ARGtek ARG-1220 WLAN Dual Band AP Router For 802.11a/b/g/n POWER KING SPACE Quick Installation Guide ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
Part I: External Installation Direction Package Content AP Router DC 12V Power Adapter Dual Band Antenna PoE DC Injector Paper QIG Manual/QIG CD 1 1 1 1 1 1 AP Router Connection Before installing the router, connect your PC to the internet through your broadband service.(If there is any problem, contact your ISP.)Then proceed through the following steps. 1. 2. 3. 4. 5. 6. Turn off your PC(s), cable/(A)DSL modem and the router. Adjust the antenna. Normally, upright is a good place to start.
The Front LED Indicator AP Router configuration The AP Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 10.10.10.254 Default IP subnet mask: 255.255.255.0 Web login User Name: admin Web login Password: admin The device has four operation modes (Gateway/Bridge/WISP/AP Client). The default IP addresses for the device are 10.10.10.
as 10.10.10.X. It will take about 55 seconds to complete the boot up sequence after power on. PoE DC Injector Configuration POE means Power over Ethernet, usually used with Wireless Device. You can use it to integrate the power and the Ethernet then connected with the RJ45 cable. ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
With POE, you can bring the power and Ethernet with long distance as far as the length of RJ45 cable. Since you used PoE DC Injector, the cable line won’t perplex you anymore. Your Access Point & Router are installed conveniently to gain more efficient bandwidth by yourself. Less space and electricity limitation, more comfortable wireless life. Part II: Internal Web Management AP Mode Setup (ADSL) 1、 Install the antenna & power adapter, and then connect the LAN cable with LAN port of this equipment.
2a. In Internet Settings / WAN /, select PPPoE (ADSL) for your WAN Connection Type and enter your User Name & Password which were presented by your ISOP company. And then press Apply 2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then press Apply ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
3. In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply 4. In Wireless Settings / Security, you may change the setting of password, and then press Apply ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
Finish setting and press Apply, the setting will be completed after rebooting around 20 seconds. Note: You have to connect ADSL cable with the WAN port of this equipment. ========================================================== ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
AP Mode Setup (IP Share) 1、 Install the antenna & power adapter, and then connect the LAN cable with LAN port of this equipment. Another side of cable line connects with RJ-45 of computer. Waiting for booting around 20 seconds. 2、 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to enter the setup frame. If you can’t enter to setup frame, you can try to set the IP address for 10.10.10.XXX and try to connect again.
2 In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then press Apply 3 In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
4. In Wireless Settings / Security, you may change the setting of password, and then press Apply ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
Finish setting and press Apply, the setting will be completed after rebooting around 20 seconds. Note: You have to connect cable line with the LAN port of this equipment. ========================================================== ARGtek Communication Inc. E‐Mail: sales@argtek.com www.argtek.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
