User Manual Gigabit Ethernet Router with HPNA and 802.11n / 2108-N9 Gigabit Ethernet Router with 802.
ENGLISH Safety Information IMPORTANT SAFETY INSTRUCTIONS – POWER SUPPLY INSTALLATION. Connect the power supply cord to the power jack on the Motorola Netopia® Gateway. Plug the power supply into an appropriate electrical outlet. CAUTION: Depending on the power supply provided with the product, either the direct plug-in power supply blades, power supply cord plug or the appliance coupler serves as the mains power disconnect.
1 Checklist Check your package contents. It should contain the items shown here: ENGLISH Thank you for selecting the Motorola Netopia® 2108-D9 or -N9 Gigabit Ethernet Gateway. This guide will help you set up and configure your network. 1 Yellow RJ-45 Ethernet Cable User Manual Wall m 1 Gray RJ-45 Ethernet Cable ounti ng Kit Motorola Gateway Wallmounting Kit (2 screws + 2 anchors) Power Supply If you don’t have everything, contact your supplier immediately.
2 Connections ENGLISH 1. Select a suitable place on the network to install the Wireless Gateway. You can stand it up in its stand; lay it flat on a desktop; or mount it on a wall using the included wall mounting kit hardware (see “Wall Mounting instructions (optional)” on page 15). 2. Use standard Cat5 Ethernet cables to connect PCs to the LAN ports on the rear of the Wireless Gateway. One is supplied with your Gateway (yellow cable). 3.
• The Internet LED may initially be OFF.
ENGLISH The figure below shows how to connect a Motorola 2108-N9 HPNA-enabled Gateway to a home coaxial cable network using a Motorola HPNA Adaptor (purchased separately). Follow the same steps to connect any Ethernet device such as a hub or printer to a coaxial cable network. wall jack HPNA port Motorola 2108-N9 Gateway In-House Coax Wiring Ethernet settop box Motorola HPNA Adapter wall jack 6. Enable Wireless devices.
The Wireless Gateway's default settings are as follows. Setting Wireless Default value: unique to your Gateway This may be changed on the Wireless screen, on the Wireless Gateway's main menu. Default Broadcast SSID: Disabled Default Security: WEP128 Use the Wireless screen on the main menu to change this as required. ENGLISH SSID Wireless Gateway Ensure the Wireless Gateway and the other Wireless Stations are using the same settings.
When all of your connections are complete, the status LEDs on the front of your Motorola Neto- ENGLISH pia® Gateway will light, in accordance with the following diagram: Front View Power LAN 1~4 HPNA (2108-N9 model only) WPS Wireless WAN Internet LED Definition Power (Green, Red) 8 Off = Power Off Green = Power On Red = either power supply had become unstable or POST failed Blinking Red = Posting Blinking Green = FW upgrading
LED Definition Internet Off = No IP connection Solid Green = IP connection exists Blinking Green = IP level traffic Off = No connection Solid Green = Connection Blinking Green = traffic LAN 1~4 Off = No connection Solid Green = Connection Blinking Green = traffic HPNA (2108-N9 model only) Off = No connection Solid Green = Connection Blinking Green = traffic Wireless Off = No connection Solid Green = Connection Blinking Green = traffic WPS (Green, Yellow, Red) ENGLISH WAN Off = No action Solid Gre
3 Device Configuration ENGLISH You can access the configuration pages at any time as follows: 1. Run a Web browser, such as Firefox, Safari, or Microsoft Internet Explorer, and enter http://192.168.1.254 in the URL Address text box. Press Return. 2. When prompted, enter the Username and Password supplied by your ISP, if required. Some ISPs do not require Username and Password. Refer to your ISP. 3. Refer to the data from your ISP, and the table below, to ensure your choices are correct.
4. Check your connection. Click the HOME link at the top-left of your browser’s GUI display. View this page to verify that an internet connection has been established. If the connection is not successful, check the data you entered and the cabling connected to Gateway's Ethernet ports. ENGLISH Congratulations! Your connection is up and running and you should be able to browse the Internet by typing a URL address in your browser’s Address text box or by selecting any of your favorite bookmarks.
ENGLISH Client Configuration Your Gateway serves Dynamically-assigned IP addresses by default. Be sure to configure each computer connected to your Gateway to accept a Dynamically-assigned IP address, commonly referred to as DHCP. Microsoft Windows: Step 1. Navigate to the TCP/IP Properties Control Panel. a.
ENGLISH c. Windows Vista is set to obtain an IP address automatically by default. You may not need to configure it at all. To check, open the Networking Control Panel and select Internet Protocol Version 4 (TCP/ IPv4). Click the Properties button. The Internet Protocol Version 4 (TCP/IPv4) Properties window should appear as shown. If not, select the radio buttons shown above, and click the OK button.
Macintosh Mac OS 9 or Mac OS X: Step 1. Access the TCP/IP or Network control panel. a. Mac OS 9 follows a path like this: ENGLISH Apple Menu -> Control Panels -> TCP/IP Control Panel b. Mac OS X follows a path like this: Apple Menu -> System Preferences -> Network Step 2. Select Built-in Ethernet Step 3. Select Configure Using DHCP Step 4. Close and Save, if prompted.
Support Note the serial number (SN:) of your Gateway. It is located on the label on the bottom of the Gateway below the model number. You will need the Gateway’s serial number if you need to call for technical support. ENGLISH Answers to many frequently asked product-related questions, as well as full product documentation with advanced configuration instructions, are also available on-line at: http://broadband.motorola.com/consumers/support/default.
ENGLISH Recycling your Motorola Equipment Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local authorities for information about practices established for your region. If collection systems are not available, call Motorola Customer Service for assistance. Please visit http://www.motorola.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
The user manual of transmitter devices equipped with detachable antennas shall contain the following information in a conspicuous location: This device has been designed to operate with the antennas listed below, and having a maximum gain of [1.8] dB. Antennas not included in this list or having a gain greater than [1.8] dB are strictly prohibited for use with this device. The required antenna impedance is [50] ohms.
