Getting Started Instructions

ManualsBrandsArista ManualsComputers & Accessories802.11 a/n/ac/ax + b/g/n/ax Access Point

Table Of Contents

Headquarters

408 547-5500

www.arista.com

Arista, Mojo, the Arista logo, and the Mojo logo are trademarks or registered trademarks of Arista

Networks, Inc. and Mojo Networks, LLC. in the U.S. and other countries.

Support

408 547-5502

866 476-0000

support-wi@arista.com

Sales

408 547-5501

866 497-0000

sales@arista.com

Our social responsibility includes conducting business in a manner that minimizes our ecological impact on the

environment and reducing waste in our supply chain. To that end, the Quick Start Guide and Safety Manual are

available at www.arista.com.

Getting Started

Instructions on getting started with your new access point, including installation and initial conguration instructions

are available at -

http://www.arista.com/en/support/product-documentation

Other documents available at this location include:

• Quick Start Guide

• Compliance and Safety Guide

• Conguration Manual

You may also download current software, as well as view FAQs, Warranty Information, Knowledge Base articles,

Security Advisories, Software Licenses, and Field Notices at http://www.arista.com/en/support

Receiving and Inspecting the Equipment

Upon receiving the access point, inspect the shipping boxes and record any external damage. Retain the packing

materials if you suspect that part of the shipment is damaged; the carrier may need to inspect them.

If the boxes were not damaged in transit, unpack them carefully. Ensure that you do not discard any accessories that

may be packaged in the same box as the main unit.

Inspect the packing list and conrm that you received all listed items. Compare the packing list with your purchase order.

Obtaining Technical Assistance

Customers, partners, resellers, or distributors holding a valid Arista Service Contract can obtain technical support

through these sources:

Email: support-wi@arista.com. This is the easiest way to create a new service request.

Include a detailed description of the problem and the output of “show tech-support”.

Web: www.arista.com/en/support

A support case may be created through the support portal on our website.

PDOC-00173-01

5453 Great America Parkway

Santa Clara, CA 95054

USA

408 547-5500

www.arista.com

Summary of content (6 pages)

PAGE 1
5453 Great America Parkway Santa Clara, CA 95054 USA 408 547-5500 www.arista.com Our social responsibility includes conducting business in a manner that minimizes our ecological impact on the environment and reducing waste in our supply chain. To that end, the Quick Start Guide and Safety Manual are available at www.arista.com. Getting Started Instructions on getting started with your new access point, including installation and initial configuration instructions are available at http://www.arista.
PAGE 2
OEM-AP-C250 Getting Started Guide Package Contents The C-250 package must contain the following components. 15/16” (24mm) Mounting Bracket C-250 Ceiling Mounting the C-250 1. Affix bracket to T - Grid. 2. Rotate bracket to snap on to T- Grid. 3. Place the first mounting post on the rear-side of the device on to the lower notch of the bracket.
PAGE 3
4. Rotate the device such that the center mounting post fits in to the center notch on the bracket. 5. Ensure that all the mounting posts on the rear-side of the device are snapped in to the respective notches on the bracket. Wall Mounting the C-250 1. Drill four mounting holes in the wall. 2. Insert four anchors. 3. Affix mounting bracket on the wall 4. Attach device to the mounting Getting the C-250 Online Step 1: Power up Plug one end of an Ethernet cable into the PoE+ (802.
PAGE 4
Step 2: Connect to the network If you are using a PoE+ injector, make sure the data connection is plugged into a suitable switch port with proper network connectivity. Step 3: Check the LED status After the device is powered ON and connected to the network, a few minutes will pass until the Power/ Ethernet turns solid GREEN. This indicates that the AP is online and operational. The LEDs on the AP are: Power, 2.4 GHz, 5 GHz, Third radio, LAN1, and LAN2.
PAGE 5
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 6
Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada' s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.