Administrator’s Handbook Motorola Embedded Software Version 9.0.
Administrator’s Handbook Copyright ©2011 Motorola Mobility, Inc. All rights reserved. MOTOROLA, and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. All other product or service names are the property of their respective owners. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from Motorola Mobility, Inc.
Table of Contents Table of Contents CHAPTER 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About Motorola® Documentation . . . . . . . . . . . . . . . . . . . . . . . . 7 Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Internal Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrator’s Handbook Working with Packet Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 NAT/Gaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Custom Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 IP Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Firewall Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Diagnostics . . . . . .
Table of Contents Physical interfaces commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 PPPoE relay commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 NAT Pinhole commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Security Stateful Packet Inspection (SPI) commands . . . . . . . . . . . . 121 VoIP commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 System commands. . . . . . . . . . .
Administrator’s Handbook
CHAPTER 1 Introduction About Motorola® Documentation ☛ NOTE: This guide describes the wide variety of features and functionality of the Motorola® Gateway, when used in Router mode. The Motorola® Gateway may also be delivered in Bridge mode. In Bridge mode, the Gateway acts as a pass-through device and allows the workstations on your LAN to have public addresses directly on the Internet. Motorola, Inc.
Administrator’s Handbook Documentation Conventions General This manual uses the following conventions to present information: Convention (Typeface) Description bold italic monospaced Menu commands bold sans serif Web GUI page links and button names terminal bold terminal Computer display text Italic Italic type indicates the complete titles of manuals.
Organization This guide consists of five chapters, an appendix, and an index. It is organized as follows: ◆ Chapter 1, Introduction — Describes the Motorola® document suite, the purpose of, the audience for, and structure of this guide. It gives a table of conventions. ◆ Chapter 2, “Device Configuration” — Describes how to get up and running with your Motorola® Gateway.
Administrator’s Handbook 10
CHAPTER 2 Device Configuration Most users will find that the basic Quick Start configuration is all that they ever need to use. The Quick Start section may be all that you ever need to configure and use your Motorola® Gateway. For more advanced users, a rich feature set is available. The following instructions cover installation in Router Mode.
Administrator’s Handbook Important Safety Instructions POWER SUPPLY INSTALLATION Connect the power supply cord to the power jack on the Motorola® Gateway. Plug the power supply into an appropriate electrical outlet. There is no power (on / off) switch to power off the device. ☛ WARNING: The power supply must be connected to a mains outlet with a protective earth connection. Do not defeat the protective earth connection.
Wichtige Sicherheitshinweise NETZTEIL INSTALLIEREN Verbinden Sie das Kabel vom Netzteil mit dem Power-Anschluss an dem Motorola® Gateway. Stecken Sie dann das Netzteil in eine Netzsteckdose. ☛ Warnung: Das Netzteil muss an eine Steckdose, die mit einem Schutzleiter verbunden ist, angeschlossen werden. Die Schutzleiterverbindung darf in keinem Fall unterbrochen werden.
Administrator’s Handbook Motorola® Gateway Status Indicator Lights Colored LEDs on your Motorola® Gateway indicate the status of various port activity. Motorola® Gateway NVG510 status indicator lights Side View Power Ethernet Wireless Wi-Fi Setup Broadband Service Phone 1 Phone 2 LED Power Solid Green = The device is powered. Flashing Green = A Power-On Self-Test (POST) is in progress Flashing Red = A POST failure (not bootable) or device malfunction occurred.
LED Action Service Solid Green = IP connected (The device has a WAN IP address from DHCP or 802.1x authentication and the broadband connection is up). Flashing Green = Attempting PPP connection. Attempting IEEE 802.1X authentication or attempting to obtain DHCP information. Red = Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, 802.1x authentication failed, no IP address from IPCP, etc.).
Administrator’s Handbook Set up the Motorola Gateway Refer to your Quickstart Guide for instructions on how to connect your Motorola® gateway to your power source, PC or local area network, and your Internet access point, whether it is a dedicated DSL outlet or a DSL or cable modem. Different Motorola® Gateway models are supplied for any of these connections. Be sure to enable Dynamic Addressing on your PC. Perform the following: Microsoft Windows: Step 1. Navigate to the TCP/IP Properties Control Panel.
c. Windows Vista and Windows 7 obtain an IP address automatically by default. You may not need to configure it at all. To check, open the Networking Control Panel and select Internet Protocol Version 4 (TCP/IPv4). Click the Properties button. The Internet Protocol Version 4 (TCP/IPv4) Properties window should appear as shown. If not, select the radio buttons shown above, and click the OK button.
Administrator’s Handbook Macintosh MacOS 8 or higher or Mac OS X: Step 1. Access the TCP/IP or Network control panel. a. MacOS follows a path like this: Apple Menu -> Control Panels -> TCP/IP Control Panel b. Mac OS X follows a path like this: Apple Menu -> System Preferences -> Network Then go to Step 2. Step 2. Select Built-in Ethernet Step 3. Select Configure Using DHCP Step 4. Close and Save, if prompted. Proceed to “Accessing the Web Management Interface” on page 19.
Accessing the Web Management Interface 1. 2. Run your Web browser application, such as Firefox or Microsoft Internet Explorer, from the computer connected to the Motorola® Gateway. Enter http://192.168.1.254 in the Location text box. The Device Status Page appears. 3. Check to make sure the Broadband and Service LEDs are lit GREEN to verify that the connection to the Internet is active. Congratulations! Your installation is complete.
Administrator’s Handbook IP Diagnostics page In the event that your connection to the Internet fails, the IP Diagnostics page displays. Follow the on-screen troubleshooting suggestions. For additional troubleshooting information, see “Basic Troubleshooting” on page 69.
Device Status page After you have performed the basic Easy Login configuration, any time you log in to your Motorola® Gateway you will access the Motorola® Gateway Home Page. You access the Home Page by typing http://192.168.1.254 in your Web browser’s location box. Device Access Code You may be required to provide your Device Access Code in order to access the web management configuration pages. The Device Access Code is unique to your device. It is printed on a label on the side of the Gateway.
Administrator’s Handbook The Device Status displays the following information in the center section: Field Description Broadband Broadband Connection ‘Waiting for DSL’ is displayed while the Gateway is training. This should change to ‘Up’ within two minutes. ‘Up’ is displayed when the ADSL line is synched and the PPPoE session is established. ‘Down’ indicates inability to establish a connection; possible line failure.
Tab Bar The tab bar is located at the top of every page, allowing you to move freely about the site. The tabs reveal a succession of pages that allow you to manage or configure several features of your Gateway. Each tab is described in its own section. Help Help is provided in your Gateway. Help is available in the right hand frame on every page in the Web interface. Here is an example: The page shown here is displayed when you are on the System Information page.
Administrator’s Handbook Links Bar The links bar at the top of each page allows you to configure different aspects of the features displayed on the page. For example, on the Home Summary page, the button bar is shown below: Click the links below to be taken to each section.
Link: System Information When you click the System Information link, the System Information page appears. The page displays the following information: System Information Manufacturer This is the manufacturer’s identifier name. Model Number This is the manufacturer’s model number. Serial Number This is the unique serial number of your Gateway. Software Version This is the version number of the current embedded software in your Gateway. MAC Address Unique hardware address of this Gateway unit.
Administrator’s Handbook Link: Access Code Access to your Gateway is controlled through an account named Admin. The default Admin password for your Gateway is the unique Access Code printed on the label on the side of your Gateway. As the Admin, you can change this password to a different one of your own choosing up to 32 characters long. The new password must also include two characters from any these categories: alpha, number, and special characters.
Link: Restart Device When the Gateway is restarted, it will disconnect all users, initialize all its interfaces, and load the Operating System Software. When you make configuration changes, you may be required restart for the changes to take effect.
Administrator’s Handbook Broadband When you click the Broadband tab, the Broadband Status page appears. The Broadband Status page displays information about the Gateway’s WAN connection to the Internet. Broadband Status 28 Line State May be Up (connected) or Down (disconnected). Broadband Connection May be Up (connected) or Down (disconnected). Downstream Sync Rate This is the rate at which your connection can download (receive) data on your DSL line, in kilobits per second.
Gateway IPv4 Address Your ISP's gateway router IP address. MAC Address Your Gateway’s unique hardware address identifier. Primary DNS The IP Address of the Primary Domain Name Server. Secondary DNS The IP Address of the backup Domain Name Server, if available. Primary DNS Name The name of the Primary Domain Name Server. Secondary DNS Name The name of the backup Domain Name Server, if available. MTU Maximum Transmittable Unit before packets are broken into multiple packets.
Administrator’s Handbook Link: Configure When you click the Configure link, the Broadband Configure screen appears. The WAN connection is automatically configured. However, you can adjust the MTU (Maximum Transmittable Unit) value, if your service provider suggests it. The default 1500 is the maximum value, but some services require other values. 1492 is common. If you make any change here, click the Save button.
Home Network When you click the Home Network tab, the Home Network Status page appears. The Home Network Status page displays information about the Gateway’s local area network.
Administrator’s Handbook Home Network Status Device IPv4 Address The Gateway’s own IP address on the network. DHCP Netmask The Gateway’s own netmask on the network. DHCPv4 Start Address The starting IP address of the DHCP range served by the Gateway. DHCPv4 End Address The ending IP address of the DHCP range served by the Gateway. DHCP Leases Available The number of IP addresses of the DHCP range available to be served by the Gateway.
ERP-PBCC Status This tells whether or not the Gateway is honoring legacy 802.11b compatibility mode. DSSS-OFDM Status This is the wireless modulation in use. DSS if in b-only mode, OFDM otherwise. MAC Address Filtering May be either On or Off. If On, you can accept or block client devices from your WLAN based on their MAC address. Power Level May be adjusted up to 100%, lower if multiple wireless access points are in use, and might interfere with each other.
Administrator’s Handbook Link: Configure When you click the Configure link, the Configure page for the Ethernet LAN appears. For each Ethernet Port, 1 through 4, you can select: ◆ Ethernet – auto (the default self-sensing rate), 10M full- or half-duplex, 100M full- or half-duplex, or 1G full- or half-duplex. ◆ MDI-X – auto (the default self-sensing crossover setting), off, or on. You can also enable or disable IPv6 if your LAN devices support or require it. Select On or Off from the pull-down menu.
Link: Wireless When you click the Wireless link the Wireless page appears. The Wireless page displays the status of your Wireless LAN elements. The Wireless page’s center section contains a summary of the Wireless Access Point’s configuration settings and operational status.
Administrator’s Handbook ◆ Network Name (SSID) – preset to a number unique to your unit. You can either leave it as is, or change it by entering a freeform name of up to 32 characters, for example “Hercule’s Wireless LAN”. On client PCs’ software, this might also be called the Network Name. The Wireless ID is used to identify this particular wireless LAN.
Wireless Security By default, Wireless Security is set to WPA-PSK with a pre-defined WPA-Default Key (Wireless Protected Access Pre-Shared Key). Other options are available from the Security pull-down menu: ◆ WEP - Manual: WEP Security is a Privacy option that is based on encryption between the Router and any PCs (“clients”) you have with wireless cards. If you are not using WPA-PSK Privacy, you can use WEP encryption instead.
Administrator’s Handbook Key Length: The pull-down menu selects the length of each encryption key. The longer the key, the stronger the encryption and the more difficult it is to break the encryption. Key: You enter a key using hexadecimal digits. For 40/64-bit encryption, you need ten digits; 26 digits for 128-bit WEP. Hexadecimal characters are 0 – 9, and a – f.
Link: WPS Wireless Protected Setup (WPS) is a not a new security protocol. It is simply an easier way to use existing protocols to provide greater security for your wireless network connections. By default, Privacy is set to Wireless Protected Access (WPA-PSK). WPS allows you to automatically generate a new strong WPA key for your Gateway and any client devices on your wireless network. ☛ Note: Not all client wireless devices support WPS. Refer to their documentation.
Administrator’s Handbook Link: MAC Filtering When you click the MAC Filtering link the MAC Filtering page appears. MAC Filtering allows you to specify which client PCs are allowed to join the wireless LAN by unique hardware (MAC) address. ◆ To enable this feature, select Blacklist or Whitelist from the MAC Filtering Type menu. Blacklist means that only MAC addresses you specify will be denied access; Whitelist means that only MAC addresses you specify will be allowed access.
Link: Subnets & DHCP When you click the Subnets & DHCP link, the Subnets & DHCP page appears. The Server configuration determines the functionality of your DHCP Settings. This functionality enables the Gateway to assign your LAN computer(s) a “private” IP address and other parameters that allow network communication. This feature simplifies network administration because the Gateway maintains a list of IP address assignments.
Administrator’s Handbook DHCP Options ◆ DHCP Lease Time: Specifies the default length for DHCP leases issued by the Router. Enter lease time in dd:hh:mm:ss (days/hours/minutes/seconds) format. ◆ Primary DHCP Pool: Choose the source of the DHCP pool IP address assignment by selecting either the Private (local to your LAN) or Public (assigned remotely) radio button. If you make any changes here, click the Save button, and if prompted, restart the Gateway.
Voice If you click the Voice ink, the Voice page appears. Voice-over-IP (VoIP) refers to the ability to make voice telephone calls over the Internet. This differs from traditional phone calls that use the Public Switched Telephone Network (PSTN). VoIP calls use an Internet protocol, Session Initiation Protocol (SIP), to transmit sound over a network or the Internet in the form of data packets. ◆ The Voice page displays information about your VoIP phone lines, if configured.
Administrator’s Handbook Link: Line Details When you click the Line Details link, the Line Details page appears. ◆ If your service provider has enabled your VoIP phone lines, you can register them by clicking the Register Line 1 or Register Line 2 button(s). ◆ To test if the lines are enabled, click the Ring Line 1 or Ring Line 2 button(s). If enabled and registered, the respective phone will ring until you click the Stop Ring Line 1 or Stop Ring Line 2 buttons.
Link: Call Statistics When you click Call Statistics, the Call Statistics page appears.
Administrator’s Handbook 46 Sum of Franc Loss Fraction Lost: The fraction of RTP data packets lost since the previous SR or RR packet was sent. This fraction is defined to be the number of packets lost divided by the number of packets expected. This will be calculated on every RTCP SR packet. Sum of the fraction lost is calculated with all the RTCP packets. Sum of Franc Loss Squared Fraction lost is squared with every RTCP SR or RR packet. Sum of all this will give the Sum of Franc Loss Squared.
For Line 1 and Line 2:, the two available phone lines, the Call Summary section displays the following information: Call Summary - Line 1 and Line 2 Current Call/Last Completed Call Call Timestamp Date and Time of the current call Type May be Incoming or Outgoing Duration Length of time of call connection Codec in Use Audio codec used for decoding the call packet traffic.
Administrator’s Handbook Firewall When you click the Firewall tab, the Firewall Status page appears. The Firewall page displays the status of your system firewall elements. All computer operating systems are vulnerable to attack from outside sources, typically at the operating system or Internet Protocol (IP) layers. Stateful Inspection firewalls intercept and analyze incoming data packets to determine whether they should be admitted to your private LAN, based on multiple criteria, or blocked.
Link: Packet Filter When you click the Packet Filter link the Packet Filter screen appears. Security should be a high priority for anyone administering a network connected to the Internet. Using packet filters to control network communications can greatly improve your network’s security. The Packet Filter engine allows creation of a maximum of eight Filtersets. Each Filterset can have up to eight rules configured.
Administrator’s Handbook Parts of a filter A filter consists of criteria based on packet attributes. A typical filter can match a packet on any one of the following attributes: ◆ The source IP address (where the packet was sent from) ◆ The destination IP address (where the packet is going) ◆ The type of higher-layer Internet protocol the packet is carrying, such as TCP or UDP Other filter attributes There are three other attributes to each filter: ◆ The filter’s order (i.e.
Working with Packet Filters To work with filters, begin by accessing the Packet Filter pages. Packet Filter ◆ Enable Filter – Select On from the pull-down menu to enable this filter rule. Filter Rule Entry ◆ Action – Select either the drop or pass radio buttons: ◆ ◆ ◆ ◆ ◆ ◆ • drop: If you select drop, the specified packets will be blocked. • pass: If you select pass, the specified packets will be forwarded. Enter the Source IP Address this filter will match on.
Administrator’s Handbook ☛ NOTE: Default Forwarding Filter If you create one or more filters that have a matching action of forward, then action on a packet matching none of the filters is to block any traffic. Therefore, if the behavior you want is to force the routing of a certain type of packet and pass all others through the normal routing mechanism, you must configure one filter to match the first type of packet and apply Force Routing.
Link: NAT/Gaming When you click the NAT/Gaming button, the NAT/Gaming page appears. NAT/Gaming allows you to host internet applications when NAT is enabled. You can host different games and software on different PCs. From the Service pull-down menu, you can select any of a large number of predefined games and software. (See “List of Supported Games and Software” on page 56.) In addition to choosing from these predefined services you can also select a user defined custom service.
Administrator’s Handbook Each time you enable a software service or game your entry will be added to the list of Service names displayed on the NAT Configuration page. To remove a game or software from the hosted list, choose the game or software you want to remove and click the Remove button.
Custom Services To configure a Custom Service, click the Add/Edit Services button. The Custom Services page appears. Enter the following information: ◆ Service Name: A unique identifier for the Custom Service. ◆ Global Port Range: Range of ports on which incoming traffic will be received. ◆ Base Host Port: The port number at the start of the port range your Gateway should use when forwarding traffic of the specified type(s) to the internal IP address.
Administrator’s Handbook List of Supported Games and Software 56 AIM Talk Act of War - Direct Action Age of Empires II Age of Empires, v.1.0 Age of Empires: The Rise of Rome, v.1.
Microsoft Golf 1998 Edition, v 1.0 Microsoft Golf 1999 Edition Microsoft Golf 2001 Edition Midtown Madness, v 1.0 Monster Truck Madness 2, v 2.0 Monster Truck Madness, v 1.0 Motocross Madness 2, v 2.0 Motocross Madness, v 1.
Administrator’s Handbook Link: IP Passthrough When you click the IP Passthrough button, the IP Passthrough page appears. IP Passthrough The IP Passthrough feature allows a single PC on the LAN to have the Router’s public address assigned to it. It also provides PAT (NAPT) via the same public IP address for all other hosts on the private LAN subnet. Using IP Passthrough: ◆ The public WAN IP is used to provide IP address translation for private LAN computers.
NAT Default Server This feature allows you to: ◆ Direct your Gateway to forward all externally initiated IP traffic (TCP and UDP protocols only) to a default host on the LAN, specified by your entry in the Internal Address field. ◆ Enable it for certain situations: – Where you cannot anticipate what port number or packet protocol an in-bound application might use. For example, some network games select arbitrary port numbers when a connection is opened.
Administrator’s Handbook Link: Firewall Advanced When you click the Firewall Advanced button the Firewall Advanced screen appears. All computer operating systems are vulnerable to attack from outside sources, typically at the operating system or Internet Protocol (IP) layers. Stateful Inspection firewalls intercept and analyze incoming data packets to determine whether they should be admitted to your private LAN, based on multiple criteria, or blocked.
Diagnostics When you click the Diagnostics tab, the Troubleshoot page appears. This automated multi-layer test examines the functionality of the Router from the physical connections to the data traffic being sent by users through the Router. You can run all the tests in order by clicking the Run Full Diagnostics button. The modem will automatically test a number of components to determine any problems. You can see detailed results of the tests by clicking the Details buttons for each item.
Administrator’s Handbook Here is an example of the Ethernet Details screen. Test Internet Access These tests send a PING from the modem to either the LAN or WAN to verify connectivity. A PING could be either an IP address (163.176.4.32) or Domain Name (www.motorola.com). You enter a web address URL or an IP address in the respective field and Select your Preferred protocol radio button, IPv4 or IPv6. Click the Ping, Trace, or Lookup button.
Below are some specific tests: Action If PING fails, possible causes are: From the Check Connection page: Ping the internet default gateway IP address DSL is down, DSL or ATM settings are incorrect; Gateway’s IP address or subnet mask are wrong; gateway router is down. Ping an internet site by IP address Site is down. Ping an internet site by name Servers are down; site is down.
Administrator’s Handbook Link: Logs When you click Logs, the Logs page appears. The current status of the Router is displayed for all logs. ◆ You can clear all log entries by clicking the Clear Log button. ◆ You can save logs to a text (.TXT) file by clicking the Save to File button. This will download the file to your browser’s default download location on your hard drive. The file can be opened with your favorite text editor.
The following is an example log portion saved as a .TXT file: P0000-00-00T00:00:08 P0000-00-00T00:00:08 P0000-00-00T00:00:08 P0000-00-00T00:00:08 P0000-00-00T00:00:08 P0000-00-00T00:00:09 P0000-00-00T00:00:12 P0000-00-00T00:00:15 P0000-00-00T00:00:15 P0000-00-00T00:00:15 L6 L7 L7 L6 L6 L6 L5 L5 L7 L7 sdb[306]: log buffer size set to 8192 sdb[306]: libmotopia: Closing /dev/motopia sdb[306]: Loading platform module bcm_enet sdb[306]: SSL CA-root-cert directory is ready.
Administrator’s Handbook Link: Manual Update When you click Manual Update, the Manual Update page appears. Operating System Software is what makes your Gateway run and occasionally it needs to be updated. Your Current version is displayed at the top of the page. To update your software from a file on your PC, you must first download the software from your Service Provider's Support Site to your PC's hard drive. ◆ ◆ ◆ ◆ 66 Browse your computer for the operating system file you downloaded.
Link: Resets In some cases, you may need to clear all the configuration settings and start over again to program the Motorola® Gateway. You can perform a factory reset to do this. It might also be useful to reset your connection to the Internet without deleting all of your configuration settings. ◆ Click the Reset Device button to reset the Gateway back to its original factory default settings. You will be prompted to make sure you want to do this.
Administrator’s Handbook 68
CHAPTER 3 Basic Troubleshooting This section gives some simple suggestions for troubleshooting problems with your Gateway’s initial configuration. Before troubleshooting, make sure you have ◆ read the User Manual; ◆ plugged in all the necessary cables; and ◆ set your PC’s TCP/IP controls to obtain an IP address automatically.
Administrator’s Handbook Status Indicator Lights The first step in troubleshooting is to check the status indicator lights (LEDs) in the order outlined below. Motorola® Gateway NVG510 status indicator lights Side View Power Ethernet Wireless Wi-Fi Setup Broadband Service Phone 1 Phone 2 LED Power Solid Green = The device is powered. Flashing Green = A Power-On Self-Test (POST) is in progress Flashing Red = A POST failure (not bootable) or device malfunction occurred.
LED Action Service Solid Green = IP connected (The device has a WAN IP address from DHCP or 802.1x authentication and the broadband connection is up). Flashing Green = Attempting PPP connection. Attempting IEEE 802.1X authentication or attempting to obtain DHCP information. Red = Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, 802.1x authentication failed, no IP address from IPCP, etc.).
Administrator’s Handbook LED Function Summary Matrix Solid Green = The device is powered. Flashing Green = A Power-On SelfTest (POST) is in progress Solid Green = Powered device connected to the associated port (includes devices with wake-on-LAN capability where a slight voltage is supplied to the Ethernet connection). Flashing Green = Activity seen from devices associated with the port. The flickering of the light is synchronized to actual data traffic.
Solid Green = Good broadband connection (i.e., good DSL Sync). Flashing Green = Attempting broadband connection (i.e., DSL attempting sync). Solid Green = IP connected (The device has a WAN IP address from DHCP or 802.1x authentication and the broadband connection is up). Flashing Green = Attempting PPP connection. Attempting IEEE 802.1X authentication or attempting to obtain DHCP information.
Administrator’s Handbook If a status indicator light does not look correct, look for these possible problems: If LED is not Lit Power Possible problems ◆ Make sure the power adapter is plugged into the DSL Modem properly. ◆ Try a known good wall outlet. ◆ If a power strip is used, make sure it is switched on. ◆ Make sure that any telephone has a microfilter installed. ◆ Make sure that you are using the correct cable.
Factory Reset Switch Lose your Access Code? This section shows how to reset the Motorola® Gateway so that you can access the configuration screens once again. ☛ NOTE: Keep in mind that all of your settings will need to be reconfigured. If you don't have an Access Code, the only way to access the Motorola® Gateway is the following: 1. Referring to the diagram below, find the round Reset Switch opening. Factory Reset Switch: Push to clear all settings 2.
Administrator’s Handbook 76
CHAPTER 4 Command Line Interface The Motorola Gateway operating software includes a command line interface (CLI) that lets you access your Motorola Gateway over a telnet connection. You can use the command line interface to enter and update the unit’s configuration settings, monitor its performance, and restart it.
Administrator’s Handbook CONFIG Commands “VoIP commands” on page 122 “System commands” on page 130 78
Overview The CLI has two major command modes: SHELL and CONFIG. Summary tables that list the commands are provided below. Details of the entire command set follow in this section.
Administrator’s Handbook CONFIG Commands Command Verbs delete help save script set validate view Status and/or Description Delete configuration list data Help command option Save configuration data Print configuration data Set configuration data Validate configuration settings View configuration data Keywords conn ip dns igmp ntp gateway link mgmt phy dsl enet pinhole system log Connection options TCP/IP protocol options Domain Name System options IGMP configuration options Network Time Protocol options
Starting and Ending a CLI Session Open a telnet connection from a workstation on your network. You initiate a telnet connection by issuing the following command from an IP host that supports telnet, for example, a personal computer running a telnet application such as NCSA Telnet. telnet You must know the IP address of the Motorola Gateway before you can make a telnet connection to it. By default, your Motorola Gateway uses 192.168.1.254 as the IP address for its LAN interface.
Administrator’s Handbook About SHELL Commands You begin in SHELL mode when you start a CLI session. SHELL mode lets you perform the following tasks with your Motorola Gateway: ◆ Monitor its performance ◆ Display and reset Gateway statistics ◆ Issue administrative commands to restart Motorola Gateway functions SHELL Prompt When you are in SHELL mode, the CLI prompt is the name of the Motorola Gateway followed by a right angle bracket (>).
SHELL Commands Common Commands arp nnn.nnn.nnn.nnn Sends an Address Resolution Protocol (ARP) request to match the nnn.nnn.nnn.nnn IP address to an Ethernet hardware address. clear [ yes ] Clears the configuration settings in a Motorola Gateway. You are prompted to confirm the clear command by entering yes. clear_certificate Removes an SSL certificate that has been installed.
Administrator’s Handbook log message_string Adds the message in the message_string argument to the Motorola Gateway diagnostic log. loglevel [ level ] Displays or modifies the types of log messages you want the Motorola Gateway to record. If you enter the loglevel command without the optional level argument, the command line interface displays the current log level setting. You can enter the loglevel command with the level argument to specify the types of diagnostic messages you want to record.
You can use the ping command to determine whether a hostname or IP address is already in use on your network. You cannot use the ping command to ping the Motorola Gateway’s own IP address. quit Exits the Motorola Gateway command line interface. reset arp Clears the Address Resolution Protocol (ARP) cache on your unit. reset crash Clears crash-dump information, which identifies the contents of the Motorola Gateway registers at the point of system malfunction.
Administrator’s Handbook show all-info Displays all settings currently configured in the Motorola Gateway. show bridge interfaces Displays bridge interfaces maintained by the Motorola Gateway. show bridge table Displays the bridging table maintained by the Motorola Gateway. show config Dumps the Motorola Gateway’s configuration script just as the script command does in config mode. show crash Displays the most recent crash information, if any, for your Motorola Gateway.
Tx Errors Rx Errors : 0 : 0 Receiver: Incompl Packet Errors No RBD's For Packet Carrier Sense Lost Deferred Replen : : : : Transmitter: TX Retries Single Collisions No Buf For Packet : 0 : 0 : 0 Upper Layers: Rx No Handler Rx No Message Rx Octets Rx Unicast Pkts Rx Multicast Pkts Tx Discards Tx Octets : : : : : : : 0 0 0 0 0 0 30773 267 0 0 31692 10/100 Ethernet phy.enet.
Administrator’s Handbook show ip lan-discovery Displays the LAN Host Discovery Table of hosts on the wired or wireless LAN, and whether or not they are currently online. show ip routes Displays the IP routes stored in your Motorola Gateway. show ipmap Displays IPMap table (NAT). 6rd-check 6rd_ip_v6_conn_name Sends out 6rd loopback packets to the 6rd BG. Verifies 6rd connectivity to the 6rd BG show ipv6 interfaces Display IPv6 interfaces. show ipv6 routes Display IPv6 route table.
This syntax is for the 802.1x-supplicant-supported builds only. The openssl trust list is used in all TLS/SSL situations except the 802.1X supplicant. The default, if you don't append a qualifier, is all. all will show both 802.1x supplicant and openssl trust list root certs; supplicant will show the supplicant trust list root certs; openssl will show openssl trust list root certs show rtsp Displays RTSP ALG session activity data.
Administrator’s Handbook view config Dumps the Motorola Gateway’s configuration just as the view command does in config mode. who Displays the names of the current shell and PPP users. WAN Commands atmping vccn [ segment | end-to-end ] Lets you check the ATM connection reachability and network connectivity. This command sends five Operations, Administration, and Maintenance (OAM) loopback calls to the specified vpi/vci destination. There is a five second total timeout interval.
show ppp [{ stats | lcp | ipcp }] Displays information about open PPP links. You can display a subset of the PPP statistics by including an optional stats, lcp, or ipcp argument for the show ppp command. start ppp vccn Opens a PPP link on the specified virtual circuit.
Administrator’s Handbook About CONFIG Commands You reach the configuration mode of the command line interface by typing configure (or any truncation of con- figure, such as con or config) at the CLI SHELL prompt. CONFIG Mode Prompt When you are in CONFIG mode, the CLI prompt consists of the name of the Motorola Gateway followed by your current node in the hierarchy and two right angle brackets (>>).
set ip ethernet A ip_address consists of two keywords (ip, and ethernet A) and one argument (ip_address). When you use the command to configure your Gateway, you would replace the argument with a value appropriate to your site. For example: set ip ethernet A 192.31.222.57 Guidelines: CONFIG Commands The following table provides guidelines for entering and formatting CONFIG commands.
Administrator’s Handbook option (off) [on | off]: on You can accept the default value for a field by pressing the Return key. To use a different value, enter it and press Return. You can enter the CONFIG step mode by entering set from the top node of the CONFIG hierarchy. You can enter step mode for a particular service by entering set service_name. In stepping set mode (press Control-X to exit. For example: Motorola-3000/9437188 (top)>> set system ...
CONFIG Commands This section describes the keywords and arguments for the various CONFIG commands. Connection commands conns are used to create connections, for example, a WAN or LAN conn. There may be more than one of each depending on your model. names correspond to the system object IDs (OIDs) but you can name them yourself. set conn name name link-oid value Sets the connection named name to point to an associated link specified by the link-oid value.
Administrator’s Handbook set conn name name nat-enable [ on | off ] Specifies whether you want the Motorola Gateway to use network address translation (NAT) when communicating with remote Gateways. NAT lets you conceal details of your network from remote Gateways. It also permits all LAN devices to share a single IP address. By default, address NAT is turned on. set conn name name dhcp-client discover-time seconds The DHCP client parameters appear when the connection type has been set to dhcpc.
set filterset name filterset_name rule number match-eth-p-bits number Matches VLAN priority bits. set filterset name filterset_name rule number match-eth-vid number Matches VLAN id number. set filterset name filterset_name rule number match-eth-src-mac-addr mac_address Matches supplied source MAC address field. set filterset name filterset_name rule number match-eth-dst-mac-addr mac_address Matches supplied destination MAC address field.
Administrator’s Handbook { { { { { { { { { { { { { { { "CS7", 0x38 } "BE", 0x00 } "AF11", 0x0a } "AF12", 0x0c } "AF13", 0x0e } "AF21", 0x12 } "AF22", 0x14 } "AF23", 0x16 } "AF31", 0x1a } "AF32", 0x1c } "AF33", 0x1e } "AF41", 0x22 } "AF42", 0x24 } "AF43", 0x26 } "EF", 0x2e } set filterset name filterset_name rule number match-src-port number [ number ] Matches TCP|UDP source port field or port range.
set filterset filterset_name rule number action do-filterset name Executes the supplied filterset. Default actions If a packet passes through all of a filter's rules without a match, then the filterset's default-actions come into play. These behave the same way that rule actions behave. set filterset name filterset_name default-action set-qos-marker qos_marker_string Tags the packet according to the queue marker name.
Administrator’s Handbook Queue commands Queue configuration typically requires a classification component to set a QoS marker to a packet and a queueing component to schedule the marked packets to the link. This is accomplished using filtersets (“Filterset commands” on page 96).
set queue name queue_name entry number input queue_name Sets the input to a priority or weighted fair queue. set queue name queue_name entry number marker queue_marker Sets the marker with which packets must be marked to be directed to this queue entry's input queue when the type is priority or wfq. set queue name queue_name entry number priority [ 0... 255 ] Sets the priority level of this queue. A lower value indicates a higher priority.
Administrator’s Handbook ip6 conn set ip6 conn name name enable [ on | off ] Enables/disables the IPv6 connection named name. set ip6 conn name name type [ static | autoconf | rd | dp | aiccu ] Type of connection. See below for connection types. set ip6 conn name name mtu octets Specified MTU of connection. set ip6 conn name name side [ lan | wan ] Specified whether the connection is LAN side or WAN side.
set ip6 conn name name 6rd-tunnel ipv4-conn-oid ipv4_name Sets the 6rd connection named name to tunnel over an associated IPv4 connection named ipv4_name. set ip6 conn name name 6rd-tunnel use-dhcp-values [ off | on ] If this parameter is on, 6rd-provisioned parameters are obtained via the underlying DHCPv4 client associated with IPv4 connection named ipv4-name. See “draft-ietf-softwire-ipv6-6rd-10” for DHCP format description. ip6 conn (type = rd, 6rd-tunnel use-dhcp-values = off).
Administrator’s Handbook Delegated Prefix Connections ip6 conn (type = dp, side = lan). A conn of type “delegated prefix” obtains its global prefix information from one or more prefix another IPv6 conn (typically a WAN conn) , if available. In order for a “dp” connection to become fully operational, its underlying link must be up AND the IPv6 connection which delegates the prefix must have created one or more prefixes from which to draw the “dp” connection's global prefix.
set ip6 conn name name dhcp-server addr-count value [ 0 - 256 ] The number of IPv6 addresses available to serve to DHCPv6 stateful clients. If the addr-count parameter is set to zero, the DHCPv6 server operates in “stateless” mode. set ip6 conn name name dhcp-server start-addr-offset value [ 0 - 65536 ] If the addr-count parameter is greater than zero, the start address is an offset from the base address of the prefix which is assigned to the LAN conn.
Administrator’s Handbook IP DNS commands set ip dns domain-name domain_name Specifies the default domain name for your network. When an application needs to resolve a host name, it appends the default domain name to the host name and asks the DNS server if it has an address for the “fully qualified host name.” set ip dns primary-address ip_address Specifies the IP address of the primary DNS name server. set ip dns secondary-address ip_address Specifies the IP address of the secondary DNS name server.
IP IGMP commands Multicasting is a method for transmitting large amounts of information to many, but not all, computers over an internet. One common use is to distribute real time voice, video, and data services to the set of computers which have joined a distributed conference. Other uses include updating the address books of mobile computer users in the field, or sending out company newsletters to a distribution list.
Administrator’s Handbook tion Profile. ◆ Last Member Query Interval – the amount of time in tenths of a second that the IGMP gateway waits to ◆ ◆ ◆ ◆ receive a response to a Group-Specific Query message. The last member query interval is also the amount of time in seconds between successive Group-Specific Query messages. The default last member query interval is 1 second (10 deci-seconds).
set ip igmp snoop-entry-time seconds The snoop-entry-time is the amount of time an entry will remain in the snooping table (in seconds) after being added. An entry is added when a “JOIN” is seen from a multicast client. Any new joins (triggered by upstream queries) will reset the timeout back to seconds. If no additional joins are seen, the entry will expire after seconds. Default is 130. set ip igmp snooping-unreg-mode [ block | flood ] The snooping-unreg-mode can be set to block or flood.
Administrator’s Handbook Application Layer Gateway (ALG) commands These commands allow you to enable or disable the router’s support for a variety of Application Layer Gateways (ALGs). An application layer gateway (ALG) is a NAT component that helps certain application sessions to pass cleanly through NAT. Each ALG has a slightly different function based on the particular application’s protocol-specific requirements. An internal client first establishes a connection with the ALG.
set ip dynamic-dns service-type [ dyndns ] set ip dynamic-dns username myusername set ip dynamic-dns password mypassword set ip dynamic-dns hostname myhostname set ip dynamic-dns retries [ 1 - 64 ] Enables or disables dynamic DNS services. The default is off. If you specify dyndns.org, you must supply your hostname, username for the service, and password. Number of retries defaults to 5.
Administrator’s Handbook set link name name ppp magic-number [ on | off ] Enables or disables LCP magic number negotiation. set link name name ppp protocol-compression [ off | on ] Specifies whether you want the Gateway to compress the PPP Protocol field when it transmits datagrams over the PPP link. set link name name ppp max-failures integer Specifies the maximum number of Configure-NAK messages the PPP module can send without having sent a Configure-ACK message.
set link name name ppp peer-dns [ on | off ] Controls whether the Gateway accepts nameserver addresses from the peer. ◆ The default is on, which means the Gateway expects to get nameserver addresses when the PPP link comes up. This especially applies when the primary WAN connection is PPP. ◆ However, there are some unusual situations where the PPP connection is not the primary WAN, for example when the connection is used only for management.
Administrator’s Handbook http://some_url.com:port_number or http://123.45.678.910:port_number On units that support SSL, the format for the ACS URL can also be: https://some_url.com:port_number or https://123.45.678.910:port_number set management shell idle-timeout [ 1...120 ] Specifies a timeout period of inactivity for telnet access to the Gateway, after which a user must re-login to the Gateway. Default is 15 minutes for telnet.
Remote access commands set management remote-access http-port [ 1 - 65534 ] Sets the web access port for remote access management of the Gateway. Default is port 51003. set management remote-access http-idle-timeout [ 1...120 ] Specifies a timeout period of inactivity for remote HTTP access to the Gateway, after which a user must re-login to the Gateway. Default is 20 minutes for HTTP. set management remote-access http-total-timeout [ 1...
Administrator’s Handbook set management remote-access telnet-max-clients number Specifies the maximum number of client sessions for remote telnet access management. Defaults to 4. set management remote-access ssh-port [ 1 - 65534 ] Specifies the port number for secure shell (SSH) communication with the Motorola Gateway. Defaults to port 22. set management remote-access ssh-idle-timeout [ 1...
Physical interfaces commands DSL interfaces set physical dsl enable [ off | on ] Turns the physical DSL interface off or on. Default is on. set physical dsl loopback [ off | on ] Turns the DSL loopback mode off or on. Default is off. set physical dsl modulation auto [ off | on ] Turns automatic DSL modulation off or on. Default is on. set physical dsl transport [ atm | ptm | auto | off ] Sets the DSL transport mode: Asynchronous (atm), Packet (ptm), Automatic (auto), or none (off). Default is auto.
Administrator’s Handbook set physical dsl atm vcc 2 datapath [ phy0fast | phy0interleaved ] Sets the ATM datapath, Fast Path or Interleaved. Default is phy0fast. set physical dsl atm vcc 2 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp | vcmux-eth | vcmux-ipoa | vcmux-pppoa ] Specifies the data link encapsulation type. Default is llcsnap-eth. set physical dsl atm vcc 2 vpi [ 0 - 255 ] Sets the Virtual Path Identifier (vpi) for the circuit. Default is 8.
Ethernet interfaces set physical enet 1 mac-addr-override mac_addr You can override your Gateway’s Ethernet MAC address with any necessary setting. Some ISPs require your account to be identified by the MAC address, among other things.
Administrator’s Handbook set physical wireless ssid 1 access-type [ none | allow | deny ] Specifies the type of address list for defining MAC address filtering. If set to allow, only hosts with the specified addresses will be permitted to join the WLAN of the specified SSID. If set to deny, any hosts except those with the specified addresses will be permitted to join the specified SSID. Default is none.
NAT Pinhole commands NAT pinholes let you pass specific types of network traffic through the NAT interfaces on the Motorola Gateway. NAT pinholes allow you to route selected types of network traffic, such as FTP requests or HTTP (Web) connections, to a specific host behind the Motorola Gateway transparently. To set up NAT pinholes, you identify the type(s) of traffic you want to redirect by port number, and you specify the internal host to which each specified type of traffic should be directed.
Administrator’s Handbook set security spi portscan-protect [ on | off ] Enables or disables whether to detect and drop port scans. Default is on. set security spi invalid-tcp-flags-drop [ on | off ] Enables or disables whether packets with invalid TCP flag settings (NULL, FIN, Xmas, etc.) are to be dropped. Default is on. set security spi flood-limit enable [ on | off ] Enables or disables whether packet flooding should be detected and offending packets be dropped. Default is on.
set voip phone n sip-registrar-server-transport [ udp | tcp ] Specifies the SIP registration server transport protocol for the specified phone. Default is UDP. set voip phone n sip-expires-time [ 5 - 65535 ] Specifies the SIP registration server time-out duration from 0 – 65535 seconds for the specified phone. Default is 3600 (1 hour).
Administrator’s Handbook set voip phone n codec G726_24 priority [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | none ] Assigns a priority to the G726-24 codec, a common audio media type implementation at 24 kbit/s. set voip phone n codec G726_32 priority [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | none ] Assigns a priority to the G726-32 codec, a common audio media type implementation at 32 kbit/s.
set voip phone n sip-advanced-setting sip-qos-p-bit-value [ 0 - 7 ] Sets a QoS P-bit value for the SIP session. Default is 6. set voip phone n sip-advanced-setting sip-qos-marker-value value Sets a QoS marker on the SIP session packets on the specified phone line. set voip phone n sip-advanced-setting rtp-qos-tos-value [ 0 - 255 ] Specifies the RTP Diff-Serv Type of Service (ToS) values for Quality of Service (QoS) assignment. Default is 184.
Administrator’s Handbook Codec G726_24 Codec G726_32 Codec G726_40 packetization-time 20 20 20 jitter-max-reorder-delay 50 50 50 jitter-max-accept-late-seqnum 200 200 200 jitter-initial-delay 80 80 80 jitter-exe-frame-del-mode off off off jitter-max-transit-delay 250 250 250 jitter-peak-transit-delay 475 475 475 jitter-delay-buff-inc 10 10 10 jitter-transit-delay-threshold 10000 10000 10000 Syntax is as follows: set voip advanced-telephony-setting codec codec packeti
set voip advanced-telephony-setting rtp-port-range-start value set voip advanced-telephony-setting rtp-port-range-end value Sets the start and end port values for the RTP port range. Although no ports are specified for the RTP protocol, the RTP data is to be carried on an even UDP port number. The defaults in use for the Motorola Gateway are 8024 and 8036, respectively. set voip advanced-telephony-setting rtcp-option [ off | on ] Turns Real-Time Transport Control Protocol on or off.
Administrator’s Handbook set voip phone n call-feature call-forwarding-on-busy-option [ off | on ] call-forwarding-on-busy-option – turns call forwarding when line is busy on or off.. Default is off. set voip phone n call-feature call-forwarding-on-no-answer-option [ off | on ] call-forwarding-on-no-answer-option – turns call forwarding when there is no answer on or off. set voip phone n call-feature call-waiting-option [ off | on ] call-waiting-option – enables or disables call waiting.
set voip phone n dsp-settings vad-option [ off | on ] When vad-option is set to on – enables Voice Activity Detection/Comfort Noise Generation. When speech is not present, the CNG algorithm generates a noise signal at the level sent from the transmit side.
Administrator’s Handbook System commands set system name name Specifies the name of your Motorola Gateway. Each Motorola Gateway is assigned a name as part of its factory initialization. The default name for a Motorola Gateway consists of the word “Motorola-7000/XXX” where “XXX” is the serial number of the device; for example, Motorola-7000/9437188. A system name can be 1 – 255 characters long.
◆ high - High-level informational messages or greater; includes status messages that may be significant but do not constitute errors. The default. ◆ alerts - Warnings or greater; includes recoverable error conditions and useful operator information. ◆ failures - Failures; includes messages describing error conditions that may not be recoverable.
Administrator’s Handbook Debug Commands When you are in SHELL mode, the DEBUG prompt is the name of the Motorola Gateway/DEBUG followed by a right angle bracket (>). For example, if you open a CLI connection to the Motorola Gateway named “Motorola3000/9437188,” then type “debug” you would see Motorola-3000/9437188/DEBUG> as your prompt. Debug level is available for field debugging purposes.There is no service and quality level guarantee from Motorola.
wireless voip sip dsp 133
Administrator’s Handbook 134
CHAPTER 5 Technical Specifications and Safety Information Description Dimensions: (Unit without the stand) H: 194 mm, W: 32 mm, D: 148 mm, Weight: 403 grams (Unit with the stand) H: 210 mm, W: 77 mm, D: 166 mm, Weight: 449 grams Communications interfaces: The Motorola® Gateways have an RJ-11 jack for DSL line connections and a 4port 10/100Base-T Ethernet switch for your LAN connections, and a 400 mW wireless radio for Wi-Fi connections. Power requirements ■ Min10.5W/110VAC ■ Max17.2W/110AC ■ Min 8.
Administrator’s Handbook Agency approvals North America Safety Approvals: ■ United States – UL 60950, Third Edition ■ Canada – CSA: CAN/CSA-C22.2 No.
Manufacturer’s Declaration of Conformance ☛ Warnings: This is a Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Adequate measures include increasing the physical distance between this product and other electrical devices. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. United States.
Administrator’s Handbook Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord).
Important Safety Instructions Caution DO NOT USE BEFORE READING THE INSTRUCTIONS: Do not connect the Ethernet ports to a carrier or carriage service provider’s telecommunications network or facility unless: a) you have the written consent of the network or facility manager, or b) the connection is in accordance with a connection permit or connection rules.
Administrator’s Handbook 47 CFR Part 68 Information FCC Requirements 1. The Federal Communications Commission (FCC) has established Rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones. 2.
j) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this Motorola® Series Gateway does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or qualified installer. RF Exposure Statement: NOTE: Installation of the wireless models must maintain at least 20 cm between the wireless Gateway and any body part of the user to be in compliance with FCC RF exposure guidelines.
Administrator’s Handbook Caring for the Environment by Recycling When you see this symbol on a Motorola product, do not dispose of the product with residential or commercial waste. Recycling your Motorola Equipment Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items.
Milieubewust recycleren Als u dit symbool op een Motorola-product ziet, gooi het dan niet bij het huishoudelijk afval of het bedrijfsafval. Uw Motorola-materiaal recycleren. Gooi dit product niet bij het huishoudelijk afval het of bedrijfsafval. In sommige landen of regio's zoals de Europese Unie, zijn er bepaalde systemen om elektrische of elektronische afvalproducten in te zamelen en te recycleren. Neem contact op met de plaatselijke overheid voor informatie over de geldende regels in uw regio.
Administrator’s Handbook Please visit http://www.motorola.com/recycle for instructions on recycling.
Appendix A Motorola® Gateway Captive Portal Implementation This section contains information about the Motorola Gateway Captive Portal Support. Overview Motorola follows the 2Wire RPC specification for implementation of Captive Portal. The Captive Portal feature redirects all TCP traffic destined to port 80 and redirects it to a captive portal URL. White-IP address list can be configured. HTTP traffic destined to IP addresses in the white IP address list will not be redirected.
Administrator’s Handbook Captive Portal RPC RPC supported per 2Wire requirements that will set Captive Portal Parameters. PAGE 147 X_00D09E_GetCaptivePortalParamsResponse response message for X_00D09E_GetCaptivePortalParams request.
Administrator’s Handbook 148
Device List 24 DHCP lease table 85 Diagnostic log 85, 88 Diagnostics 61 Documentation conventions Index Symbols !! command 8 82 E A Ethernet statistics Access Code 26 Address resolution table 87 Administrator password 81 Arguments, CLI 92 ARP 85 F filter parts 50 parts of 50 Command 83, 90 filter sets disadvantages 49 using 51 B Broadband Status 28 filters using 50, 51 firewall 87 C Firewall Advanced 60 Firewall Status 48 Call Statistics 45 Captive Portal 145 CLI 77 !! command 82 Argume
Administrator’s Handbook Logs 64 System commands System Information M MAC Filtering 40 Management commands Manual Update 66 Memory 88 T 113 tab bar 23 Telnet 81 Telnet command 89 Test Web Access 62 TFTP server 83 Traceroute 62 Trivial File Transfer Protocol Troubleshoot 61 Truncation 92 N NAT Pinhole commands NAT/Gaming 53 NSLookup 62 NTP commands 109 121 U P Packet Filters Password User name 81 User password 49 Administrator 81 User 81 81 V Physical interfaces commands Ping 62 Ping command 8
Motorola® Mobility DSL Gateways Motorola Mobility, Inc. 600 North U.S.
Administrator’s Handbook 152
