IPC1500 IP Camera STATIC VIEW 802.
Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents CHAPTER 1 INTRODUCTION ......................................................................................................... 1 Overview............................................................................................................................................ 1 Physical Details ................................................................................................................................ 3 Package Contents ...............................................
P/N: 9560GV0101 Copyright 2005. All Rights Reserved. Document Version: 2.1 All trademarks and trade names are the properties of their respective owners.
Chapter 1 Introduction 1 This Chapter provides details of the Wireless Network Camera's features, components and capabilities. Overview The Wireless Network Camera has an Integrated Microcomputer and a high quality CMOS digital-Image-Sensor, enabling it to display high quality live streaming video over your wired LAN, the Internet, and for the Wireless Network Camera, an 802.11g Wireless LAN.
• • • • • • • Multi-Protocol Support. Supporting TCP/IP networking, SMTP (E-mail), HTTP and other Internet related protocols, the Wireless Network Camera can be easily integrated into your existing network. Easy Configuration. A Windows-based Wizard is provided for initial setup. Subsequent administration and management can be performed using a standard web browser. The administrator can configure and manage the Wireless Network Camera via the LAN or Internet. Viewing/Recording Utility.
• Wired and Wireless Network Support. The Wireless Network Camera supports either wired and wireless transmission. • • WEP Support. Full WEP support (64/128 Bit) on the Wireless interface is provided. WPA-PSK Support. The WPA-PSK (WPA1) standard is also supported, allowing advanced encryption of wireless data. Physical Details Figure 2: Wireless Network Camera Front Lens No physical adjustment is required or possible for the lens, but you should ensure that the lens cover remain clean.
Wireless LED (Amber) (Wireless Network Camera only) On - Wireless interface is active. Off - Wireless interface is not available. Blinking - Data is being transferred via the Wireless interface. LAN LED (Amber) On - LAN port is connected to a hub or switch. Off - LAN port is not connected. Blinking - Data is being transmitted or received via the LAN port. Rear Antenna Attach the supplied antenna here. The antenna is adjustable; best results are usually obtained with the antenna positioned vertically.
Package Contents The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately. 1. 2. 3. The Wireless Network Camera Installation CD-ROM Quick Installation Guide 4. 5. 6. Power adapter Camera Mount Mounting Screws (for wall mounting) 7.
2 Chapter 2 Basic Setup This Chapter provides details of installing and configuring the Wireless Network Camera. System Requirements • To use the LAN interface, a standard 10/100BaseT hub or switch and network cable is required. • To use the Wireless interface on the Wireless Network Camera, other Wireless devices must be compliant with the IEEE802.11b or IEEE802.11g specifications. All Wireless stations must use compatible settings. Installation Figure 3: Camera Assembly 1.
For the Wireless Network Camera, this disables the Wireless Interface, because only one interface can be active. The LAN interface is recommended for initial configuration. The default Wireless settings for the Wireless Network Camera are: Mode: Infrastructure ESSID: ANY Wireless Security: Disabled 3. Power Up Connect the supplied 5Vpower adapter to the Wireless Network Camera and power up. Use only the power adapter provided. Using a different one may cause hardware damage. 4.
Setup using the Windows Wizard Initial setup should be performed using the supplied Windows-based setup Wizard. This program can locate the Wireless Network Camera even if its IP address is invalid for your network. You can then configure the Wireless Network Camera with appropriate TCP/IP settings for your LAN. Subsequent administration can be performed with your Web browser, as explained in Chapter 3 - Web-based Administration. Setup Procedure 1. Insert the supplied CD-ROM into your drive.
• 3. Select the desired Camera from the list on the left. The current settings for the selected Camera will be displayed in the table on the right. • Click Next to continue. If the Administrator Name and Administrator Password have been set, you will be prompted to enter them, as shown below. • • If using the default values, enter administrator for the name, and leave the password blank. Otherwise, enter the Administrator Name and Administrator Password set on the User screen.
Figure 8: TCP/IP Settings • Enter an unused IP Address from within the address range used on your LAN. • The Subnet Mask and Default Gateway fields must match the values used by PCs on your LAN. • The Primary DNS address is required in order to use the E-mail alert or Dynamic DNS features. Enter the DNS (Domain Name Server) address recommended by your ISP. • The Secondary DNS is optional. If provided, it will be used if the Primary DNS is unavailable. Click Next to continue. 6.
• 7. Channel - For Ad-hoc mode, select the channel used by your other Wireless devices. (For Infrastructure mode, the Access Point determines the channel used.) Click Next to continue to the Security screen, shown below, choose Disabled, WEP or WPA-PSK Figure 10: Security Screen 8. If you chose WEP(64 or128) , the following screen is shown below. Figure 11: WEP Key Settings 9. • WEP Authentication - Select the option used on your Wireless LAN.
Figure 12:WPA-PSK Settings • Encryption - Select the desired option. Wireless Stations must use the same method. • Pre-Shared Key - Enter the key value. Data is encrypted using a key derived from the network key. Other Wireless Stations must use the same network key. The PSK must be from 8 to 63 characters in length. Click Next to continue to the following screen. 10. This screen allows you to enter a suitable Description, and set the correct Time Zone, Date, and Time.
Figure 14: Save Settings 12. After clicking Next, you will see the screen below. Figure 15: Final Screen If desired, you can click the Web UI button to connect to the camera using your Web Browser. Clicking the Install Utility button will install the Viewing/Recording utility described in Chapter 5. 13. Click Exit to end the Wizard. Setup is now complete.
Chapter 3 Advanced Viewing Setup 3 This Chapter provides information about the optional settings and features for viewing video via the Wireless Network Camera. This Chapter is for Administrators only. Introduction After finishing setup via the Windows-based Wizard, the Wireless Network Camera can immediately be used by all users on your LAN. Refer to Chapter 5 - Viewing & Recording for details on viewing and recording live video.
Figure 16: Video Image Screen 3. Make the required adjustments, as explained below, and save your changes. Encoding Image Type Select the desired type: • MPEG-4 gives smooth motion and high quality images, but the video image quality will deteriorate if insufficient bandwidth is available. • JPEG requires more bandwidth than MPEG-4, but if the bandwidth is insufficient, the frame rate will drop, and the image quality will remain at the same level.
Adjustment Color Select the desired option to match the current environment and lighting. Exposure If necessary, you can adjust the exposure to obtain a better image. For example, if the camera is facing a bright light, the image may be too dark. In this case, you can increase the exposure. Sharpness Select the desired option for the sharpness. You can select a Sharpness value between -3 and 3.
Controlling User Access to the Video Stream By default, all users can connect to the Wireless Network Camera and view live Video. If desired, you can limit access to scheduled times, and also restrict access to known users. To use these features 1. Connect to the Web-based interface of the Wireless Network Camera. (See Chapter 4 Web-based Management for details.) 2. On the Administration menu, select Video Access.
Making Video available from the Internet If your LAN is connected to the Internet, typically by a Broadband Gateway/Router and Broadband modem, you can make the Wireless Network Camera available via the Internet. Wireless Network Camera Setup The Wireless Network Camera configuration does NOT have be changed, unless: • You wish to change the port number from the default value (1024). • You wish to use the DDNS (Dynamic DNS) feature of the Wireless Network Camera.
Figure 19: DDNS Screen 3. Operation is then automatic: • The Wireless Network Camera will then automatically contact the DDNS server whenever it detects that the Internet IP address has changed, and inform the DDNS server of the new IP address. • Internet users can then connect to your LAN using the Domain Name allocated by the DDNS service provider. Router/Gateway Setup Your Router or Gateway must be configured to pass incoming TCP (HTTP) connections (from Viewers) to the Wireless Network Camera.
Figure 20: Connecting via the Internet The "Port" for the Port Forwarding / Virtual Server entry above is the "User-defined Port" number specified on the Video Access screen of the Wireless Network Camera. Viewing via the Internet Clients (viewers) will also need a broadband connection; dial-up connections are NOT recommended.
Figure 21: Add Camera from Internet You can then select the camera in the Cameras list on the main screen, and click View to establish a connection and view live video. See Chapter 5 - Viewing and Recording for full details on using the Windows Viewing/Recording utility. Using your Web Browser If using your Web browser, you need to know the address of the camera (either the Internet IP address or the Domain name) and the correct port number.
Motion Detection Alerts The Motion Detection feature can generate an Alert when motion is detected. The Wireless Network Camera will compare consecutive frames to detect changes caused by the movement of large objects. But the motion detector can also be triggered by: • Sudden changes in the level of available light • Movement of the camera itself. Try to avoid these situations.
3. 4. If using a schedule, click the Alert Schedule button and define the desired schedule. Set the desired options for the Delay between Alerts and the Video file to accompany the Alert. 5. To have alerts sent by E-mail: 6. • Enable the E-Mail Alerts checkbox • Enable and enter at least one (1) E-mail address • Select or enter the desired options for Attachment, From and Subject fields.. • Click the SMTP Server button, and enter details of the SMTP Server used to send the E-mail.
Chapter 4 Web-based Management 4 This Chapter provides Setup details of the Wireless Network Camera’s Webbased Interface. This Chapter is for Administrators only. Introduction The Wireless Network Camera can be configured using your Web Browser. The Wireless Network Camera must have an IP address which is compatible with your PC. The recommended method to ensure this is to use the supplied Windows-based Wizard, as described in the previous chapter.
Welcome Screen When you connect, the following screen will be displayed. Figure 23: Welcome Screen The menu options available from this screen are: • Exit - Terminate the connection to the Wireless Network Camera. • View Video - View live Video using your Web Browser. • Administration - Access the Administration menu. These options are explained in the following sections.
View Video Screen To view live video in your Browser, click the View Video link. You may see a prompt regarding an "OCX" file, like the example below. You must install this OCX file in order to view the Video. Click "Yes". Figure 24 ActiveX OCX Prompt Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered.
Administration Menu Clicking on Administration on the menu provides access to all the settings for the Wireless Network Camera. The Administration menu contains the following options: Setup • System • LAN • DDNS • Wireless Video Stream • Video Image • Video Access • Users • Alerts Administration • Admin Login • Status • Log • Firmware Upgrade These options are explained in the following sections.
System Screen After clicking Administration on the main menu, or selecting System on the Administration menu, you will see a screen like the example below. Figure 25: System Screen Data - System Screen System Settings Device Name This displays the name for the Wireless Network Camera. Description This field is used for entering a description, such as the location of the Wireless Network Camera. LED Operation Enable this if you want to use this function.
Update The Schedule determines how often the Wireless Network Camera contacts the NTP Server. Select the desired options.
LAN Screen This screen is displayed when the LAN menu option is clicked. Figure 26: LAN Screen Data - LAN Screen LAN MAC Address It displays the current MAC address. Obtain Address Automatically If selected, the Wireless Network Camera will obtain its IP address and related information from a DHCP Server. Only select this option if your LAN has a DHCP Server. Fixed IP Address If selected, you must assign the following data to the Wireless Network Camera.
DDNS Screen Many internet connections use a "Dynamic IP address", where the Internet IP address is allocated whenever the Internet connection is established. This means that other Internet users don't know the IP address, so can't establish a connection. DDNS is designed to solve this problem, as follows: • You must register for the DDNS service with a DDNS service provider. The DDNS Service provider will allocate a Domain Name to you upon request.
Password Enter the password for the DDNS account. Check WAN IP Address Set the schedule for checking if the Internet IP address has changed. If the IP address has changed, the DDNS Server will be notified. Wireless Screen This screen is displayed when the Wireless menu option is clicked. Figure 28: Wireless Screen Data - Wireless Screen Wireless Setting (Wireless Network Camera only) Mode SSID The Connection Mode determines the type of wireless communication used by the Wireless Network Camera.
Channel No. • In Infrastructure mode, this setting is ignored. The Wireless Network Camera will use the Channel set on the Access Point. • For Ad-hoc mode, select the Channel you wish to use on your Wireless Network Camera. Other Wireless stations should use the same setting. • If you experience interference (shown by lost connections and/or slow data transfers) you may need to experiment with different channels to see which one is the best.
Image Screen This screen is displayed when the Image menu option is clicked. Figure 29: Image Screen Data - Image Screen Encoding Image Type Select the desired type: • MPEG-4 gives smo oth motion and high quality images, but the video image quality will deteriorate if insufficient bandwidth is available. • JPEG requires more bandwidth than MPEG-4, but if the bandwidth is insufficient, the frame rate will drop, and the image quality will remain at the same level.
Desired Frame Rate Select the desired frame rate for the camera. Reducing this will lower the amount of bandwidth required by the camera. Power line frequency Adjustment Color Select the desired option to match the current environment and lighting. Exposure If necessary, you can adjust the exposure to obtain a better image. For example, if the camera is facing a bright light, the image may be too dark. In this case, you can increase the exposure. Sharpness Select the desired option for the sharpness.
Video Access Screen This screen is displayed when the Video Access option on the Administration menu is clicked. Figure 30: Video Access Screen Data - Video Access Screen Video Access Access to Video Stream Select the desired option: • Enable - Camera is always enabled. • Disable - Camera is disabled (no video stream), and will remain disabled until you enable it. • Enable during scheduled periods - Camera is available during the scheduled periods, and unavailable at other times.
Viewer Authentication HTTP Port Select the desired option for the Viewer Authentication. • Disable - No login required • If selected, users do not have to provide a username and password when they connect to the camera to view video. • Enable - Require login • If selected, users will be prompted for a username and password when they connect to the camera to view video. The camera administrator must use the "User Database" menu option to create the desired users.
Schedule Screen This screen is displayed when the Access Schedule button on the Video Access screen is clicked. Figure 31: Schedule Screen Data - Schedule Period List This displays all periods you have entered into the database. If you have not entered any periods, this list will be empty. Delete Period Use the Delete Period button to remove the selected item in the list. Add Period Day Choose the desired option for the period. Start Time Enter the start time using a 24 hr clock.
User Database Screen This screen is displayed when the User Database option on the Administration menu is clicked. Figure 32: User Database Screen Data - User Database Screen Existing Users User List This displays all users you have entered into the User database. If you have not entered any users, this list will be empty. Buttons Use the Edit, Delete, Delete All buttons to manage the user database. User Properties User Name • Enter the name for the user here.
Alerts Screen This screen is displayed when the Alerts option on the Administration menu is clicked. .
Data – Alerts Screen Alerts Motion Detection Alerts Alerts can be sent when motion is detected. Select the desired option: • Disable - Motion detection alerts are disabled. • Enable - Motion detection alerts are always on. • Enable during scheduled periods - Motion detection alerts are enabled during the scheduled periods, and disabled at other times. Click the "Alert Schedule" button to create a suitable schedule.
Restart Sequence If using "Sequence number" for the file suffix, you can use this setting to determine how often the sequence restarts. Select the desired option for the Restart Sequence. Click the Restart Now button if you wish to restart the Sequence Number immediately. E-Mail Alerts Enable Check the box to enable the E-Mail Alert feature. E-mails are sent when motion is detected. Note: Motion detection can be triggered by rapid changes in lighting condition, as well as by moving objects.
SMTP Server Screen This screen is displayed when the SMTP Server button on the Alerts screen is clicked. Figure 34: SMTP Screen Data - SMTP SMTP Server Address Enter the address of the SMTP (Simple Mail Transport Protocol) Server to be used to send E-Mail. Authentication Select the desired Authentication type for the SMTP Server. SMTP Login name Enter your login name for the SMTP Server. SMTP Password Enter your password for the SMTP Server. POP server name Enter the name for the POP Server.
Admin Login Screen . Figure 35: Admin Login Screen Data - Admin Login Screen Password Administrator Login Name • Enter the name for the Administrator here. Spaces, punctuation, and special characters must NOT be used in the name. • The name is case insensitive (case is ignored), so you can not have 2 names which differ only by case. Administrator Password The password for the Administrator. Verify Password Re-enter the password for the Administrator, to ensure it is correct.
Status Screen . Figure 36: Status Screen Data - Status Screen System Device Name This shows the name of the Wireless Network Camera. Description This shows the description of the Wireless Network Camera, such as location. F/W version The version of the current firmware installed. You can upgrade the Firmware by clicking the Upgrade Firmware button. You need to obtain the firmware upgrade file first. Network MAC Address The current IP address of the Wireless Network Camera.
Channel This shows the wireless channel currently used. Security The current security setting for Wireless connections. Video Video Type This displays the compression type of the video stream (e.g. MPEG-4). Resolution The image size of the video stream. Current Viewers This shows how many viewers are currently viewing the Video stream. Buttons Refresh Update the log and any other data on screen. Restart Restart (reboot) the Wireless Network Camera.
Upgrade Firmware Screen This screen is displayed when you click the Firmware Upgrade button on the Status screen. Figure 37: Firmware Upgrade Screen This screen allows you upgrade the Firmware (software) in your Wireless Network Camera. Before using this screen, your must download the upgrade file to your PC. Then follow this procedure: 1. Click the Browse button, and locate the upgrade file. 2. 3. Select this file, and click OK. The filename will then appear in the Upgrade File field.
Chapter 5 Viewing & Recording 5 This Chapter describes how to view and record the live video stream generated by the Wireless Network Camera. Overview The recommended method to view video is to use the supplied Windows Viewing/Recording utility. Installation 1. Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run Setup.exe in the root folder. You will see the Welcome screen shown below. Figure 38: Welcome Screen 2. 3.
System Tray Icon When started, the program will create an icon in the Windows system tray on the taskbar, as shown below. Figure 39: System Tray Icon This Icon has the following functions: • Animation - If a recording is in progress, this icon will be animated. Otherwise, it is stationary. • Hover - Hovering your mouse over this icon will generate a pop-up informing you of the current status. • Double-click - This will display the main screen, shown below.
Viewing Live Video You can view live video in the main screen. The built-in software can let you view up to 16 cameras on a single computer screen at one central location. The Icons allow you to control the cameras and video streams. Exit - Click this to exit the program. Shrink to task bar - Use this to minimize the program. Play - Use this to re-start viewing, after using the Stop or Pause button. Pause - Use this to temporarily stop the connection to the camera Stop.
Adding Cameras to the List To add a camera to the Channel List, click the Setup button on the main screen. You will see a screen like the example below. Figure 41: Channel List Tab Screen • Click the Add button. • The Cameras on LAN panel, on the left, displays all Wireless Network Camera found on your LAN. This list can be updated by clicking the Refresh button. • The Camera Data panel, on the right, displays the data for the selected camera.
Figure 42: Add Camera from LAN To add a camera to the Camera List on the main screen: 1. 2. 3. Select a camera in the list on the left. Check that the Camera Data shown on the right is correct. See below for details. Click the Add button. The camera will now appear in the Channel List on the TabCamCfg screen. Camera Data - LAN Camera Name This is the default name for the Wireless Network Camera, and cannot be changed. Address The current IP address of the Wireless Network Camera.
Adding Cameras on the Internet If the Wireless Network Camera you wish to add is not on your LAN, but is available via the Internet, click the Internet button. You will see a screen like the example below. Figure 43: Add Camera from Internet To add a camera to the Camera List on the main screen: 1. Enter the Camera Data on the panel on the right. See below for details. 2. 3. Click the Test button to check that a connection and login can be performed successfully. Click the Add button.
You can add the same Camera twice, once for the LAN, and again for the Internet. This will allow viewing the camera whether you are on the same LAN as the camera or in a remote location.
Recording Video You can record Video while watching, or schedule recordings to occur when you are absent. Recordings are stored in a standard Microsoft ASF file format, and can be played using Microsoft Media Player. Before doing any recording, you should review the recording settings to ensure they are suitable for your PC. Recording Preferences To set the Recording Preferences, click the Setting tab on the TabCamCfg screen. You will see a screen like the example below.
Recording Time Frame Maximum time frame for Instant This sets the maximum size of a recording which is started by clicking the Record button on the main screen. If the recording is not stopped manually, it will be terminated after the time period indicated here. Disk Allocation for Recording Total Space It displays the total space of the disk. Available Space It displays the available space of the disk. Enable Diskspace limit Enable this if you want to use this feature.
Live Recordings You can start and stop recording from the Main screen, using the controls provided. Exit - Click this to exit the program. Shrink to task bar - Use this to minimize the program. Play - Use this to re-start viewing, after using the Stop or Pause button. Pause - Use this to temporarily stop the connection to the camera Stop. This will terminate the connection to the camera, halting both the viewing and the recording (if in progress). Record.
Scheduled Recordings Recordings can be scheduled at any time, for any known Wireless Network Camera. (Of course, your PC must be ON at the scheduled time.) To use this feature, click the Scheduled Recording button under the Channel List tab. You will see a screen like the example below. Figure 45: Scheduled Recording List This screen lists all scheduled recordings. For each recording, the following data is shown: • Type - Indicates if the recording is One Time, Everyday, or on a particular day each week.
each week. The Start Day indicates when the first recording will be made. • Start Date Every Sunday, Every Monday, … - The recording is made on the specified day each week. The Start Day indicates when the schedule becomes active. Select the desired date. • For a single recording, this is the day the recording will be made. • For daily (Everyday) recordings, this is the starting date. • For weekly recordings, this determines when the schedule becomes active.
Viewing with your Web Browser The recommended method to view live video from the Wireless Network Camera is to use the Windows utility. However, you can also use your Web browser if necessary. Viewing over your LAN To establish a connection from your PC to the Wireless Network Camera: 1. 2. Start your WEB browser. In the Address box, enter "HTTP://" and the IP Address of the Wireless Network Camera, as in this example, which uses the Wireless Network Camera's default IP Address: HTTP://192.168.0.99 3.
Figure 47: View Video Screen • If using Internet Explorer on Windows, you may see a prompt regarding an "OCX" file, like the example below. You must install this OCX file in order to view the Video. Click "Yes". Figure 48 ActiveX OCX Prompt • Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered.
Viewing via the Internet If the LAN with the Wireless Network Camera is connected to the Internet, and configured correctly, you can connect to the Wireless Network Ca mera via the Internet. See Making Video available from the Internet in Chapter 3 for details of the required LAN configuration. To establish a connection from your PC to the Wireless Network Camera via the Internet: 1. 2. Obtain the Internet address and port number of the Wireless Network Camera from the Administrator.
6. Click View Video to see a screen like the example below. Figure 50: View Video Screen • If using Internet Explorer on Windows, you may see a prompt regarding an "OCX" file, like the example below. You must install this OCX file in order to view the Video. Click "Yes". Figure 51 ActiveX OCX Prompt • Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered. Note: Viewers need a broadband Internet connection to view video effectively.
Chapter 6 Troubleshooting 6 This chapter covers the most likely problems and their solutions. Overview This chapter covers some common problems that may be encountered while using the Wireless Network Camera and some possible solutions to them. If you follow the suggested steps and the Wireless Network Camera still does not function properly, contact your dealer for further advice. Problems Problem 1: I can't connect to the Wireless Network Camera with my Web Browser to configure it.
If you are just trying to view Video, the User Name/Password prompt indicates that the Administrator has restricted access to specified users. Ask the Administrator for your User Name and Password. Problem 4 I can't connect to the Wireless Network Camera using a Wireless connection. Solution 4 1) If a LAN cable is connected to the LAN port, the Wireless interface is disabled. Only one interface can be active. 2) Check that your PC and the Wireless Network Camera have compatible Wireless settings.
Appendix A Specifications A Wireless Network Camera Model Wireless Network Camera Dimensions 164 mm (L) * 88 mm (W)* 54 mm (H) 6.4 inch (L) * 3.5 inch (W) * 2.1 inch (H) Operating Temperature 0° C to 40° C Storage Temperature -10° C to 70° C Network Protocols: TCP/IP, DHCP, SMTP, NTP, HTTP Network Interface: 1 Ethernet 10/100BaseT (RJ45) LAN connection Wireless interface IEEE 802.11b/802.
Regulatory Approvals CE Approvals The Wireless Network Camera and the Ethernet Network Camera meet the guidelines of the European Union and comply with the 99/5/EEC and RTTE 99/ 5EG directives, including the following standards: • EN60950 • EN300 328-2 • EN301 489-1 • EN301 489-17 This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Copyright Notice Many software components are covered by the GNU GPL (General Public License). Some are covered by other Licenses as listed in the table below. Details of each applicable license are contained in the following section. No Warranty THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
thttpd License Copyright 1995,1998,1999,2000 by Jef Poskanzer . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
cgi-LIB Copyright Notice Author: Noel V Aguilar Version: 1.4 Filename: cgi-lib.h Program Library: CGI-LIB Feel free to use, copy, reference, or modify this program in any way. Support public domain freeware. For updates or to report bugs go to my home page http://www.geocities.com/SiliconValley/Vista/6493/ The web page for the library is: http://www.geocities.com/SiliconValley/Vista/6493/cgi-lib.
GNU General Public License GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on
directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
Lesser GNU General Public License GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".) "Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9.
and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission.
