User's Manual

ManualsBrandsARRIS Group ManualsElectronicsUniversal Digital Transport Adapter

HD -DTA100u

Quick Start Guide

Cable In

To TV

CH 3/4

Switch

HDMI

Power

or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS

Enterprises, Inc.

ARRIS reserves the right to revise this publication and to make changes in content from time to time without obligation on the

part of ARRIS to provide notication of such revision or change. ARRIS provides this publication without warranty of any kind,

implied or expressed, including, but not limited to, the implied warranties of merchantability and tness for a particular purpose.

ARRIS may make improvements or changes in the product(s) described in this publication at any time.

594797-001-a 01/14

The HD-DTA100u

will not turn on

• Make sure the POWER LED on the front of the HD-DTA100u is lit

green.

• If the HD-DTA100u is connected to a switched outlet, make sure the

switch is turned on. It is recommended to use an unswitched outlet,

if possible.

• Unplug the HD-DTA100u from the AC outlet, and then plug it back in.

• Make sure the remote control is in DTA mode, and turn the

HD-DTA100u on by pressing the DTA button.

The remote control

does not work

• Make sure the remote control is in DTA mode.

• Make sure there are no obstructions between the remote control

and the HD-DTA100u. Aim the remote control directly at the

HD-DTA100u front panel, not the TV or VCR.

• The angle between the remote control and the HD-DTA100u may be

too large. Stand in front of the HD-DTA100u and not too far to either

side.

• Press and release operation buttons one at a time, rmly and

deliberately.

• Check the batteries in the remote control. Install new batteries if

needed.

There is no video

on the TV screen

• Make sure the TV is on and set to the appropriate input source for

the HD-DTA100u.

• Make sure the HD-DTA100u is on and tuned to an authorized cable

channel.

• Make sure the cables between the HD-DTA100u and the TV are

rmly connected.

• Make sure the coaxial cable feed is rmly connected to the

HD-DTA100u and the wall jack.

There is no audio

when viewing

cable channels

• Press MUTE on the remote control to restore sound.

No closed captions

display

• Make sure closed captions are enabled on the TV. (Note: Closed

captioning may not be available for the current program.)

Troubleshooting

Check here before calling your service provider.

Summary of content (10 pages)

PAGE 1
Troubleshooting Check here before calling your service provider. The HD-DTA100u will not turn on The remote control does not work There is no video on the TV screen • Make sure the POWER LED on the front of the HD‑DTA100u is lit green. • If the HD-DTA100u is connected to a switched outlet, make sure the switch is turned on. It is recommended to use an unswitched outlet, if possible. • Unplug the HD-DTA100u from the AC outlet, and then plug it back in.
PAGE 2
Setting Up Your HD-DTA100u and RF4CE Remote Control IMPORTANT! Read the enclosed Safety Instructions before you begin. 1. Connect your cable service. Connect the coaxial cable from your wall outlet to the Cable In port on the HD-DTA100u. 2. Connect your TV. If you have a high-definition TV, use the HDMI connector. If you have a standard-definition TV, use the To TV connector. 3. Plug in the HD-DTA100u. Connect the power cord to the HD-DTA100u, then plug it into an unswitched electrical outlet. 4.
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
PAGE 4
• • • comporte deux lames, plus une tige de mise à la terre. La lame la plus large ou la tige de mise à la terre vise à assurer votre sécurité. Si la fiche fournie refuse de s’insérer dans une prise murale, faites remplacer la prise en question par un électricien compétent. Protégez le cordon d’alimentation pour éviter que l’on marche dessus ou qu’il soit écrasé, surtout à proximité de la fiche, des prises utilitaires et de l’endroit où le cordon émerge de l’appareil.
PAGE 5
During Transportation to the Subscriber Home • • Transport the cable terminal in its shipping box or an equally padded container. Do not expose the terminal to rain or moisture. During Installation • • • • • • • • Do not place the terminal in an enclosed area where the cooling vents are blocked or impede the flow of air through the ventilation openings. Install the terminal so that its position does not interfere with its proper ventilation.
PAGE 6
Caution: Changes or modifications not expressly approved by ARRIS for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 7
Radiation Exposure Statement The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.
PAGE 8
SOFTWARE LICENSE ARRIS Enterprises, Inc. (“ARRIS”) 3871 Lakefield Drive, Suwanee, GA 30024 IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE (“LICENSE”) CAREFULLY BEFORE YOU USE ANY SOFTWARE, FIRMWARE AND RELATED DOCUMENTATION (“SOFTWARE”) PROVIDED WITH ARRIS DIGITAL CABLE RECEIVER OR HOME THEATER SYSTEM (EACH SHALL BE REFERRED TO IN THIS LICENSE AS A “RECEIVER”). BY USING THE RECEIVER AND/OR USING ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF THIS LICENSE.
PAGE 9
modifying the Software to make it operate on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws.
PAGE 10
derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation. CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. Carnegie Mellon requests users of this software to return to Software Distribution Coordinator or Software.Distribution@CS.CMU.