INST TALL LATIO ON MA ANUAL L AV1455DN-F AV2455DN-F AV2456DN-F AV3455DN-F AV3456DN-F AV5455DN-F
Arecont Vision MicroDome™ Installation Manual MicroDome™ Recess Mount Installation Contents Package Contents ....................................................................................................................................................... 3 Warranty Information ................................................................................................................................................ 3 Installation Overview .........................................................
Arecont Vision MicroDome™ Installation Manual Package Contents Item MegaPixel Camera Mounting Kit I/O Plug Arecont Vision CD Description MicroDome™ Ceiling template Hex key, 0.
Arecont Vision MicroDome™ Installation Manual Installation Overview 3.25” Diameter Hole Ceiling Retention Arms Camera Housing Captive Fastener Page | 4 support@arecontvision.
Arecont Vision MicroDome™ Installation Manual Installation 1. Cut a hole in the ceiling using the template provided on page 12 (3.25 inches in diameter) to fit the camera housing. 2. Pull the network cable through the ceiling and plug it into the network connector on the camera housing (Note: this can be done at a later time if there is access to the network connector on the camera housing after installation into the ceiling). 3.
Arecont Vision MicroDome™ Installation Manual Focusing the Camera Tech Tip Tech Tip 1. Open a live view of the camera from your web browser or the AV Software provided (AV100 or AV200). 2. Loosen the lens lock screw using a phillips head screwdriver (if necessary). Only do so if lens seems very tight when turning. Lock screw should be tightened enough to provide some friction against the lens to avoid focusing problems. 3. Manually rotate the lens to adjust the focus until the desired image is obtained.
Arecont Vision MicroDome™ Installation Manual Changing the Lens 1. Remove the Dome Cover by loosening the captive fastener. 2. Loosen the lens lock screw using a phillips head screwdriver (if necessary). Only do so if lens seems very tight when turning. 3. Manually unscrew the lens, this may take several seconds. 4. Replace lens. 5. Retighten the lock screw if necessary. 6. Reinstall Dome Cover per instructions outlined above.
Arecontt Vision MicroDome™ ™ Installation Manual Remo oving the e Bubble e For best im mage quality in an indoor environmentt the bubble ccan be easily removed. 1. Press down on n the 2 lockingg tabs. 2. Rotate bubble counterclockkwise until it becomes freee. Page | 8 supportt@arecontviision.
Arecont Vision MicroDome™ Installation Manual Digital Input and Output Use 4 position connector provided in box to interface with Digital I/O on camera housing. Output Electrical Characteristics Input Voltage (V) (Measured between + and – terminals) Output Current (mA) (Measured between + and – terminals) Applied Voltage Range : 0‐80V Input MIN MAX ON 2.9 6.3 OFF 0 1.3 ON ‐ 50 OFF ‐ 0.
Arecont Vision MicroDome™ Installation Manual LED Indicators LED Yellow Status Flashing Green Solid None Flashing Solid None Page | 10 support@arecontvision.com Description Link has been established. Normal Operation. No connection. Camera has been accessed. Normal operation. N/A No Connection.
Arecont Vision MicroDome™ Installation Manual Support 1. Arecont Vision FAQ Page Located at ArecontVision.com 2. Check the following before you call: Restore camera to factory default with AV100, AV200 or the camera webpage. Upgrade to the latest firmware by visiting ArecontVision.com. Isolate the camera on a dedicated network and test with AV100 or AV200. Swap the “troubled” camera with a known good camera to see if the problem follows the camera or stays at the location. 3.
Arecontt Vision MicroDome™ ™ Installation Manual Moun nting Tem mplate For F best ressults use 33.25” hole saw Page | 12 suppo ort@arecontv vision.
Arecont Vision MicroDome™ Installation Manual Camera Discovery, Setup, and Configuration For camera discovery and setup please use Arecont Vision software AV200 which you can find on the CD included with your camera or at: http://www.arecontvision.com/softwares.php The user manual for the AV200 software is included on the CD and is also located on our website. To configure the camera use either the AV200 software or the web interface utility.