INSTALLATION MANUAL AV1455DN-S AV2455DN-S AV2456DN-S AV3455DN-S AV3456DN-S AV5455DN-S
Arecont Vision MicroDome™ Installation Manual MicroDome™ Surface Mount Installation Contents Package Contents....................................................................................................................................................... 3 Warranty Information ................................................................................................................................................ 3 Installation Overview .........................................................
Arecont Vision MicroDome™ Installation Manual Package Contents Item MegaPixel Camera Mounting Kit Arecont Vision CD Description MicroDome™ Ceiling template 6x Mounting Screws (#6x1” for wood or sheet metal) 6x Mounting Anchors 3/8” NPT Male to 1/2” NPT Female Adapter Network Patch Cable 3x Security Torx Dome Cover Fasteners Manual, Warranty, Installation Software Warranty Information 3 Year Limited Warranty ARECONT VISION warrants to Purchaser (and only Purchaser) (the “Limited Warranty”), that: (a) eac
Arecont Vision MicroDome™ Installation Manual Installation Overview Ceiling Gasket NPT Port Camera (Housing Mounting Screws Captive Fasteners (Hand Tighten Only) Page | 4 support@arecontvision.
Arecont Vision MicroDome™ Installation Manual Installation Tech Tip 1. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. 2. Operating Temperature -40°C (-40°F) to +50°C (122°F) 3. Always use hardware e.g. screws, anchors, bolts, locking nuts etc.
Arecont Vision MicroDome™ Installation Manual Focusing the Camera Tech Tip Tech Tip Page | 6 1. Open a live view of the camera from your web browser or the AV Software provided (AV100 or AV200). 2. Loosen the lens lock screw using a phillips head screwdriver (if necessary). Only do so if lens seems very tight when turning. Lock screw should be tightened enough to provide some friction against the lens to avoid focusing problems. 3.
Arecont Vision MicroDome™ Installation Manual Changing the Lens 1. Remove the Dome Cover by loosening the captive fasteners. 2. Loosen the lens lock screw using a phillips head screwdriver (if necessary). Only do so if lens seems very tight when turning. 3. Manually unscrew the lens, this may take several seconds. 4. Replace lens. 5. Retighten the lock screw if necessary. 6. Reinstall Dome Cover per instructions outlined above.
Arecont Vision MicroDome™ Installation Manual Digital Input and Output Use 4 position connector inside camera housing to interface with Digital I/O. DIGITAL I/O BLACK IN WHITE IN + YELLOW OUT ORANGE OUT + Electrical Characteristics Input Voltage (V) (Measured between + and – terminals) Output Current (mA) (Measured between + and – terminals) Applied Voltage Range : 0-80V MIN MAX ON 2.9 6.3 OFF 0 1.3 ON - 50 OFF - 0.
Arecont Vision MicroDome™ Installation Manual LED Indicators LED Yellow Status Flashing Green Solid None Flashing Solid None Page | 9 support@arecontvision.com Description Link has been established. Normal Operation. No connection. Camera has been accessed. Normal operation. N/A No Connection.
Arecont Vision MicroDome™ Installation Manual Support 1. Arecont Vision FAQ Page Located at ArecontVision.com 2. Check the following before you call: Restore camera to factory default with AV100, AV200 or the camera webpage. Upgrade to the latest firmware by visiting ArecontVision.com. Isolate the camera on a dedicated network and test with AV100 or AV200. Swap the “troubled” camera with a known good camera to see if the problem follows the camera or stays at the location. 3.
Arecont Vision MicroDome™ Installation Manual Installation Best Practice Begin Installation Adding Teflon thread sealing tape to all male threads Wind Vinyl electrical tape on all cables connections Connect ¾” NPT conduit pipe to junction box adapter No Does conduit pipe go through the wall? Yes Make sure position of conduit hole is at the lower side forming a “drip loop” below the camera using ¾” galvanized or flex conduit and appropriate fittings Tighten all camera screws and ¾” NPT plugs Caulk
Arecont Vision MicroDome™ Installation Manual Camera Discovery, Setup, and Configuration For camera discovery and setup please use Arecont Vision software AV200 which you can find on the CD included with your camera or at: http://www.arecontvision.com/softwares.php The user manual for the AV200 software is included on the CD and is also located on our website. To configure the camera use either the AV200 software or the web interface utility.
Arecont Vision MicroDome™ Installation Manual Wall Mount Accessory (MCD-WMT) Gasket Alignment features must be aligned for proper installation. Installation Notes: 1. 4x mounting screws are #10x1” wood or sheet metal screws (4x mount anchors also included). 2. Always ensure gaskets are properly seated. 3. Use Teflon tape on threaded interfaces. 4. 3/8” male to 1/2” female NPT adapter included. 5. Mount holes from camera housing to flange are not symmetrical.
Arecont Vision MicroDome™ Installation Manual Pendant Mount Accessory (MCD-CMT) Installation Notes: 1. 3x mounting screws are #10x1” wood or sheet metal screws (3x mount anchors also included). 2. Always ensure gaskets are properly seated. 3. Use Teflon tape on threaded interfaces. 4. 3/8” male to 1/2” female NPT adapter included. 5. Mount holes from camera housing to flange are not symmetrical. Alignment features indicated must be properly lined up for mount hole alignment.
Arecont Vision MicroDome™ Installation Manual Mount Template: MicroDome Camera Page | 15 support@arecontvision.
Arecont Vision MicroDome™ Installation Manual Mount Template: MicroDome Wall Mount Page | 16 support@arecontvision.
Arecont Vision MicroDome™ Installation Manual Mount Template: MicroDome Pendant Mount Page | 17 support@arecontvision.
Arecont Vision MicroDome™ Installation Manual Contact Arecont Vision Technical Support one of three ways: Online Portal : Support.ArecontVision.com Phone : 1.818.937.0700 (option #1) Email : support@arecontvision.com Page | 18 support@arecontvision.