear wall using screws. 2 Fasten the side wall channels across the middle of the side panels using screws. Fasten overlaps in rear corners with bolts and nuts, at two locations. See the figure. NOTE The wall channels behind the front wall panels will be installed in a later step.
Step . Parts Needed For ® Top Frames • Rear Wall Angle Assembly O DoorTrackAssembly{1) (t) o Side Wall Angle Assembly (2) 8021 The top frame pieces give rigidity to the walls and provide a surface for attaching the gables which support the roof. I Fasten the rear wall angle across the inside top of the rear wall using screws. 2 Fasten the sidewall angles across the inside top of the side panels using screws. Side wall angles must overlap rear wall angle in corners.
=m O Parts Needed For O Step 9 Wall Panels 0 6518 Wall Panel (10) S022 Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. 1 Locate all of the wall panels set each one alongside 2 Crimped Rib Underneath and 6515 the building. Fasten the wall panels at the top Detail Showing Center of Panel Screwed to Wall Channel and bottom with screws. 3 Fasten the center of each panel to the wall channel with screws.
® Parts Needed For O Step 1 Front Channel/Door Jamb O 9369 Door Jamb (2) O 9365 Front Wall Channel (2) SO23 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both doorjambs. 1 Fasten the front l 9365@ wall channels in their positions between the end of the side wall channel and the cor- INSIDE OF BUILDING ner panel using screws. Do not put a screw in the hole at the end behind the door opening at this time.
Step 11 • Gable Parts Assemblies Needed For • oeSS'tSR,ghteab,e(2) as_7Le_Gable(2) O 6635 Roof Beam Bracket SR_4 The gables go on top of the front and rear wails to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. '1 Attach the four roof brackets to the gables bolts, washers and nuts. beam using two NOTE Mounting leg of bracket must face toward center of gable.
• Parts Needed For ® Gables/Braces Step 12 • Left Gable Assemblies (2) @ Right Gable Assemblies (2) • 9009 Gable Brace (2) $£25 I Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws. Hint: On the front screws closest to On the reargable, at the overlapping gable, leave out2 center gable leg. usea boltand nut rear wall angle.
® Parts Needed For ® Roof Beam//Braces Step 13 O Main Roof Beam Assembly (1) O Single Roof Beam Assemblies (2) O 9204 Roof Beam Brace (2) SP26 I Wrap the weather stripping tape around the two joined edges of the large left and right gables. See diagram. Cut the weather stripping to length and repeat on next gable set. 2 Spread the two halves ofthe double Weather Stripping roof beam and fasten to the gable brace of the front gable.
Step 14 . Right Parts Roof NeededPanel For ® .9984R,ghtRoo.Pane,(,) Sp-_7 Installing the roof panels is best done with a step ladder. Install the first roof panel at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square and level. This will make the roof (6) Screws panels fit better, and holes will align. Don't anchor the floor frame.
O Parts Needed For O Step 15 Q 9983 Left Roof Panel (1) O 7743 Roof Panel (2) O 6797 Ridge Cap (1) Ridge Cap & Panels SP28 I Install a left roof panel 9983 atthe left rear corner of the roof. Screws To Roof Beam '_ Cover the joint at the peak with weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each roof panel. Do not cut the tape at this time.
O Parts Needed For O Step 16 Riage Cap &Panels • 7743RoofPanel(4) ,GSSgaidgeCap,1, SP29 I Install the second ridge cap 6869 overlapping the first ridge cap while installing four roof panels 7743. Hint. The bolts on the ridge cap need to be leR Ioose to move the ridge cap to the side and overlap the ribs of the next roof panel. Continue weather stripping the ridge. NOTE If roof beam holes do not line up with the roof panel holes, shift the building from left to right.
Q6797Ridge • Parts $P30 Insta!l the third ridge cap 6797 overlapping the second ridge cap while installing the remaining two roof panels 7743. Hint. The bolts on the ridge cap need to be left loose to move the ridge cap to the side and overlap the ribs of the next roof paneL Continue weather stripping the ridge. 2 Install the left 9983 and right roof panel 9984 as you unroll the weather stripping tape, and press it down.
• Step 1 Parts Needed For • RoofT i O6893LeftSJdeRoofTrim(2) .°01°SideRoofT.m, O 6892 Right Side Roof Trim (2) SP31 1 Attach the right, left and side roof trim pieces to the Jower end of the roof paneJs on each side of the buiJding using screws at each panel overlap. NOTE i A single screw fastens both trim | pieces at the overlap.
• Step 19 "Dool'PartsNeededA hlvF°r • =_SSe][H,.,=j so3_ 3719 Door Handle Brace (2) Right Door (1) O 8539 Left Door (1) ®8838 • 6264 Horizontal Door Brace (4) O 6278 Vertical Door Brace (2) The steps on this page tell how to assemble the right door. You will perform exactlythe same procedures for the left door. Each bolt and screw in the door requires a washer. ceed as follows: 1 Attach the door handle Pro- brace and handle to the door shown. Don't tighten the bolt yet.
Step 20 Door • Parts Needed For • Installation & Adjustment o RightDoorAssembly(l} • LeftDoorAssembly(1) SQ33 Gable _ Horizontal Door Brace UoorTrack _ _ It Door Slide I From inside the building, t!/ ;/ put the o C3 bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front fra me track.
SOME FACTS ABOUT RUST 8034 SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears. 1.
