User's Manual

SA Series
Signal Amplifier Installation Manual
Note: Before installing the SA Series Signal Amplifier, please read the entire contents of this manual.
Parts List
Item Description
1 SA Series Signal Amplifier.
2 1.5 meter (59 inches) RF cable.
3
2 meter (78 inches)
power cable.
4 Connector adapter FME female to TNC male.
5 Connector adapter FME male to TNC male.
6 Cellular telephone / Cradle or RF Output Device. (Optional item purchased separately)
7 Antenna Cable. (Optional item purchased separately)
8 Antenna. (Use 3 dBi antenna for optimal performance) (Optional item purchased separately)
Tools and Other Materials Required
Item Description
1 Electric drill (as required for signal amplifier mounting holes).
2 Screwdriver.
3 Qty 4 screws (length and type as required for signal amplifier mounting).
4 Wire cutters / strippers.
5
Qty 2 wire connection insulators or insulating material (as required for
power cable connection to 12V system).
WARNINGS!
∇ NOTICE: During transmitter operation, a minimum distance shall be maintained between the antenna and personnel, in
order to meet the maximum permissible exposure (MPE) limits in section 1.1310 of FCC Rules and Industry Canada’s
Safety Code 6; Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz
to 300 GHz. Refer to Table 1 for distance versus antenna gain.
∇ Mounting a signal amplifier in the engine cavity or on the underside of the vehicle will void the manufacturer’s warranty.
∇ Subjecting the amplifier to voltages greater than 30V
will damage the amplifier and void the manufacturer’s warranty.
∇ Any vehicle with an electrical system of greater than 30V
should use a step-down voltage regulator to bring the voltage
within the operating power range of the amplifier (10-30V
).
∇ Under no circumstances should the amplifier be powered up without a connection to properly matched 50 ohm cellular
antenna or the amplifier may be damaged, resulting in the manufacturer’s warranty being void.
∇ The surface of the amplifier will become hot during operation. Install the amplifier in a location that allows heat to easily
dissipate. Once installed, do not place any object on top of the unit.
Antenna
Gain
(
dBi
)
(
cm
)
(
in
)
0188
1208
2229
32510
42812
53113
63514
73916
84418
94920
10 55 22
11 62 25
12 69 28
13 78 31
14 87 35
15 98 39
Distance to
A
ntenna
Installation
Selecting a Suitable Location to Mount the Signal Amplifier
The surface of the amplifier will become hot during operation. Locate a suitable place to mount the signal amplifier, out of reach of vehicle occupants. Avoid placing or
installing the unit near or on flammable materials. Suggested mounting locations include: under the dashboard, under the seat, or in the trunk. For peak performance
the signal amplifier should be installed using the supplied cabling and connectors. The amplifier should be mounted away from moving parts, as well as excessive heat
and/or moisture.
Installation Cautions
∇ Use caution to avoid drilling through or near fuel lines or fuel tanks; brake lines; or electrical wiring.
∇ Do not mount the signal amplifier or its associated wiring in a location that may interfere with the safe operation of the vehicle.
Installation Of The Signal Amplifier
It is recommended that only certified automotive installation technicians install this product in a vehicle. Installation by any other person is at the risk of
the vehicle owner and operator.
1.
Drill holes and mount the signal amplifier
c in the selected location.
2.
Connect the white-striped black wire of the supplied 2-meter (78
inches) power cable
e to a positive connection on the vehicle’s
electrical system. Choose a 10-30V circuit that is fuse protected and
ignition switched. (Often referred to as the “Accessory Output”)
3.
Attach the solid black wire of the supplied 2-meter (78 inches) power
cable
e to the vehicle’s electrical ground.
4.
Connect the amplifier’s ANTENNA (
) connector to the antenna
using its interface cable
iand if necessary, adapter f or.g
5.
Connect the amplifier’s PHONE (
) connector to the cellular phone’s
handset cradle using the provided 1.5 meter (59 inches) RF cable
d
and if necessary, adapter
f or g.
1
+
3
_
12V DC
2
6
7
8
Limited Warranty
The SA Series Signal Amplifier is warranted free from any defects in material or workmanship for a period of one year. If a defect in material or workmanship is found, the product will be repaired or
replaced at the discretion of the manufacturer, free of charge to the original purchaser. Please return the product along with proof of purchase to the original point of purchase. This warranty is null
and void if the product has been modified, abused, tampered with, subjected to abnormal conditions, or transferred to someone other than the original purchaser.
All brands and trademarks are the property of their respective owners.
D00001408 Rev A Made in North America Page 1 of 2