User's Manual

A) iReminder Unit x 1 B) Key Chain Hock x 1
C) Battery(CR 2032) x 1 D) User Manual x 1
If any components are missing from the package, please return the
product to your dealer immediately.
Product Description
3
Key Chain Hock
Battery Cover
Power Switch
LED
Multiple iReminder SB20 User Manual
An electronic leash that will sound an alarm when your iPhone leaves
your vicinity. You can also use your iPhone to find the lost iReminder
thanks to the duplex communication protocol. A handy app called
HiProx Multi, will show on Google Map the last time the iReminder and
phone were connected. As a remote shutter release for self-portraits or
to prevent blur by shaking camera. The app can control the alarm
threshold distance, set the iReminder to start beeping when a call is
incoming, and switch the proximity alarm on/off. HiProx Multi for use
with multiple iReminder units and includes all of the mentioned
features. Simple to use interface allows you to re-name each tag
attached to your valuables, such as Keys, Wallet, etc. A brilliant little
device that could save you a lot of trouble.
1 Introduction
Quick Setup Guide
Step 1 - Download App ”HiProx Multi”
Download ”HiProx Multi” on App Store for free.
(Please search for HiProx Multi on App store, or search for BLE and
find the HiProx Multi application)
Step 2 - Enable Bluetooth on your iPhone/iPad
Go to Setting General Enable Bluetooth
Step 3 - Place battery into iReminder Units
a. Open the battery cover by placing your thumb on the cover
(as shown) and pulling it backwards until it clicks open; then lift
off the cover.(Figure 1)
b. Insert the battery into the battery compartment with the the ”+”
sign on the battery facing up. Then replace the battery cover
by sliding it up into compartment opening.(Figure 2)
Specification
Product description
2
4
1 Introduction
5
Quick setup guide
Front
Back
Step 4 - Turn on the iReminder Units
Once turn on the iRminder units, and it will enter automatically to
pairing mode. Green LED will blink per second to indicate device is
ready to pair.
Page 1
Package components
3
Communication Standard Bluetooth® 4.0 Low Energy Wireless Technology
Compatibility
iPhone 4S/5, iPad 4, New iPad, iPad Mini with iOS 6 or later
Search Range
164ft/50m(*Distance will vary depending on terrain and other factors.)
Alert Range 6~50ft/2~15m adjustable (Near: 16±10ft/5±3m, Far: 32±16ft/10±5m)
Battery Type CR2032x1
Battery Life 6~12 months
Dimension/Weight 61.5x36x11.6mm (2.42x1.42x0.46inch) / 9.5g
Working Temperature
Temperature: 5℃~40℃, humidity : 20%~80%
Power Off
Power On
Step 5 - Run ”HiProx Multi” application
a. Open ”HiProx Multi” and tap the button in the upper right
corner to discover all available devices.(Figure 3)
b. ”HiProx Multi” will pop up Bluetooth Pairing Request.(Figure 4)
c. Select ”Pair” from ”Bluetooth Paring Request” for each device. The
Green LED light will blink once every 5 seconds in the connecting
mode.
Step 6 - Test the iReminder system
a. From MainView available devices table, you can tap desired item to
select that device. Once device has been selected, button will
appear in that row.(Figure 5)
b. Press button, the iReminder unit will beep to do FindMe function.
c. Press ”FindMe” button on the iReminder unit , and your BLE device
will beep.
d. Press and release ”Find Me” button to stop the FindMe function.
e. To set different alarm sounds for each tag, press 'Alarm Button'
(Figure 6)and go to Alarm Sound Selection View to choose your alert
tone for that tag.
f. Set alarm ”threshold level” depends on the alarm distance you like.
Step: Range Alarm Threshold Move the threshold bar
depends on the distance alarm you need.(Figure 6)
g. Test your setup by placing the iPhone in a stationary location. Then
take the Reminder and walk away from the iPhone - when you reach
6-50 feet from the iPhone, the Reminder will begin to beep. If you
move back into the range, the alarm will cease. (Figure 8)
Figure 1
Figure 2
Device FindMe
Button
6-50 Feet
a. To locate the missing item, tap green button from available
device st. The missing device will continue beep for 5 seconds
from each request. Re-tap green button again to continue
searching function.
b. Press and Release Device 'FindMe' button (hardware button under
the LED) will gernerate ”FindMe Request” from that Device. Your
iOS device (iPhone / iPad...) will issue Alert sound continuesly.
Press and Release Device FindMe button to stop this request.
c. Tap green button from iOS Device will Mute 'FindMe Request
Alert Sound.
d. Holding the device button for over 3 seconds will force the device
to enter SLEEP mode and generate a linkLossAlert to the iOS
device; to wake up and re-connect to the iOS device, ress and
release device button.
FindMe Function
6
Figure 8
1. Enter Help menu
2. Find new device
3. Find my tag
4. Setting button
5. Signal indicator
6. Remove tag button
7. Beep sound setting for tag
8. Change device name
9. Battery status
10. On/Off call alert function
11. On/Off link loss function
12. On/Off range alarm function
13. Set alarm range
14. Alarm sound setting
15. On/Off Map location function
16. Enter Map view menu
17. Enter Camera function
18. Enter airplane mode setting
Figure 3 Figure 4
Figure 6
Figure 5
Figure 7
2
18
1
Signal Indication
3 4
5
8 97
14
10
11
12
13
15
16
17
6
Beep Sound High Alert: 95±3db, Mid Alert: 90±3db (at 10cm/3.9inch)